Abstract:The fabrication, transfer, and storage of a highly enriched isotopic target is very much crucial because of air gases and moistures being chemically active at room temperature. One must limit the amount of time that the target surface is exposed to the atmosphere during the transfer of air sensitive targets. The highly interactive targets are not easy to store for longer time and demand an in-vacuum transfer facility. Getting an alternative technique to remove all such imperative is a need of the hour specially for the nuclear physics community, more particularly for reaction dynamic studies of fission fragment mass distribution induced by stable and radioactive ion beams. Highly enriched materials are rare and very expensive, so an effective and highly efficient technique is needed to deal with such materials. Here, an attempt has been made to fabricate 96.63% enriched thin targets of 176 Yb by evaporation techniques enabling ≈129.1μg/cm2 thickness with a ≈25.93μg/cm2 carbon backing to increase its stability and durability. Numerous trials have been performed using natural Yb to optimize the evaporation setup and associated growth parameters for efficient Yb isotope deposition with thin film deposition unit and diffusion pump based coating unit at Inter University Accelerator Centre (IUAC), New Delhi. Thickness and elemental composition of the targets have been analyzed using characterization techniques such as X-ray diffraction, α -energy loss technique, Rutherford backscattering spectroscopy and energy dispersive X-ray spectroscopy. Essentially no significant impurities are found by these measurements, describing high purity and robustness of the fabricated targets. During the nuclear experiments, 30 Si and 16 O beams of intensity of the order of ≈ 10 10 particles per second were bombarded on the targets for 5-6 days and no ill effects on the target sustainability were observed. Isotopic abundance of the target has been obtained experimentally, which ensured the isotopic purity of the target required for the reaction studies. This article will admire our readers about the qualitative nature of the fabrication technique, measurement and characterization citing valuable insights, aiding in a comprehensive understanding of their quality.

Fabrication of 197 Au-backed Silicon target for In-beam Gamma-ray spectroscopy experiment

Fabrication of 208 Pb and 193 Ir targets on Al–backing using high/ultra-high vacuum deposition technique for low-energy nuclear reaction experiments

Fabrication and characterization of highly enriched thin 176 Yb targets for the reaction dynamic studies on fission mass distribution

Germanium Doping of Si Substrates for Improved Device Characteristics and Yield

Fabrication of $^{108}$Cd target for the astrophysical p-process studies

Lithium fluoride (LiF) target preparation for nuclear physics experiment

Simulation of Material Sputtering and Gallium Implantation during Focused Ion Beam Irradiation of a Silicon Substrate

Production and purification of molecular 225Ac at CERN-ISOLDE

Rate-Dependent Evolution of Microstructure and Stress in Silicon Films Deposited by Electron Beam Evaporation

Target fabrication for laser-ion acceleration research at the Technological Laboratory of the LMU Munich

Exploration of Methods to Remove Implanted $^{210}$Pb and $^{210}$Po Contamination from Silicon Surfaces

Direct atomic fabrication and dopant positioning in Si using electron beams with active real time image-based feedback

Naturally occurring $^{32}$Si and low-background silicon dark matter detectors

GEANT4 simulation of cyclotron radioisotope production in a solid target

Preparation of Silver and Silver-backing self-supported thin targets by high vacuum evaporation

Cryomilling of Isotope-Enriched Ti Powders for HIVIPP Deposition to Manufacture Targets for Nuclear Cross Section Measurement

Preparation and Characterization of Thin Arsenic Targets for Stacked-Target Experiments

Non-stoichiometric Silicon Nitride for Future Gravitational Wave Detectors

Ag Out-Surface Diffusion in Crystalline SiC with an Effective SiO2 Diffusion Barrier

Porous silicon carbide and aluminum oxide with unidirectional open porosity as model target materials for radioisotope beam production

Depositing a Titanium Coating on the Lithium Neutron Production Target by Magnetron Sputtering Technology