Abstract:Electrospinning is a simple and versatile technique for producing micro- and nanofibers. It has been shown that electrospun tissue engineering scaffolds mimic the structure of the extracellular matrix of human body tissues. These scaffolds can improve cell attachment behavior and subsequent cell proliferation and differentiation. On the other hand, due to their large surface area to volume ratio and porous morphology, electrospun micro- and nanofibers are potentially useful for the controlled release of therapeutic agents (drugs and therapeutic biomolecules) in human bodies. In this study, electrospinning of poly(L-lactic acid) (PLLA) nonwoven micro- and nanofibrous membranes was investigated. It is known that the morphology and size of a drug carrier could play very important roles in the drug release behavior. Therefore, in the present investigation, a comprehensive study on the fabrication parameters that could affect the morphology and diameter of PLLA fibers was conducted. For electrospinning, several parameters were associated with intrinsic properties of the polymer solution, such as PLLA intrinsic viscosity, polymer solution concentration and solvent used, while other parameters were related to the experimental setup and electrospinning environment, including applied voltage, working distance, needle size, feeding rate, etc. Among these parameters, some solution related factors were important for controlling the fiber diameter. The average fiber diameter decreased from 3.2 μm to 0.6 μm when N,N-dimethylformamide (DMF) was added into a solvent system. While using dichloromethane (DCM) as the solvent, the fiber diameter could vary between 1 μm to 8 μm using different PLLA solution concentrations. Different solvent systems could also affect the morphology of PLLA fibers. On the other hand, most of the apparatus and environment related parameters could help to improve the fiber morphology, but not very significantly. It was also found that the stability of electrospinning conditions may improve the uniformity of PLLA fiber diameter. When lower voltage was applied, although the average fiber diameter increased, the range of variation of fiber diameters decreased. This study shows that PLLA fibrous membranes with a controllable average fiber diameter ranging from 600 nm to 8 μm could be fabricated via electrospinning. These fibrous membranes have the potential as vehicles for the controlled release of therapeutic agents in tissue engineering.

Influence of the structure of poly (L-lactic acid) electrospun fibers on the bioactivity of endothelial cells: proliferation and inflammatory cytokines expression.

Impact of Substrate Geometry on Electrospun Fiber Deposition and Alignment

Influence of Layer-by-layer Assembled Electrospun Poly (L-Lactic Acid) Nanofiber Mats on the Bioactivity of Endothelial Cells

Preparation of Magnetically Electrospun Aligned and Conductive Poly(Lactic-Co-Glycolicacid) Fibers and Their Properties

Biodegradable Micro- and Nanofibers Fabricated Through Electrospinning for Tissue Engineering and Controlled Release Applications

The Influence of Several Chief Parameters in Electrospinning on the Morphology and the Fiber Diameter of PLGA Fiber Scaffolds

Preparation and Cytocompatibility of Plga Scaffolds with Controllable Fiber Morphology and Diameter Using Electrospinning Method

Biocompatibility, Alignment Degree and Mechanical Properties of an Electrospun Chitosan-P(Lla-Cl) Fibrous Scaffold

The effect of poly (L-lactic acid) nanofiber orientation on osteogenic responses of human osteoblast-like MG63 cells.

Electrospun Core-Sheath Fibers for Integrating the Biocompatibility of Silk Fibroin and the Mechanical Properties of PLCL

A Comparative Study on Conventional Electrospinning and Emulsion Electrospinning of PLLA Nanofibers

The Influence Of Type-I Collagen-Coated Plla Aligned Nanofibers On Growth Of Blood Outgrowth Endothelial Cells

Impact of uniaxial cyclic stretching on matrix-associated endothelial cell responses

The Influence of Fiber Diameter of Electrospun Poly(lactic Acid) on Drug Delivery

Improvement of Cytocompatibility of Electrospinning PLLA Microfibers by Blending PVP.

Cell Adhesive and Growth Behavior on Electrospun Nanofibrous Scaffolds by Designed Multifunctional Composites

Improving cytoactive of endothelial cell by introducing fibronectin to the surface of poly L-Lactic acid fiber mats via dopamine.

Modeling and fabrication of electrospun polymer nanofibers with tailored architectures for tissue engineering scaffold applications

Biocompatibility of poly-L-lactic acid/chitosan electrospun nanofiber scaffold and rabbit endothelial progenitor cells

Fabrication of Aligned, Porous and Conductive Fibers and Their Effects on Cell Adhesion and Guidance

Stiffness of Aligned Fibers Regulates the Phenotypic Expression of Vascular Smooth Muscle Cells