Abstract:A robust perovskite–substrate interface is critical to realize state-of-the-art inverted (p–i–n) perovskite solar cells (PSCs), as it enables charge carrier selectivity by means of suitable electrostatics, energy level alignment, and low interfacial recombination. To achieve this goal of carrier selectivity in p–i–n type PSCs, we propose a strategy of carrier viaduct via an interfacial molecular bridge comprised of Ph-CH 2 N + H 3− n (CH 3 ) n ammonium cations (where n is the degree of substitution). Through a joint theoretical–experimental study, we demonstrate that the most stable heterointerface is established by quaternary ammonium (QA, n = 3), where the –N + (CH 3 ) 3 groups preferentially insert into the perovskite frameworks, with a vertical downward orientation of the phenyl groups towards the perovskite-substrates. This interfacial molecular bridge configuration as a carrier viaduct enables directional carrier management and redistributes a homogeneous environment at the heterointerface. Therefore, the carrier viaduct strategy enhances charge carrier extraction and transport in both in-plane or out-of-plane directions. Meanwhile, the bottom interfacial molecule acts as a double-sided molecular binder, maintaining the contact stack and strengthening the weak interface. The fabricated lab-scale inverted PSCs exhibit a champion efficiency of 25.45% (certified at 24.9%), with the fill factor exceeding 85.66%, corresponding to 95% of their thermodynamic limit at its bandgap ( E g = 1.54 eV). The corresponding perovskite solar modules for an active area of 23.25 cm 2 deliver an efficiency of 20.91%. Notably, even unencapsulated target PSCs retain nearly their initial efficiency after 3000 hours under light soaking at maximum power point tracking.

Charge-Carrier Balance for Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells

Charge Carrier Balance for Highly Efficient Inverted Planar Heterojunction Perovskite Solar Cells Based on Interface Engineering

High Performance Inverted RbCsFAPbI3 Perovskite Solar Cells Based on Interface Engineering and Defects Passivation.

Efficient and balanced charge transport revealed in planar perovskite solar cells.

High-performance Planar Heterojunction Perovskite Solar Cells: Preserving Long Charge Carrier Diffusion Lengths and Interfacial Engineering

Inverted Perovskite Solar Cells With Efficient Mixed-Fullerene Derivative Charge Extraction Layers

Bridged Carbolong Modulating Interfacial Charge Transfer Enhancement for High‐Performance Inverted Perovskite Solar Cells

Regulating Charge Carrier Extraction and Transport with Dual-interface Modification for Efficient Perovskite Solar Cells

Efficient and stable inverted perovskite solar cells enabled by homogenized PCBM with enhanced electron transport

Balancing Charge Extraction for Efficient Back‐Contact Perovskite Solar Cells by Using an Embedded Mesoscopic Architecture

Constructing robust heterointerfaces for carrier viaduct via interfacial molecular bridges enables efficient and stable inverted perovskite solar cells

Interfacial Passivation of the p-Doped Hole-Transporting Layer Using General Insulating Polymers for High-Performance Inverted Perovskite Solar Cells

A p‐p + Homojunction‐Enhanced Hole Transfer in Inverted Planar Perovskite Solar Cells

Preheating-assisted deposition of solution-processed perovskite layer for an efficiency-improved inverted planar composite heterojunction solar cell

Simultaneously Enhanced J(Sc) And Ff By Employing Two Solution-Processed Interfacial Layers For Inverted Planar Perovskite Solar Cells

Bimolecular Passivation‐Dipole Bridge for Highly Efficient Inverted Perovskite Solar Cells with Low Nonradiative Recombination Loss

Efficient Charge Transport in Inverted Perovskite Solar Cells via 2D/3D Ferroelectric Heterojunction

Photoconductive Charge Transfer Complexes as Charge Transport Layers for High Performance Inverted Perovskite Solar Cells

High-performance inverted planar heterojunction perovskite solar cells based on a solution-processed CuOx hole transport layer.

Interface engineering for high-efficiency perovskite solar cells

Bifacial Modified Charge Transport Materials for Highly Efficient and Stable Inverted Perovskite Solar Cells