Abstract:Total knee arthroplasty (TKA) is a cornerstone in addressing knee joint disorders, significantly enhancing patients' quality of life. However, despite technological advancements, a comprehensive understanding of the dynamic stresses experienced by knee prostheses during daily activities, particularly under rehabilitation interventions, remains elusive. This study aims to bridge this gap by employing numerical simulations and finite element analysis to elucidate these dynamic stresses and their interaction with rehabilitation protocols. A real-life knee replacement prosthesis model was meticulously constructed through coordinate measuring and 3D scanning, facilitating detailed finite element analysis in ANSYS Workbench version 17.1. Two distinct boundary conditions and loading scenarios were applied, with comparisons made between linear and nonlinear material assumptions. The simulation results using these different boundary condition methods revealed minimal differences. Specifically, at a knee angle of 0°, the relative stress error rate between the two boundary condition types was approximately 1 % (1.11 MPa and 1.099 MPa, respectively). At 15° and 90°, the error rates were 1.9 % and 0.56 %, respectively (10.275 MPa and 10.078 MPa at 15°; 10.275 MPa and 10.078 MPa at 90°). Given these minimal differences, the first type of boundary condition was adopted for the subsequent scenarios to enhance convergence efficiency in the analysis. Moreover, comparative analyses between linear and nonlinear material behaviors demonstrated acceptable agreement, offering insights into potential efficiency gains in simulation methodologies. Building on this foundation, an optimized tibial model was proposed, incorporating geometric alterations to the tray. Quantitative assessments revealed significant reductions, with von Mises stress decreasing by 23.35 % and equivalent strain by 17 % at a knee angle of 140°. Further evaluations at varying angles, including 60°, consistently showed positive influences on stress and strain. These quantitative findings not only contribute valuable insights into the mechanical behavior of knee prostheses but also provide tangible evidence for the efficacy of linear material behavior assumptions. The proposed optimized model exhibits promising potential for enhancing the design and performance of knee prostheses, particularly under critical loading conditions. In conclusion, these results underscore the importance of a nuanced understanding of knee prosthesis behavior during rehabilitation, offering a quantitative foundation for refining existing designs and informing the development of next-generation prostheses.

Evaluation of a Subject-Specific Musculoskeletal Modelling Framework for Load Prediction in Total Knee Arthroplasty.

Prediction of in vivo joint mechanics of an artificial knee implant using rigid multi-body dynamics with elastic contacts.

A subject-specific musculoskeletal model to predict the tibiofemoral contact forces during daily living activities

A Patient-Specific Wear Prediction Framework for an Artificial Knee Joint with Coupled Musculoskeletal Multibody-Dynamics and Finite Element Analysis

Computational Lower Limb Simulator Boundary Conditions to Reproduce Measured TKA Loading in a Cohort of Telemetric Implant Patients

Load application for the contact mechanics analysis and wear prediction of total knee replacement.

Numerical investigation of knee prosthesis stresses in daily activities: Insight into knee rehabilitation and Creation of a new optimal model

Prediction of Hip Joint Load and Translation Using Musculoskeletal Modelling with Force-Dependent Kinematics and Experimental Validation

Can TKA outcomes be predicted with computational simulation? Generation of a patient specific planning tool

Prediction of knee biomechanics with different tibial component malrotations after total knee arthroplasty: conventional machine learning vs. deep learning

Development and validation of a computational model of the knee joint for the evaluation of surgical treatments for osteoarthritis

Prediction of medial and lateral contact force of the knee joint during normal and turning gait after total knee replacement

Multiscale finite element musculoskeletal model for intact knee dynamics

Predicting Knee Joint Contact Forces During Normal Walking Using Kinematic Inputs with A Long-Short Term Neural Network

Effect of surgical parameters on the biomechanical behaviour of bicondylar total knee endoprostheses – A robot-assisted test method based on a musculoskeletal model

DEIT-Based Bone Position and Orientation Estimation for Robotic Support in Total Knee Arthroplasty-A Computational Feasibility Study

An Automated and Robust Tool for Musculoskeletal and Finite Element Modeling of the Knee Joint

On the prediction of tibiofemoral contact forces for healthy individuals and osteoarthritis patients during gait: a comparative study of regression methods

Surgical factors play a critical role in predicting functional outcomes using machine learning in robotic‐assisted total knee arthroplasty

A finite element analysis for predicting outcomes of cemented total knee arthroplasty

A novel computational workflow to holistically assess total knee arthroplasty biomechanics identifies subject-specific effects of joint mechanics on implant fixation