Abstract:Rechargeable lithium-ion batteries as the main energy storage equipment should possess high power density, excellent reversible capacity, and long cycle life. However, due to the high cost and dendrites growth of Li, searching for non-Li-ion batteries is urgent. Compared to lithium, magnesium has abundant resources, smaller ionic radius, and high energy density. Therefore, magnesium-ion batteries (MIBs) can act as the next generation metal-ion batteries. Two-dimensional materials based on Be or B element acting as the anode of metal-ion batteries always exhibit high theoretical storage capacity. Using first-principles calculations, we systematically explore the potential of BeB 2 as MIBs anode. The optimized BeB 2 monolayer structure shown in Fig. 1a consists of two atomic layers, where each Be atom is coordinated with six B atoms, and each B atom is coordinated with three Be atoms. The lattice constants are a = b = 3.037 Å with a thickness of 0.554 Å. From the phonon spectrum calculations, the absence of imaginary modes indicates the dynamic stability of BeB 2 monolayer. The presence of a Dirac cone further suggests the excellent conductivity (Fig. 1b). Three stable adsorption sites (Be 1 : Top of Be atoms. Be 2 and B 2 : Bottom of Be and B atoms) are labeled in the Fig. 1a. Taking symmetry into account, we consider three pathways to evaluate the migration of Mg atom on BeB 2 monolayer (Fig. 1c). The corresponding lowest diffusion energy barrier is 0.04 eV along Path III. The stable configuration with the maximum adsorption Mg concentration is shown in Fig. 1d, which generates a theoretical capacity of 5696 mAhg -1 . The calculated average open-circuit voltage is 0.33V. Based on ab initio molecular dynamics simulations, the total energy of BeB 2 with Mg adsorbed fluctuates within a narrow range, suggesting that BeB 2 can sustain structural stability after the storage of Mg at room temperature (Fig.1e). Finally, for practical application, we investigate the adsorption and diffusion behavior of Mg on bilayer BeB 2 . Three configurations are considered: AA stacking (overlapping of Be atoms in upper layer with Be atoms in lower layer), AB stacking (overlapping of Be atoms in upper layer with B atoms in lower layer), and AC stacking (overlapping of Be atoms in upper layer with B-B bonds in lower layer). The most stable configuration is AB stacking (shown in Fig. 1f) with the interlayer space of 3.12 Å and the binding energies of -120.97 meV/atom. Compared to the BeB 2 monolayer structure, the adsorption energy of Mg is -2.24 eV for Be 1 , -1.38 eV for B 5 site, and -1.90 eV for B 4 site, while the lowest diffusion energy barrier is 0.13 eV along the path of B 5 -Be 3 -B 5 . Therefore, based on the above-mentioned properties, we believe BeB 2 monolayer can act as an excellent MIBs anode material.

Monolayer Black Phosphorus As Potential Anode Materials for Mg-ion Batteries

Theoretical prediction of Be2B monolayer as an ultra-high performance anode material for magnesium-ion batteries

Theoretical study of BeB 2 monolayer as anode material for magnesium ion battery

A First-Principles Study of Monolayer and Heterostructure Antimonene As Potential Anode Materials for Magnesium-ion Batteries

Theoretical Prediction of Anode Materials in Li-Ion Batteries on Layered Black and Blue Phosphorus

Graphene-like BGe Monolayer as Anode Material for Metal-ions Batteries: Computational Predictions

Water-Activated VOPO4 for Magnesium Ion Batteries

A novel two-dimensional monolayer MB4(M = Cr, Mo, W) MBenes as a high-performance anode material for Mg-ion batteries

Potential Application of 2D Haeckelite MoS2 as an Anode Material for Mg Ion Batteries

The Two-Dimensional Functionalized MBenes Mg2B3T (T=O, H, and F) Monolayers as Anode Material for High-Performance K-ion Batteries

First-Principles Study of Black Phosphorus As Anode Material for Rechargeable Potassium-Ion Batteries

Computational investigation of 2D 3d/4d hexagonal transition metal borides for metal-ion batteries

First principles theoretical of designing Sandwich-like Metallic BP4 Monolayer as Anode for Alkali Metal-ion Batteries

1T-MoS2 monolayer as a promising anode material for (Li/Na/Mg)-ion batteries

Pristine and Ti- or Al-doped B 3 CN 4 nanosheets as efficient anodes for Mg-ion batteries: A DFT study

Rational design of h‐AlC monolayer as anode material for Mg‐ion battery: A DFT study

First-principles investigation of Boron-doped graphene/MoS2 heterostructure as a potential anode material for Mg-ion battery

Detailed Structural and Electrochemical Comparison between High Potential Layered P2-NaMnNi and Doped P2-NaMnNiMg Oxides

Metallic Penta-BN2 Monolayer: A Novel Platform for Non-Lithium-ion Batteries with High Capacity and Splendid Cyclicity

Half‐Metallic PN2 Monolayer as High‐performance Anode Material for Metal Ion (Li, Na and K) Batteries: A First‐Principles Study

High-capacity, fast-charging and long-life magnesium/black phosphorous composite negative electrode for non-aqueous magnesium battery