Abstract:This study investigates the moisture absorption characteristics of the ULTEM® 9085 filament and how the uptake concentration affects the quality of material extrusion manufactured 3-D parts. The filament was exposed to humidity conditions to achieve various moisture concentrations (0, 0.05, 0.1, 0.16, 0.4 and 0.8 wt.%) and corresponding printed parts were evaluated for mechanical performance using tensile test dogbones. The rate of transport was modeled by Fickian diffusion and diffusion coefficients were obtained for various exposure conditions. Moduli, strain to failure and ultimate strength were evaluated in the XY (flat horizontal) and ZX(vertical) direction relative to the build plate orientation. Image analyses of cross-sections as well as their corresponding fracture surfaces were evaluated for consolidation, porosity distribution and failure behavior. Mechanical test data showed a significant decrease in tensile strength (>60%) and failure strain (>50%) over the range of filament moisture levels investigated. A decrease in failure strain of 41% was observed with moisture levels as low as 0.16%. This degradation was especially sensitive in parts printed in the vertical direction, which resulted in an ultimate failure strain of only 1%. The changes in mechanical performance are believed to be due to a combination of entrapped volatiles resulting in increased porosity at higher moisture levels as well as moisture induced pseudo-crosslinking at lower concentrations. Optical micrographs showed that specimens with 0.16% moisture or greater were filled with observable porosity and increased surface roughness. The rheological behavior of extruded material indicated plasticization as evidenced by melt flow index measurements and changes in the flow characteristics of moisture-exposed extrudate. DMA data show a distinct decrease in Tg with increased moisture content, which is consistent with plasticization. The absorption characteristics at room temperature lab conditions indicate that the material will reach an unacceptable level within one hour of room-temperature exposure. This investigation emphasized the need for awareness of the moisture sensitivities of ULTEM® 9085 when manufacturing high-quality material extrusion processed structures.

The moisture absorption of 3D printed short carbon fibre reinforced polyamide

The moisture absorption of additively manufactured short carbon fibre reinforced polyamide

Experimental and Theoretical Studies on 3D Printed Short and Continuous Carbon Fiber Hybrid Reinforced Composites

Evolution of microstructure and thermo‐mechanical attributes of fiber reinforced polyamide during fused deposition modeling 3D printing: A comprehensive characterization study

Influence of the Manufacturing Method (3D Printing and Injection Molding) on Water Absorption and Mechanical and Thermal Properties of Polymer Composites Based on Poly(lactic acid)

Moisture absorption of 3D-printed PETG plastic samples

Investigation on the mechanical properties of 3D printed hybrid continuous fiber-filled composite considering influence of interfaces

Effect of initial filament moisture content on the microstructure and mechanical performance of ULTEM® 9085 3D printed parts

Characterizing the Effect of Filament Moisture on Tensile Properties and Morphology of Fused Deposition Modeled Polylactic Acid/Polybutylene Succinate Parts

Hygrothermal aging and durability prediction of 3D-printed hybrid fiber composites with continuous carbon/Kevlar-fiber and short carbon-fiber

Effects of Coefficient of Thermal Expansion and Moisture Absorption on the Dimensional Accuracy of Carbon-Reinforced 3D Printed Parts

Static Behavior of a 3D-Printed Short Carbon Fiber Polyamide: Influence of the Meso-Structure and Water Content

An investigation into mechanical properties of a 3D printed two-matrix continuous fiber composites with multi-cavity structure

Evolution of Manufacturing Defects of 3D-Printed Thermoplastic Composites with Processing Parameters: A Micro-CT Analysis

Effects of printing direction on quasi‐static and dynamic compressive behavior of 3D printed short fiber reinforced polyamide‐based composites

Adjustment of Mechanical Properties of 3D Printed Continuous Carbon Fiber-Reinforced Thermoset Composites by Print Parameter Adjustments

Modelling of the temperature and residual stress fields during 3D printing of polymer composites

Effects of FDM-3D printing parameters on mechanical properties and microstructure of CF/PEEK and GF/PEEK

Water absorption rates and mechanical properties of material extrusion-printed continuous carbon fiber-reinforced nylon composites

The Influence of Moisture Absorption and Desorption by the ABS Filament on the Properties of Additively Manufactured Parts Using the Fused Deposition Modeling Method