Inactivation of Peroxidase as a Function of Corn Processing
G. Inglett,R. A. A. Rson
Abstract:Vol. 46 \1casurelllcnt of pcro\.idasc activity is used a~ a me (hod by which to quantitate enzyme destruction In proces-;ed ·orn. Dry-null process1l1g u:ually results in a small amount of en/yme destructIOn. Peroxidase activities In the dry-nulled fractions vary, brgdy because of the anatomical origin of the fraction. The !!erm fraction i~much more active than the fractions derived from endosperm or pericarp. RolIand extrusion-cooking of grits often result In total inactivation of peroxidase activity. The degree of Inactivation depends upon the amount of heat and mOisture used in the process.•md it can be correlated with either water-absorption properties of the produd or consistency of a mixture of the product with water. Peroxidase activity has been used in food quality control as a biochemical index of whether heating or blanching procedures are adequate (1,2,3). Similar studies have been made on sweet-corn peroxidase (4,5,6). The stability of peroxidase to heat is greater than that of most other enzymes, and peroxidase is also easy to assay. For these reasons it serves as an acceptable measure of inactivation for a broad range of enzymes. In our study it was nl:cessary to know if peroxidase inactivation could be measured in corn processed with semidry heat encountered in dry-milling and in roll-cooking and extrusion~ooking. Special JUention was given to rolland extrusion-cooked corn products specified as acceptable for use in "Blended Food Product, F-or)l1ula No.2:' commonly called CSM (7). CSM is a food supplcment for preschool children, consisting of a formulation of heal-processed corn meal, soybean meal, nonfat dry milk, vitamins, and minerals. Over 500 million lb. of this food product has been shippcd to developing countries as of May I<)68. The variable conditions undcr wh ich CSM may be stored during and after shipment creates thc spccial requirement for enzyme inactivation. Long periods of high humidity and heat could be disastrous in cereal products with large amounts of enzyme activity. It is not known if peroxidase, per se, is partly responsible for the development of off-flavors during food storage, but J numbcr of investigators have correlated the production of viny or strawlike flavors to pcroxidase activity (J ,2,8,9). Probably other enzymes are primarily responsible for loss of quality in foods inadequately processed, including corn products. Often lipid-active enzymcs are implicated as the cause of off-flavors in cereals: among them are lipoxygcnase (Iipoxidase) in corn (10) and lipase in oat flakes (I I). MATERIALS AND METHODS Corn Varieties U.S. Grade o. I dent corn of a nonspf'cific variety was obtained from a I0C31 grJin elevator in the fall of 1966 (presumably till' I(')()5 ,.:rop). Ipresented in part at the 53rd Annual teetlOl;. Washington. D.C .. April 1!:.l68. ContributIOn from the Northern Regional Research Lahoratory. Peoria. IllinOiS 61604. ThiS IS a laboratory of the ~orthern UtilizatIOn Research and Development DiVision. Agricultural R~search Service. l:.S. Department of Agriculture. Reference to commercial products IS for Identification only and does not imply endorsement by the U.S. Department of Agriculture. C;,\RD FR. !:\GLI·TT ~ :\NDLRSO . BC~H X800 hybrid dent ..:orn (1966 crop) was a gift from Bear HybnJ CUrJl Co., Inc. Tile hybrid was crib-dried and was not subjected to higll telllperatl1re~ befure processing. A IlIgh-lysinc variety (\965 CrDp) was provided by Purdue Uniwrsity. Another hIgh-lysine variety (1967 crop) camc from D. E. Alexander. Unlvcrslty of illinOIS. Sample Preparation Dry-milled fractions were prepared from about :2 kg. corn 1/1 the followlllg manner: Tile corn was first tempered by adding wa ter to yield 2\?( mOist lire allJ blending for 3 hr. In the second temper. water was added to raise the moistur' to 24~ and blended in for 15 min. The tempered corn was then ground In ~l Mikro-Pulverizer operating at 1,200 r.p.m. and fittcd with a two-byer hardware doth screen. 1/2 in. by 1/2 in .. with the openings of the top screen placed at a 45':angle to those on the bottom. This appeared to give results comparable to those obtained by Wichser (12) with an Enroletcr for degermination in establishing a satisfactory experime ntal mill flow for dry-milling corn. Thc' corn from the Mikro-Pulverizer was dried for 20 min. at ~Q0C. to proper moisture for mIlling. about 16e;t. Subsequent milling of this material was done with an Allis-Chalmers mill according to sligh tly modified Wichser flow. The particle sizes of the screened fractions 'were: degerminator fines. -50 mesh: grits, +24 mesh: meals, -24 +50 mesh: and tlour. 50 mesh (U.S. Standard Sieve Series). For yellow dent corn. rolland extrusion-cooking studies were carried out with commercial grits (Illinois Cereal Mills. Paris, III.) containing 14% moisture. 8.17L protein, 0.37% ash, and 0.5% fat. Screen analysis was: 1% +14 mesh, 87CX +20 mesh, and 1~ 30 mesh (U .S. Standard Sieve Series). . For high-lysine corn, roll-cooking studies were carried out with a blend of corn flour and high-fat meal dry-milled from high-lysine corn grown 'in 1967 by the University of Illinois. Analyses of the blend were as follows: 12.7% moisture, 7.2?( protein. 0.5 I% ash, 2.1 o/c crude oil, 0.40% crude fiber. A measure of the degree of cooking was determined by a ring consistency test (13) and by a wa ter-absorption test (14) as modified for processed corn by Anderson et al. (15). Whenever the amount of sample was limited, the consistency was measured with :l Bostwick Consistometer (16) instead of by the ring consistency test. Peroxidase Assav A modification of the me thad of Vetter et aJ. (17) was used to assay peroxidase activity. Essen tially. I-g. samples were soaked in 2 m/. citrate-phosphate buffer for 2 hL to soften the material, and then they were thoroughly macerated with mortar, pestle. and sand, with a minimum of buffer used for the initial grinding. Because some of the corn fractions were extremely tough, reproducible results were ensured by grinding the sample completely into a paste. After the grinding, a total volume of 3