Abstract:The isotopic composition of sulfur is a vital tracer used in the Earth and planetary sciences. In this study, the laser-and ICP-induced isotopic fractionation in S-rich minerals (sulfides and elemental S) with different matrices was investigated by using 257 nm femtosecond (fs) and 193 nm ArF excimer nanosecond (ns) laser ablation systems coupled to a Neptune Plus MC-ICP-MS. Compared to ns-LA-MC-ICP-MS, higher sensitivity (1.4-2.4 times) under similar instrumental conditions and better precision (similar to 1.6-fold) under the same signal intensity condition were achieved by fs-LA-MC-ICP-MS. In addition, a fs-laser provides less fluence and matrix dependent S isotopic fractionation, and more stable transient isotopic ratios compared to a ns-laser. Better results acquired by fs-LA-MC-ICP-MS were attributed to the smaller size of particles and less thermal effect produced by using the fs-laser, which were evidenced by the morphologies of the ablation craters and ejected aerosol particles of P-S-1 (the pressed powder pellet of IAEA-S-1) and PPP-1 (a pyrite single crystal from the Sukhoi Log deposit). The ICP-induced isotopic fractionation (matrix effect) was still found in fs-LA-MC-ICP-MS under the maximum sensitivity conditions. However, a significant reduction of the matrix effect was obtained under robust plasma conditions at a lower makeup gas flow rate (0.52-0.54 l min(-1)) relative to the maximum sensitivity condition (0.6 l min(-1)) for S isotope analysis. This could be ascribed to the particles that not only pass into the higher temperature ICP for a longer residence time at a lower makeup gas flow rate that resulted in more efficient vaporization of the particles, but also experience a more robust plasma induced by adding 4-6 ml min(-1) N-2 into the plasma. Furthermore, under the robust conditions, the results of six reference materials with different matrices obtained by fs-LA-MC-ICP-MS with non-matrix matched calibration with a spot size of 20-44 mm showed excellent agreement with the reference values (the accuracy of 0.01-0.15 parts per thousand for delta S-34 and 0.11-0.45 parts per thousand for delta S-33 and the precision of 0.16-0.40 parts per thousand (2 s) for delta S-34 and 0.35-0.78 parts per thousand (2 s) for delta S-33) and the mass-dependent fractionation line, validating the applicability of the proposed approach for providing high-quality in situ isotope data (delta S-33 and delta S-34) of sulfides and elemental sulfur at high spatial resolution using non-matrix matched analysis.

[A New Sample Fusion Technique for Quantitative Analysis of Major and Minor Elements in Sulfides with X-Ray Fluorescence Spectrometry and Laser Ablation Inductively Coupled Plasma Mass Spectrometry].

A Flux‐Free Fusion Technique for Rapid Determination of Major and Trace Elements in Silicate Rocks by LA‐ICP‐MS

Flux-free fusion technique using a boron nitride vessel and rapid acid digestion for determination of trace elements by ICP-MS

Determination of Trace Elements in Sulfide Samples by Inductively Coupled Plasma-Mass Spectrometry

Simultaneous Measurement of Sulfur and Lead Isotopes in Sulfides Using Nanosecond Laser Ablation Coupled with Two Multi-Collector Inductively Coupled Plasma Mass Spectrometers

Mapping of Sulfur Isotopes and Trace Elements in Sulfides by LA-(MC)-ICP-MS: Potential Analytical Problems, Improvements and Implications

In-situ Determination of Metallic Variation and Multi-Association in Single Particles by Combining Synchrotron Microprobe, Sequential Chemical Extraction and Multivariate Statistical Analysis.

A modified laser ablation‐isotope ratio mass spectrometry method for in situ analysis of sulfur isotope composition of sulfides

A Simple Method for the Preparation of Homogeneous and Stable Solid Powder Standards: Application to Sulfide Analysis by LA-ICP-MS

Simultaneous Determination of Major and Trace Elements in Fused Volcanic Rock Powders Using A Hermetic Vessel Heater and La-Icp-Ms

Calibration-free Elemental Analysis Combined with High Repetition Rate Laser-Ablation Spark-Induced Breakdown Spectroscopy

ON THE MODIFICATION FOR XRFS ANALYSIS OF IRON ORES WITH PREPARATION OF SAMPLE CUBES BY FUSION WITH MIXED FLUX

Accurate determination of sulfur isotopes (delta S-33 and delta S-34) in sulfides and elemental sulfur by femtosecond laser ablation MC-ICP-MS with non-matrix matched calibration

Quick and accurate LA-ICP-MS analyses of major and trace elements in basalt,coupled with glass fusion method by double iridium strip heater

Quantitative Analysis of Elemental Concentrations of Aluminum Alloys Using Calibration-Free Femtosecond Laser-Ablation Spark-Induced Breakdown Spectroscopy

Application of Fluorescent X Ray Fusion Method in Multi-Element Analysis on Furnace Slag

Application of Calibration-Free High Repetition Rate Laser-Ablation Spark-Induced Breakdown Spectroscopy for the Quantitative Elemental Analysis of a Silver Alloy.

Rapid Determination of Trace Element Compositions in Peridotites by LA‐ICP‐MS Using an Albite Fusion Method

Accurate determination of sulfur isotopes (δ33S and δ34S) in sulfides and elemental sulfur by femtosecond laser ablation MC-ICP-MS with non-matrix matched calibration

[Determination of Fe, Al, Ca, Ti, P and Cu in Silicon Metal by XRF].

The quantitative analysis of several metal elements in a solution by the confocal X-ray fluorescence thin-sample approach