Abstract:Nowadays, lithium-ion batteries have been considered to be the superior commercial batteries in the market, thanks to their high energy density (until ca. 250 Wh/kg at cell level) and low fabrication cost (actually < 0.3 Euro/Wh at cell level). However, due to the recent global push for electrification, there is a constant need to further improve battery performance while minimalizing the cost. Besides the development of new battery materials, engineering the electrodes could be a valid solution to meet such demand. By increasing the electrode thickness to 200 μm, the active material loading in the electrode is expected to increase to over 30 wt%, hence enhancing the energy density and limiting the cost at the cell level. Nevertheless, thick electrodes fabricated by conventional coating methods suffer severely from weak mechanical strength and delamination as well as long and highly-tortuous Li-ion diffusion path, sluggish electrochemical kinetics, and poor charge/discharge rate performance. Recently, great attention has gone to 3D printing (additive manufacturing) with the promise to overcome these limitations, thanks to the porous structures of the 3D- printed electrodes. In this work, we present 450 μm thick lithium iron phosphate (LFP) electrodes produced by 3D micro-extrusion with a superior LFP loading of ca. 30 mg/cm 2 and a high areal capacity of ca. 4.2 mAh/cm 2 . Two commercial polymeric binders were employed, including carboxymethyl cellulose (CMC) and poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS). It is concluded that both CMC and PEDOT:PSS are essential to obtain well-printed 3D electrodes. While CMC contributes significantly to the mechanical strength of the 3D-printed LFP electrodes, it is of great importance to add PEDOT:PSS to avoid intra-fiber cracks. Furthermore, the electrodes containing both binders have shown significantly improved specific capacity at different C-rates compared to those formulated from either CMC or PEDOT:PSS. Further analyses give insights into charge transfer resistance, tortuosity and electrical conductivity of the investigated electrodes. Additionally, we highlight the difference in the battery performance of 3D-printed electrodes and their standard doctor-bladed counterparts. Reference (1) Kuang, Y.; Chen, C.; Kirsch, D.; Hu, L. Thick Electrode Batteries: Principles, Opportunities, and Challenges. Adv. Energy Mater. 2019 , 9 (33), 1901457. https://doi.org/10.1002/aenm.201901457.

Toward High Areal Energy and Power Density Electrode for Li-Ion Batteries via Optimized 3D Printing Approach.

Vertical-channel Hierarchically Porous 3D Printed Electrodes with Ultrahigh Mass Loading and Areal Energy Density for Li-ion Batteries

3D printing PEDOT-CMC-based high areal capacity electrodes for Li-ion batteries

3D‐Printed Microelectrodes with a Developed Conductive Network and Hierarchical Pores toward High Areal Capacity for Microbatteries

Preparation of lithium iron phosphate battery by 3D printing

Towards high-performance Li-ion batteries via optimized three-dimensional micro-lattice electrode architectures

3D-Printed Lithium-Ion Battery Electrodes: A Brief Review of Three Key Fabrication Techniques

Influence of Binders on Printability and Battery Performance of Thick 3D-Printed Positive Electrode for Li-Ion Batteries

Three-Dimensional Double-Walled Ultrathin Graphite Tube Conductive Scaffold with Encapsulated Germanium Nanoparticles as a High-Areal-Capacity and Cycle-Stable Anode for Lithium-Ion Batteries

3D Printing of Flexible Electrodes Towards Wearable Lithium Ion Battery

3D Architected Solid-State Lithium-Ion Battery

3D Printed Ordered Hierarchically‐Porous Electrodes for Developing High‐Performance Quasi‐Solid‐State Aqueous Nickel‐Iron Batteries

Integrating Aperiodic 3D Porous Electrodes into 3D Batteries through Spray‐Deposited Polymer Electrolytes

(Digital Presentation) Ultra-Thick Electrodes Utilizing Short Diffusion Path Via Novel Micro-Casting Process for Lithium-Ion Batteries

Design and 3D Printing of Interdigitated Electrode Structures for High-performance Full Lithium-ion Battery

3D Printed Electrodes for Solid-State Lithium Batteries

Sandwich, Vertical-Channeled Thick Electrodes With High Rate And Cycle Performance

Advances in Multi-Scale Design and Fabrication Processes for Thick Electrodes in Lithium-Ion Batteries

Direct ink writing preparation of LiFePO4/MWCNTs electrodes with high-areal Li-ion capacity

Stereolithography of 3D Sustainable Metal Electrodes towards High‐Performance Nickel Iron Battery

3D printing for rechargeable lithium metal batteries