Abstract:Poly(methyl methacrylate) (PMMA) is a commonly used material, as it is biocompatible and relatively cheap. However, its mechanical properties and weak antibiofilm activity are major concerns. With the development of new technology, 3D-printed resins are emerging as replacements for PMMA. Few studies have investigated the antibiofilm activity of 3D-printed resins. Therefore, this study aimed to investigate the antibiofilm activity and surface roughness of a 3D-printed denture base resin modified with different concentrations of zirconium dioxide nanoparticles (ZrO2 NPs). A total of 60 resin disc specimens (15 × 2 mm) were fabricated and divided into six groups (n = 10). The groups comprised a heat-polymerized resin (PMMA) group, an unmodified 3D-printed resin (NextDent) group, and four 3D-printed resin groups that were modified with ZrO2 NPs at various concentrations (0.5 wt%, 1 wt%, 3 wt%, and 5 wt%). All specimens were polished using a conventional method and then placed in a thermocycler machine for 5000 cycles. Surface roughness (Ra, µm) was measured using a non-contact profilometer. The adhesion of Candida albicans (C. albicans) was measured using a fungal adhesion assay that consisted of a colony forming unit assay and a cell proliferation assay. The data were analyzed using Shapiro-Wilk and Kruskal-Wallis tests. A Mann-Whitney U test was used for pairwise comparison, and p-values of less than 0.05 were considered statistically significant. The lowest Ra value (0.88 ± 0.087 µm) was recorded for the PMMA group. In comparison to the PMMA group, the 3% ZrO2 NPs 3D-printed group showed a significant increase in Ra (p < 0.025). For the 3D-printed resins, significant differences were found between the groups with 0% vs. 3% ZrO2 NPs and 3% vs. 5% ZrO2 NPs (p < 0.025). The highest Ra value (0.96 ± 0.06 µm) was recorded for the 3% ZrO2 NPs group, and the lowest Ra values (0.91 ± 0.03 µm) were recorded for the 0.5% and 5% ZrO2 NPs groups. In terms of antifungal activity, the cell proliferation assay showed a significant decrease in the C. albicans count for the 0.5% ZrO2 NPs group when compared with PMMA and all other groups of 3D-printed resins. The group with the lowest concentration of ZrO2 NPs (0.5%) showed the lowest level of C. albicans adhesion of all the tested groups and showed the lowest Candida count (0.29 ± 0.03). The addition of ZrO2 NPs in low concentrations did not affect the surface roughness of the 3D-printed resins. These 3D-printed resins with low concentrations of nanocomposites could be used as possible materials for the prevention and treatment of denture stomatitis, due to their antibiofilm activities.

Antibacterial Activity, Cytotoxicity and Mechanical Behavior of Nano-Enhanced Denture Base Resin with Different Kinds of Inorganic Antibacterial Agents.

Effect of silver-supported materials on the mechanical and antibacterial properties of reinforced acrylic resin composites

Effect of different inorganic antibacterial agent on bacteria adhesion of nano-enhanced polymethymethacrylate denture base resin

[Effects of Tetrapod-Like Zinc Oxide Whiskers Incorporation on Antibacterial Activity of Composite Resin].

Antimicrobial activity of poly methyl methacrylate denture base with Ag-nano-TiO_2 in vitro

Tetrapod-like Zinc Oxide Whisker Enhancement of Resin Composite

Antimicrobial properties, cytotoxicity, colour and mechanical behavior of light-cured resin composites containing modified Novaron

Assessing the physico-mechanical, anti-bacterial, and anti-demineralization properties of orthodontic resin composite containing different concentrations of photoactivated zinc oxide nanoparticles on Streptococcus mutans biofilm around ceramic and metal orthodontic brackets: An ex vivo study

Effects of Tetrapod-Like Zinc Oxide Whisker Incorporation on the Mechanical Properties of Composite Resin

[Effects of Three Different Zinc Oxide Incorporation on the Antibacterial Activity Against Streptococcus Mutans of Composite Resin].

Development of antibacterial dual-cure dental resin composites via tetrapod-shaped zinc oxide incorporation

Antibiofilm Activity of 3D-Printed Nanocomposite Resin: Impact of ZrO2 Nanoparticles

Hybrid Effects of Zirconia Nanoparticles with Aluminum Borate Whiskers on Mechanical Properties of Denture Base Resin Pmma

The Mechanical and Antibacterial Properties of Boron Nitride/Silver Nanocomposite Enhanced Polymethyl Methacrylate Resin for Application in Oral Denture Bases

Antibacterial effect of novel dental resin composites containing rod-like zinc oxide

The effects of nano-silver loaded zirconium phosphate on antibacterial properties, mechanical properties and biosafety of room temperature curing PMMA materials

Effect of zinc oxide/graphene oxide nanocomposites on the cytotoxicity, antibacterial and mechanical properties of polymethyl methacrylate

Enhanced Bacterial and Biofilm Adhesion Resistance of ALD Nano-TiO2 Coatings Compared to AO Coatings on Titanium Abutments

A study of denture base Ag-carrying zeolite/PMMA antibacterial composite material

Mechanical and Antimicrobial Properties of Boron Nitride/Methacrylic Acid Quaternary Ammonium Composites Reinforced Dental Flowable Resins

An In Vitro Study Comparing the Antibacterial and Mechanical Properties of Zinc Oxide-Based Nanofillers in Orthodontic Adhesives for White Spot Lesion Prevention in Fixed Orthodontic Therapy