Molecular Dynamics Simulation Study on the Occurrence of Shale Oil in Hybrid Nanopores

Yujia Fang,Zhongxiao Li,Erlong Yang,Mingyu Sha,Shuling Song
DOI: https://doi.org/10.3390/molecules29020312
IF: 4.6
2024-01-09
Molecules
Abstract:The molecular dynamics simulation was used to simulate the influence of the composite wall stacking effect on shale oil occurrence. The kerogen-illite heterogeneous wall pore model was established to study the effects of temperature, pore size, and wall component ratio on the adsorption ratio and diffusion capacity of shale oil. The calculation results show that the fluid density distribution in the hybrid nanopore is not uniform. When the pore size increases, the proportion of the first adsorption layer to the total adsorption amount decreases rapidly, and the phenomenon of the "solid-like layer" of shale oil in small pores is more obvious. In addition, increases in temperature have little effect on the density peak of the first adsorption layer. With increases in organic matter content in the shale pore model, the diffusion coefficient of fluid decreases gradually, along with adsorption capacity. The influence of the irregular arrangement of kerogen molecules on the adsorption of shale oil is greater than the influence of surface roughness caused by illite on the adsorption.
chemistry, multidisciplinary,biochemistry & molecular biology
What problem does this paper attempt to address?
This paper primarily explores the state of shale oil in mixed nanopores and conducts molecular dynamics simulation studies. Specifically, the research aims to understand the adsorption behavior and diffusion capacity of shale oil in composite pores composed of organic matter (mainly kerogen) and illite (a type of clay mineral). ### Research Background and Objectives - **Research Background**: Shale oil is an unconventional oil and gas resource stored in source rock shale, with vast reserves and widespread distribution. Shale oil mainly exists in nanopores in the form of adsorption or free state. Understanding the behavior of shale oil in these tiny pores is crucial for improving the extraction efficiency of unconventional oil and gas resources. - **Research Objectives**: - Establish a kerogen-illite heterogeneous pore model to study the effects of temperature, pore size, and wall composition ratio on the adsorption rate and diffusion capacity of shale oil. - Explore the state patterns of shale oil in different pore sizes, including the formation and thickness of adsorption layers, density distribution characteristics, etc. - Analyze the differences in diffusion characteristics of shale oil molecules along the pore wall surface and parallel to the pore wall surface. ### Main Findings - In composite nanopores, the fluid density distribution of shale oil is uneven. As pore size increases, the proportion of the first adsorption layer to the total adsorption amount rapidly decreases, and the phenomenon of "solid layer" of shale oil in small pores is more evident. - The increase in temperature has little effect on the density peak of the first adsorption layer. - As the organic content in the pore model increases, the diffusion coefficient of the fluid gradually decreases, and the adsorption capacity also decreases. - The irregular arrangement of kerogen molecules has a greater impact on shale oil adsorption than the surface roughness of illite. - Under specific pressure and temperature conditions, the mass density distribution of shale oil in 5.36 nm pores shows two adsorption peaks, indicating the presence of a solid or "solid layer." The proportion of the adsorption phase is 31.25%, and the thickness of the two adsorption layers is about 0.5 to 0.6 nm. - The mean square displacement of shale oil molecules along the pore wall surface direction is significantly higher than that perpendicular to the pore wall surface direction, indicating that shale oil molecules mainly diffuse along the direction parallel to the pore wall. - Changes in pore size significantly affect the form of shale oil. In small pores less than 8.88 nm, shale oil is greatly influenced by pore wall forces, forming two adsorption layers; while in large pores greater than 8.88 nm, a free-flowing fluid region appears in the center, and four adsorption layers form on both sides of the pore wall. Through these research results, the authors provide a theoretical basis for the state of shale oil in composite pores and offer valuable reference information for further improving shale oil extraction efficiency.