Abstract:Abstract Cupronickel alloys have found widespread use in various applications such as heat exchangers, refrigeration systems, equipment, pumps, and pipes. However, the inherent structure of cupronickel alone may not be able to withstand certain aggressive environments effectively. To address this issue, the mechanical properties and corrosion resistance of cupronickel alloys can be enhanced by carefully selecting the appropriate alloying compositions. The addition of nano chromium (20 nm) has been proposed as a means of designing cupronickel alloys with improved performance. In the present study, corrosion and erosion–corrosion behaviors of cupronickel 70/30 alloys produced by the casting method without and with three different additions of nano Cr (1, 1.2, and 1.5 wt%) were investigated. The prepared specimens were subjected to electrochemical tests in 3.5 wt% sodium chloride solutions to evaluate their corrosion behavior. Additionally, an erosion–corrosion test was conducted at an impact angle of 90°, using a slurry solution containing 1 wt% SiO 2 sand in 3.5 wt% NaCl solution as the erodent. The specimens were comprehensively characterized using scanning electron microscopy, energy-dispersive X-ray spectroscopy, and X-ray diffraction techniques. The surfaces of the alloy specimens exhibited superficial attacks, but no pits were observed. Moreover, the surfaces developed a greenish coloration. The electrochemical tests conducted using saline solution revealed that the corrosivity of the cupronickel alloy with nano chromium addition varied from moderate to low, depending on the selected concentration. Despite undergoing corrosion in the saline environment, the modified cupronickel alloys demonstrated good resistance to this corrosive process. Therefore, they can be considered suitable for use in highly aggressive environments, such as in seawater capture systems. The erosion–corrosion test results indicated that the addition of nano chromium significantly enhanced the resistance of the specimens to erosion–corrosion. At 1.5 wt% Cr, the erosion–corrosion rate was reduced by 99.27%.

Corrosion Resistance Behavior of Gradient Microstructure Induced by Punching Deformation and Recovery Treatment on Cupronickel Alloy Surface

Electrochemical corrosion behavior of nanocrystalline copper bulk

Corrosion Resistance of a Gradient Surface with Cr Alloying on Low-Carbon Steel

Alloying induced by severe deformation and recovery treatment on low-carbon steel surface

Micro/nanostructure high strength and high conductivity CuCrZr alloy prepared through equal channel angular pressing and aging treatment

A study of the corrosion behavior of AZ31 Mg alloy in depth direction after surface nanocrystallization

Characterization of microstructural evolution and mechanical properties of Cu-Ni-Cr alloys deformed by ECAP

Influences of Grain Size on Electrochemical Corrosion Behaviors of Nickel-Based Alloy 718

Preparation of Gradient Nanostructured Cu–Al Alloy Matrix and Evolution Microstructure and Properties

Corrosion resistance of duplex and gradient CrNx coated H13 steel

Corrosion behavior and strengthening mechanism of Ni-Cu alloy coating on Nd-Fe-B magnets

A Study on the Influence of the Electroplating Process on the Corrosion Resistance of Zinc-Based Alloy Coatings

Enhanced Corrosion Resistance of a Cu10Ni Alloy in a 3.5 Wt% NaCl Solution by Means of Ultrasonic Surface Rolling Treatment

Role of gradient nanograined surface layer on corrosion behavior of aluminum 7075 alloy

Microstructure Evolution of As-Cast Nickel Aluminum Bronze under Electropulsing

Influence of nano chromium addition on the corrosion and erosion–corrosion behavior of cupronickel 70/30 alloy in seawater

Electrochemical behavior and electro-crystallization mechanism of Cu-Ni/Nano-Al 2 O 3 coating with a deposition current density dependence

Effect of Stress-Temperature Coupling on Gradient Alloying Induced by Punching Severe Deformation

Anodic electrochemical behaviors of Inconel 718 and Rene 65 alloys in NaNO 3 solution

GRAIN SIZE EVOLUTION, MECHANICAL AND CORROSION BEHAVIOUR OF PRECIPITATE STRENGTHENED Cu-Ni ALLOY

Influence of Milling–Electrochemical Polishing on Corrosion Resistance of NiTi Shape Memory Alloy