Abstract:Longitudinal-torsional ultrasonic vibration-assisted milling is a machining method that can effectively improve the quality of the machined surface. When this method is used for the end milling of TC18 titanium alloy, however, the law of influence on the machined surface and subsurface remains unclear. In this study, we examined the effects of the ultrasonic amplitude, feed rate, and cutting speed on the machined surface morphology, roughness, surface residual stress, and subsurface microstructure in the longitudinal-torsional ultrasonic vibration-assisted end-milling process. According to the results, longitudinal-torsional ultrasonic vibration-assisted end milling can help form more obvious surface microtextures with a more distinct surface texture regularity at large amplitude, small feed rate, and high cutting speed. Compared with conventional milling, longitudinal-torsional ultrasonic vibration-assisted milling generates a larger roughness and surface residual stress and a deeper plastic deformation layer of the subsurface in the case of an obvious highly perturbed layer. In addition, the surface residual stress becomes greater and the plastic deformation layer gets deeper at a larger amplitude. When the amplitude was 5 μm, the surface residual stress was − 450.625 MPa and the depth of the deformation layer was 5.4 μm. The stress and depth increased by 21.55 % and 134.78 %, respectively, compared with those of conventional milling. The increase in the feed rate enhanced the roughness, decreased the surface residual stress, and did not significantly alter the depth of the plastic deformation layer. When the feed rate was 0.01 mm/z, the roughness was 0.383 μm and the surface residual stress was − 479.1 MPa. The feed rate and roughness increased by 42.63 % and 20.62 %, respectively, compared with those of conventional milling. With the increase in the cutting speed, the roughness increased, and the surface residual stress and the depth of the plastic deformation layer decreased. When the cutting speed was 15 m/min, the roughness was 0.31 μm, the surface residual stress value was − 454.7 MPa, and the depth of the plastic deformation layer was 5.7 μm. These three parameters increased by 17.8 %, 18.79 %, and 92.5 %, respectively, compared with those of conventional milling. This research has certain application prospect in surface machining of titanium alloy and quality control of machined surface.

Research on Machining Quality Control in Micro Milling of Low-Rigidity Characteristics

Milling Error Prediction of Thin-Walled Parts During High-Speed Machining

A Processing Technical Analysis for the Characteristics of Forces and Surface Roughness in Micro-Scale Milling

Deformation Control in Mesoscale Micro-Milling of Curved Thin-Walled Structures

Experimental Investigation on Machinability of Aluminum Alloy during Dry Micro Cutting Process Using Helical Micro End Mills with Micro Textures

Investigation on the Tool Wear Suppression Mechanism in Non-Resonant Vibration-Assisted Micro Milling

Optimization of the process parameters for micro-milling thin-walled micro-parts using advanced algorithms

Finite element simulation and experimental investigation on cutting mechanism in vibration-assisted micro-milling

Experimental study of a new micromilling process for vortex curved thin walls

Analysis and optimization of microchannel array precision grinding processes with micro-structured micro-grinding tool

Surface and subsurface analysis of TC18 titanium alloy subject to longitudinal-torsional ultrasonic vibration-assisted end milling

An improved time-varying stability analysis of micro milling considering tool wear

An Investigation into the Effect of Electro-Contact Heating in the Machining of Low-Rigidity Thin-Walled Micro-Machine Parts

Machining dynamics and chatters in micro-milling: A critical review on the state-of-the-art and future perspectives

Investigation on dynamic tool deflection and runout-dependent analysis of the micro-milling process

Determination of the Minimum Chip Thickness and the Effect of the Plowing Depth on the Residual Stress Field in Micro-Cutting of 18 Ni Maraging Steel

Experimental investigation and optimisation of the micro milling process of hardened hot-work tool steel

Mechanism of dual-direction vibration-assisted (DVA) micro-milling in surface formation considering the tool life-lengthening effect on the Ti6Al4V: design and experiment

Precision micro-milling process: state of the art

Investigation on Cutting Forces and Surface Finish in Mechanical Micro Milling of Zr-Based Bulk Metallic Glass

Evaluation of milling performance of 50-μm D-shaped carbide tool, polycrystalline diamond-coated carbide tool, and polycrystalline diamond tool