Abstract:Recently, sodium ion batteries (NIBs) gained increasing attention, because of its abundant reserves and relatively even geological distribution. However, the development of NIBs is greatly hampered because of the lack of appropriate active materials for both cathodes and anodes. Since the Na ion is ca. 55% larger than the Li ion, finding suitable host materials with sufficiently large interstitial space to accommodate sodium ions and to allow reversible and rapid ion insertion and extraction is very difficult. NASICON-type Na3V2(PO4)3 has recently been considered as a prospective cathode material for NIBs, because of its highly covalent 3D framework crystalline structure, high energy density (~400 Wh/kg) and good thermal stability. For anode materials, disordered carbon is particularly attractive because of their large interlayer distance and disordered structure that could accommodate sodium ions. Here, we briefly present porous carbon based electrodes for NIBs with excellent rate performance: (1) Carbon-coated nanosized Na3V2(PO4)3 embedded in the porous carbon matrix (abbreviated as CC-NVP@PCM); (2) Nitrogen-doped activated porous carbon fibers (ACFs); (3)Flexible free-standing porous carbon nanofibers (P-CNFs) with three-dimensional (3D) interconnected structure. The CC-NVP@PCM was prepared by using a facile soft-chemistry based method with post heat-treatment. It shows high rate performance (44 mAhg-1at 200C ). This ultrahigh rate performance is comparable to that of supercapacitor, but with much higher energy density. The ACFs were synthesized by pyrolysis of Ppy nanofiber precursor. It shows excellent capacity retention and extraordinary rate performance. The reversible capacity at 0.05 Ag-1 is 296 mAhg-1 and could still maintain as 72 mAg-1 at a current of 10 Ag-1. In case of the P-CNFs electrode prepared by electrospinning, it delivers a reversible capacity of 266 mAh.g-1 after 100 cycles at 0.2C, corresponding to 80.3 % of the initial charge capacity. When cycled at a current density as high as 500 mAg-1 (2C), it still delivers a reversible capacity of ~140 mAh.g-1after 1000 cycles. The improvement of electrochemical performance of these porous carbon based electrodes for NIBs is attributed to the special design and porous structure, which confined a variety of advantages: hierarchical porous channels enabling short transport length for ions and electrons, carbon coated structure resulting in low resistances, good mechanical properties leading to the excellent morphology stability.

Defect Sites-Rich Porous Carbon with Pseudocapacitive Behaviors As an Ultrafast and Long-Term Cycling Anode for Sodium-Ion Batteries

3D Interconnected and Multiwalled Carbon@MoS 2 @Carbon Hollow Nanocables as Outstanding Anodes for Na-Ion Batteries.

A Hierarchical N/S‐Codoped Carbon Anode Fabricated Facilely from Cellulose/Polyaniline Microspheres for High‐Performance Sodium‐Ion Batteries

Rational design of high nitrogen-doped and core-shell/mesoporous carbon nanospheres with high rate capability and cycling longevity for pseudocapacitive sodium storage

Defect‐Rich Soft Carbon Porous Nanosheets for Fast and High‐Capacity Sodium‐Ion Storage

Synergistic Engineering of Defects and Architecture in Co3O4@C Nanosheets Toward Li/Na Ion Batteries with Enhanced Pseudocapacitances

Heteroatom‐Doped Mesoporous Hollow Carbon Spheres for Fast Sodium Storage with an Ultralong Cycle Life

Nitrogen-doped 3D nanocarbon with nanopore defects as high-capacity and stable anode materials for sodium/lithium-ion batteries

High Capacity and Superior Rate Performances Coexisting in Carbon-Based Sodium-Ion Battery Anode

Surface engineered hollow Ni-Co-P@TiO2- nanopolyhedrons as high performance anode material for sodium storage

Electrodes for Sodium-Ion Batteries with Excellent Rate Performance Using Porous Carbon Networks

Sodium/Potassium‐Ion Batteries: Boosting the Rate Capability and Cycle Life by Combining Morphology, Defect and Structure Engineering

Tailoring 2D Heteroatom‐Doped Carbon Nanosheets with Dominated Pseudocapacitive Behaviors Enabling Fast and High‐Performance Sodium Storage

Na(+) intercalation pseudocapacitance in graphene-coupled titanium oxide enabling ultra-fast sodium storage and long-term cycling

Carbon-coated Na3V2(PO4)2F3 Nanoparticles Embedded in a Mesoporous Carbon Matrix As a Potential Cathode Material for Sodium-Ion Batteries with Superior Rate Capability and Long-Term Cycle Life

A Scalable Approach to Na4Fe3(PO4)2P2O7@carbon/expanded Graphite As Cathode for Ultralong-Lifespan and Low-Temperature Sodium-Ion Batteries

Design of coherent anode materials with 0D Ni3S2 nanoparticles self-assembled on 3D interconnected carbon networks for fast and reversible sodium storage

Rational Regulation of Defect-Rich Hierarchical Porous Carbon Nanosheets As Sustainable Anode Materials for Potassium-Ion Storage

Cagelike CoSe<sub>2</sub>@N-Doped Carbon Aerogels with Pseudocapacitive Properties as Advanced Materials for Sodium-Ion Batteries with Excellent Rate Performance and Cyclic Stability

Core/Double-Shell Structured Na3V2(PO4)2F3@C Nanocomposite As the High Power and Long Lifespan Cathode for Sodium-Ion Batteries

Sulfur Doped Ultra-Thin Anatase TiO2 Nanosheets/graphene Nanocomposite for High-Performance Pseudocapacitive Sodium Storage