Abstract:The prediction of the macrosegregation in large ingot is a challenging issue due to the size of the ingots and the variety of the phenomena to be accounted for, such as thermal-solutal convection of the liquid, equiaxed grain motion, evolution of grain morphology by suitably considering a coupled grain growth model in the macroscopic solidification model, the columnar-to-equiaxed transition (CET), and shrinkage, etc.. Each of these phenomena is very important to the solidification pattern, while it is impossible for one model to consider all the phenomena together until now due to the computation power limited. Thus, the model capability and computational cost should be counterpoised for the simulation of large ingot. In this work, a mixed three-phase (simplified dendritic-equiaxed, columnar and liquid) solidification model is described based on Eulerian-Eulerian approach and volume average method. The model considers the thermosolutal buoyancy flow, the movement of equiaxed crystal, and the capture of the equiaxed crystals by growing columnar tree trunks. The mechanical interaction and impingement between columnar and equiaxed crystals are considered which give the capability to predict CET. In order to enhance the model capability without increasing the computational cost significantly, a simplified method is proposed to consider the dendritic of equiaxed crystal. This model is employed to simulate the formation process of macrosegregation for two different steel ingots (3.25 and 25 t). The general macrosegregation pattern predicted by this model includes the cone of negative segregation in the bottom of ingot, quasi-A-segregation in the columnar zone, and positive segregation in the top region, which are quite similar to the classic knowledge. The CET zones are also predicted. Although there is still some quantitative discrepancy, the macrosegregation distribution predicted by this model is quite similar to the experimental measurements. The non-globular equiaxed three-phase mixed model results are compared with theglobular-equiaxed mixed three-phase model ones, which indicated that for large ingots the equiaxed dendritic structure plays an important role in liquid flow and it affects final characteristic of macrosegregation. It is predicted successfully that a negative segregation zone would be formed in the upper region due to the formation of a local mini-ingot and the subsequent sedimentation and piling up of equiaxed grains within the mini-ingot.

Four-Phase Dendritic Model for the Prediction of Macrosegregation, Shrinkage Cavity, and Porosity in A 55-Ton Ingot

Multiphase Model for the Prediction of Shrinkage Cavity, Inclusion and Macrosegregation in a 36-Ton Steel Ingot

Dendritic Model for Macrosegregation Prediction of Large Scale Castings

Influence of Dendritic Morphology on the Calculation of Macrosegregation in Steel Ingot

Simulation of Macrosegregation and Shrinkage Cavity in an Al-4.5 Wt Pct Cu Ingot Using a Four-Phase Model

A COLUMNAR & NON-GLOBULAR EQUIAXED MIXED THREE-PHASE MODEL BASED ON THERMOSOLUTAL CONVECTION AND GRAIN MOVEMENT

Modelling of Ingot Size Effects on Macrosegregation in Steel Castings

Simulation of Macrosegregation in a 36-T Steel Ingot Using a Multiphase Model

Simulation of Macrosegregation in a 2.45-Ton Steel Ingot Using a Three-Phase Mixed Columnar-Equiaxed Model

Numerical Simulation of A-Segregation Evolution in a 55-Ton Ingot Using Four-Phase Solidification Model

Modelling of Inclusion Effects on Macrosegregation in Solidifying Steel Ingot with a Multi-phase Approach

Three-Dimensional Simulation of Macrosegregation in a 36-Ton Steel Ingot Using a Multicomponent Multiphase Model

Multiphase Modeling of Macrosegregation Formation in Steel Ingot

Experimental and Numerical Study of Macrosegregation in a 160 Steel Ingot

Numerical Simulation of Macrosegregation in a 535 Tons Steel Ingot with a Multicomponent-Multiphase Model

Numerical Simulation of Macrosegregation in Steel Ingots Using A Two-Phase Model

Finite Element Modeling of Macrosegregation Coupled with Shrinkage Cavity in Steel Ingots Using Arbitrary Lagrangian-Eulerian Model

Using a Three-Phase Mixed Columnar-Equiaxed Solidification Model to Study Macrosegregation in Ingot Castings: Perspectives and Limitations

Modelling Macrosegregation in a 2.45 Ton Steel Ingot

Three-dimensional simulation of thermosolutal convection and macrosegregation in steel ingots

A review on prediction of casting defects in steel ingots: from macrosegregation to multi-defect model