Abstract:The original Johnson-Cook model's poor prediction of W90 alloy stress at high strain rate and high and low temperatures restricts research and utilization of this alloy. This study used a Split Hopkinson Pressure Bar (SHPB) device to conduct dynamic compression tests on W90 alloy over a temperature range of [-90°C,700°C] and analyze its mechanical behavior. We examined the material's different plastic phase characteristics at high and low temperatures and conducted microstructure research on impact test specimens. Then, we analyzed the stress-strain data from SHPB experiments and quasi-static compression tests on the classical Johnson-Cook model. The original Johnson-Cook model was calibrated using the stress-strain data from SHPB and quasi-static compression tests, and the modified Johnson-Cook model was established and verified. The results show that: low temperature significantly strengthens the material's stress, while increasing temperature thermal softening reduces stress; increasing strain rate increases the strain generated by the workpiece, causing faster strain hardening and thermal softening effects, resulting in higher and more stable stress; low temperature makes thicker grain boundaries, increasing plastic stress, and increasing strain rate also increases plastic stress, as well as making the material's grain boundaries thicker. The increase of strain rate makes the grain more dense, which will also show up in the increase of stress on the macroscopic level; the modified Johnson-Cook model in this paper has high agreement with experimental data, with a mean value of MAPE of only 1.85 %,which is 90.20 % lower than the traditional model, and the average value of the RMSE is 85.56 % lower than the traditional model. The modified model significantly outperforms the traditional model in predicting stress and better describes stress changes in W90 at different temperatures.

Plastic Flow Modeling of Ti-5Al-2Sn-2Zr-4Mo-4Cr Alloy at Elevated Temperatures and High Strain Rates

Dynamic Mechanical Behavior and Modified Johnson-Cook Model of Ti60 Alloy under High-temperature and High-strain-rate Conditions

The Constitutive Responses of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy at High Strain Rates and Elevated Temperatures

Thermomechanical Response of Commercially Pure Titanium under Large Plastic Deformation at High Strain Rates

Deformation Behavior and Constitutive Model for Isothermal Compression of TC4 Alloy

Predicting The Tensile Behavior Of Ti-6.6al-3.3mo-1.8zr-0.29si Alloy Via The Temperature-Dependent Crystal Plasticity Method

Stress-Strain Curves and Modified Material Constitutive Model for Ti-6Al-4V over the Wide Ranges of Strain Rate and Temperature

Plastic Deformation Behavior and Constitutive Modeling of Cu-50Ta Alloy During Hot Compression

The Role of Material Model in the Finite Element Simulation of High-Speed Machining of Ti6Al4V

Dynamic Strain-Rate Effect On Uniaxial Tension Deformation Of Ti5al2.5sn Alpha-Titanium Alloy At Various Temperatures

Temperature-Dependent Tension Plastic Deformation and Fracture Behavior of Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy at High Strain Rates

Dynamic Mechanical Properties and Modified Material Constitutive Model for Hot Forged Ti2AlNb over Wide Ranges of Temperature and Strain Rate

Thermo⁻Mechanical Behavior and Constitutive Modeling of In Situ TiB2/7050 Al Metal Matrix Composites Over Wide Temperature and Strain Rate Ranges

Analysis of the High Temperature Plastic Deformation Characteristics of 18CrNi4A Steel and Establishment of a Modified Johnson–Cook Constitutive Model

Hot deformation behavior and microstructure evolution of TC11 dual-phase titanium alloy

Flow Behavior and Constitutive Equation of Ti-6.5Al-2Sn-4Zr-4Mo-1W-0.2Si Titanium Alloy

Strain Rate Sensitivity of Tensile Properties in Ti-6.6Al-3.3Mo-1.8Zr-0.29Si Alloy: Experiments and Constitutive Modeling

Phenomenological Constitutive Model and Physical Constitutive Model of Hot Deformed Dual-Phase Ti-5Al-4Sn-2Zr-5Mo Alloy

Mechanical properties and JC constitutive modification of tungsten alloys under high strain rates and high/low temperatures

Comparative Study on Several Constitutive Models of GCr15 Steel at High Strain Rates

Research on Johnson–Cook Constitutive Model of γ-TiAl Alloy with Improved Parameters