Abstract:In this paper, a model of flood area display and damageevaluation is discussed, which adopts seed spread algorithm to calculate and visualize flood area based on a DEM data set and under the condition of a given water level of flood. The raster image containing flood area is overlaid with raster data converted from thematic vector maps such as land-use map and related to other socio-economic data, and then quantitative evaluation of flood damage is achieved. There are two different cases, the so-called “non-source flood” and “source flood”, for determining flood area based on DEM and under the given water level condition. Non-source flood corresponds to the case with well-distributed and large-area rainfall where all the low-lying land may have a flood disaster, and in this case all the points with elevations below the given water level should be included in the flood area. The “source flood” is the case of flood (e.g. from bank burst) flushing through the surrounding lands that needs to consider “ci rculating” condition. Because flood may be obstructed by ring structures or high lands, thus it can only cover the place where it flows and reaches. One of the computer processing methods suitable for source flood is the seed-spread algorithm. The principle of this method is to select a representative pixel as a seed and to examine its contiguous pixels outward along 4 or 8 directions. The pixels, contiguous to it and meeting the given conditions, become seeds, and then contiguous pixels to the new seeds will be examined in the same way. This process repeats until an aggregation of the pixels which meet the given conditions on a certain plane are obtained. Adopting seed spread algorithm for source-flood area calculation is just to achieve an aggregation of pixels, which satisfies the connectivity requirement and the given conditions of water level. The initial position of seed pixel should usually be selected on the characteristic points, e.g. adjacent to a reservoir dam or stream boundary. The precision of flood area calculation is mainly determined by spatial resolution of the DEM, the area on the ground is represented by each pixel; whereas the accuracy of flood area calculation, to a great extent, is dependent on the preci sion of the DEM's pixel value or elevation.Once the area below the flood water level has been calculated, the flood damage evaluation can be calculated by overlaying the flood range with thematic maps and by relating to other socio-economic data. All thematic maps were converted to raster data because algorithm of the overlay analysis implemented in raster format is relatively simple and computing is fast. In order to improve accuracy of the flood damage evaluation it is necessary to accurately register and georefer all raster layers before overlay analysis. The calculation results of flood damage evaluation are generally represented by tabulation, which is a kind of classified statistics of flood damage data, e.g. a table representing total area of every land-use type in different administrative divisions. The results of flood area calculation and damage evaluation can also be visually and dynamically provided in the forms of graph, image, 3D or virtual reality. The model has been successfully applied in the “Zhejiang Provincial Water Conservancy Management System” developed for a national project.

Management System for Dam-Break Hazard Mapping in a Complex Basin Environment

According to the standards and requirements of flood risk mapping guidelines set by the Ministry

Modeling of Dike-Break Induced Flood Routing Process and Flood Risk Assessment in Detention Basins

Enhancing Flood Risk Assessment and Mitigation Through Numerical Modeling: A Case Study

Dam-break Flood Loss Assessment in Hurricane-Prone Regions

A GIS-based Method for Flooded Area Calculation and Damage Evaluation

Dynamic flood risk mapping and development of a management system for Yangcheng & Dianmao District

A GIS-based 3D Visual Simulation System for Flood Protection

Study of the Comprehensive Risk Analysis of Dam-Break Flooding Based on the Numerical Simulation of Flood Routing. Part I: Model Development

A GIS Based Model for Calculating of Flood Area

Comparative Analysis and Risk Assessment of Dam-Break Floods: Taking Pingshuijiang Reservoir As an Example

Flood Prevention Management Information System for Qingdao City's Daguhe River Basin

Dynamic 3D Simulation of Flood Risk Based on the Integration of Spatio-Temporal GIS and Hydrodynamic Models

Numerical Simulation for Dam-Break Flood in Hurricane-Prone Regions

Analyzing Inundation Extent in Small Reservoirs: A Combined Use of Topography, Bathymetry and a 3D Dam Model

Development of a model-based flood emergency management system in Yujiang River Basin, South China

Dike-Break Induced Flood Simulation and Consequences Assessment in Flood Detention Basin

Automatic Mapping of a Reservoir Flood Risk Map Using GIS Technology

Simulation research of urban dam break flood based on MIKE FLOOD model

Emergency evacuation planning against dike-break flood: a GIS-based DSS for flood detention basin of Jingjiang in central China

The Research On 3d Visualization System Of Dam-Break Flood Routing Based On Google Earth