Abstract:Background: Multi-comminuted, intra-articular fractures of the distal humerus still pose a challenge to modern orthopedics due to unsatisfactory treatment results and a high percentage (over 50%) of postoperative complications. When surgical treatment is chosen, such fractures are fixed using two plates with locking screws, which can be used in three spatial configurations: either parallel or one of two perpendicular variants (posterolateral and posteromedial). The evaluation of the fracture healing conditions for these plate configurations is unambiguous. The contradictions between the conclusions of biomechanical studies and clinical observations were the motivation to undertake a more in-depth biomechanical analysis aiming to indicate the weak points of two-plate fracture stabilization. Methods: Research was conducted using the finite element method based on an experimentally validated model. Three variants of distal humerus fracture (Y, λ, and H) were fixed using three different plate configurations (parallel, posterolateral, and posteromedial), and they were analyzed under six loading conditions, covering the whole range of flexion in the elbow joint (0–145°). A joint reaction force equal to 150 N was assumed, which corresponds with holding a weight of 1 kg in the hand. The biomechanical conditions of bone union were assessed based on the interfragmentary movement (IFM) and using criteria formulated by Steiner et al. Results: The IFMs were established for particular regions of all of the analyzed types of fracture, with distinction to the normal and tangential components. In general, the tangential component of IFM was greater than normal. A strong influence of the elbow joint's angular position on the IFM was observed, with excessive values occurring for flexion angles greater than 90°. In most cases, the smallest IFM values were obtained for the parallel plaiting, while the greatest values were obtained for the posteromedial plating. Based on IFM values, fracture healing conditions in particular cases (fracture type, plate configuration, loading condition, and fracture gap localization) were classified into one of four groups: optimal bone union (OPT), probable union (PU), probable non-union (PNU), and non-union (NU). Conclusions: No plating configuration is able to ensure distal humerus fracture union when the full elbow flexion is allowed while holding a weight of 1 kg in the hand. However, flexion in the range of 0–90° with such loadings is acceptable when using parallel plating, which is a positive finding in the context of the early rehabilitation process. In general, parallel plating ensures better conditions for fracture healing than perpendicular plate configurations, especially the posteromedial version.

Finite Element Analysis of Different Double-Plate Angles in the Treatment of the Femoral Shaft Nonunion with No Cortical Support Opposite the Primary Lateral Plate.

Improved anterolateral approach to treatment of terminal femoral fractures

Biomechanical assessment of single LISS versus double-plate osteosynthesis in the AO type 33-C2 fractures: A finite element analysis

Plate Configuration for Biological Reconstructions of Femoral Intercalary Defect - a Finite Element Evaluation.

Locking Plate Configuration for Biological Reconstructions at Diaphysis Following Femoral Large Segmental Defect – A Finite Element Evaluation of Orthogonal Versus Parallel

A Comparative Study of Two Treatment Methods for Comminuted Distal Femoral Fractures

Finite element analysis of a novel anatomical plate in posterolateral plateau fractures

Biomechanical comparison of two internal fixation methods for AO type A3 fractures of distal femur

Comparison of a Multidimensional Cross Locking Plate Versus a Locking Compression Plate for the Treatment of Femoral Shaft Nonunion: Finite Element Analysis

Lateral anatomic locking plate in combination with different medial plates in the treatment of comminuted metaphyseal distal femoral fractures: an animal experiment

Newly designed anterolateral and posterolateral locking anatomic plates for lateral tibial plateau fractures: a finite element study

Different modes of augmentative plating for femoral shaft nonunion after intramedullary nailing: a biomechanical comparison

Computational analysis of the biomechanical stability of internal fixation of the lateral tibial plateau fracture: A mechanical stability study

Augmentative Plating for Treatment of Nonunion of Femoral Shaft Fracture after Intramedullary Nailing: a Biomechanical Study

Importance of the Posterior Plate in Three‐Column Tibial Plateau Fractures: A Finite Element Analysis and Clinical Validation

Finite Element Analysis of Three Internal Fixations for the Posteromedial Split Fracture Fragment in Tibial Plateau Fractures

The impact of plate length, fibula integrity and plate placement on tibial shaft fixation stability: a finite element study

Weak Points of Double-Plate Stabilization Used in the Treatment of Distal Humerus Fracture through Finite Element Analysis

Failure Analysis of a Locking Compression Plate with Asymmetric Holes and Polyaxial Screws

Biomechanics and finite element analysis comparing posterior T-plates with LCP for fixation of posterolateral tibial plate fractures

The Study of Biomechanics and Clinical Anatomy on a Novel Plate Designed for Posterolateral Tibial Plateau Fractures via Anterolateral Approach