Abstract:Highly-conductive nanostructures may be dispersed into phase change materials (PCM) to improve their effective thermal conductivity, thus leading to colloidal systems that are referred to as nanostructure-enhanced PCM (NePCM). Results of a theoretical and experimental investigation on freezing of NePCM in comparison to the base PCM are presented. A one-dimensional Stefan model was developed to study the unidirectional freezing of NePCM in a finite slab. Only the thermal energy equation was considered and the presence of static dispersed nanoparticles was modeled using effective media relations. A combination of analytical and integral methods was used to solve this moving boundary problem. The elapsed time to form a given thickness of frozen layer was therefore predicted numerically. A cooled-from-bottom unidirectional freezing experimental setup was designed, constructed, and tested. Thermocouple readings were recorded at several equally spaced locations along the freezing direction in order to monitor the progress of the freezing front. As an example, cyclohexane (C6H12) and copper oxide (CuO) nanoparticles were chosen to prepare the NePCM samples. The effective thermophysical and transport properties of these samples for various particle loadings (0.5/3.8, 1/7.5, and 2/14.7 vol. %/wt. %) were determined using the mixture and Maxwell models. Due to utilization of the Maxwell model for thermal conductivity of both phases, the numerical predictions showed that the freezing time is shortened linearly with increasing particle loading, whereas nonmonotonic expediting was observed experimentally. The maximum expediting was found to be nearly 8.23% for the 0.5 vol. % sample. In the absence of a nanoparticle transport model, the mismatch of the cold plate boundary conditions, lack of accurate thermophysical properties, especially in the solid phase of NePCM samples and precipitation issues with 2 vol. % samples were addressed by improving the experimental setup. Through adopting a copper cold plate, utilizing measured thermal conductivity data for both phases and using 1, 2, and 4 wt. % samples, good agreement between the experimental and numerical results were realized. Specifically, adoption of measured thermal conductivity values for the solid phase in the Stefan model that were originally underestimated proved to be a major cause of harmony between the experiments and predictions. [DOI: 10.1115/1.4006305]

Phase change materials (PCM) based cold source for selective freezing 3D printing of porous materials

A Theoretical and Experimental Investigation of Unidirectional Freezing of Nanoparticle-Enhanced Phase Change Materials

A New Model of Phase Change Process for Thermal Energy Storage

Ternary composite phase change materials (PCMs) towards low phase separation and supercooling: eutectic behaviors and application

3D Printable, Form stable, Flexible Phase-Change-based Electronic Packaging Materials for Thermal Management

The efficient and developing phase transition freezing materials generated from amino acids

Simulation research on PCM freezing process to recover and store the cold energy of cryogenic gas

Rationally Tunable Phase Change Material Thermal Properties Enabled by Three-Dimensionally Printed Structural Materials and Carbon-Based Functional Additives

Water - graphene nanoplatelets based thermal energy storage material with nucleating and thickening agents: An investigation on thermal behavior during phase change

Investigation on Ternary Salt-Water Solutions As Phase Change Materials for Cold Storage

Formulation and Characterisation of Ternary Salt Based Solutions As Phase Change Materials for Cold Chain Applications

Printing Composites with Salt Hydrate Phase Change Materials for Thermal Energy Storage

Thermal Performance of a 3D Printed Lattice-Structure Heat Sink Packaging Phase Change Material

Preparation and Performance of Modified Calcium Chloride Hexahydrate Composite Phase Change Material for Air-Conditioning Cold Storage

Modified Supporting Materials to Fabricate Form Stable Phase Change Material with High Thermal Energy Storage

Preparation and the Cold Storage Performance of Water/PVA Sponge PCMs for Aerospace Applications

Preparation and performance of modified expanded graphite/eutectic salt composite phase change cold storage material

Polymer Encapsulation Strategy toward 3D Printable, Sustainable, and Reliable Form-Stable Phase Change Materials for Advanced Thermal Energy Storage

Preparation and characterization of an aluminum ammonium sulfate dodecahydrate-based composite phase change material with low supercooling and high thermal conductivity

Enhanced Mechanical and Thermal Properties of Expanded Graphite/ice Phase Change Materials Through In-Situ Polymerization of Sodium Polyacrylate in Cold Chain Logistics

Microfluidic Fabrication of Compound Microfibers Encapsulating Nano-Enhanced Phase Change Material (PCM) for Thermal Regulation