Injectable thermogels and their biomedical applications
Yu Lin,Shen Wenjia,Luan Jiabin,Lei Kewen,Chen Yipei,Ding Jiandong
DOI: https://doi.org/10.3389/conf.FBIOE.2016.01.01210
IF: 5.7
2016-01-01
Frontiers in Bioengineering and Biotechnology
Abstract:Event Abstract Back to Event Injectable thermogels and their biomedical applications Lin Yu1*, Wenjia Shen1*, Jiabin Luan1, Kewen Lei1*, Yipei Chen1* and Jiandong Ding1* 1 Fudan University, State Key Laboratory of Molecular Engineering of Polymers & Department of Macromolecular Science, China Thermogelling polymers based on poly(ethylene glycol) (PEG) and biodegradable polyesters have been suggested as very promising biomaterials[1]-[5]. However, the composition window of PEG/polyester polymers to form a thermogel is quite narrow.1 In this study, a facile method to obtain a thermogel was found by simply mixing an aqueous sol of a block copolymer with a precipitate of a similar copolymer but with a different block ratio (Fig. 1a). Two triblock copolymers poly(D,L-lactic acid-co-glycolic acid)-b-poly(ethylene glycol)-b-poly(D,L-lactic acid-co-glycolic acid) (PLGA-PEG- PLGA) were synthesized. One sample in water was a sol in a broad temperature region, while the other in water was just a precipitate. The mixture of these two samples with a certain mix ratio underwent, however, a sol-gel transition upon heating. Thus, the applicable window of pertinent polymers has been broadened to a large extent. Next, the biodegradation and biocompatibility of these mixture hydrogels were confirmed. Finally, the mixture thermogel was applied as an injectable depot for sustained delivery of exenatide (EXT), a glucose-dependent insulinotropic hormone (Fig. 1b). The synergistic effect of sucrose, PEG200 and zinc acetate as additives was found to not only significantly decrease the burst release but also maintain the almost complete release at the late stage for the EXT thermogel formulation (Fig. 1c). After a subcutaneous injection of the EXT formulation into db/db mice, the blood glucose level was maintained in a normal range up to 7 days. The in vivo results were well consistent with the in vitro EXT-release profile. Hence, the injectable, biodegradable and thermosensitive mixture hydrogel has a great promise as a delivery system of EXT with improved patient compliance. The strategy to use the synergistic excipients to reduce the early-stage burst effect and enhance the late-stage release might also be stimulating for other hydrogel formulations of hydrophilic and charged drugs. National Natural Science Fund of China (Grants No. 51273217, No. 21474019)References:[1] Yu L, Ding JD. Chem. Soc. Rev. 2008, 37: 1473-1481.[2] Zhang L, Shen WJ, Luan JB, Yang DX, Wei G*, Yu L*, Lu WY, Ding JD. Acta Biomater. 2015, 23: 271-281.[3] Shen WJ, Luan JB, Cao LP, Sun J, Yu L*, Ding JD. Biomacromolecules 2015, 16, 105-115.[4] Cao LP, Cao B, Lu CJ, Wang GW, Yu L*, Ding JD. J Mater. Chem. B. 2015, 3, 1268-1280.[5] Lei KW, Shen WJ, Cao LP, Yu L*, Ding JD. Chem. Commun. 2015.51, 6080-6083. Keywords: Hydrogel, Drug delivery, Environmental response, Bioactive molecule Conference: 10th World Biomaterials Congress, Montréal, Canada, 17 May - 22 May, 2016. Presentation Type: Poster Topic: Biomaterials for therapeutic delivery Citation: Yu L, Shen W, Luan J, Lei K, Chen Y and Ding J (2016). Injectable thermogels and their biomedical applications. Front. Bioeng. Biotechnol. Conference Abstract: 10th World Biomaterials Congress. doi: 10.3389/conf.FBIOE.2016.01.01210 Copyright: The abstracts in this collection have not been subject to any Frontiers peer review or checks, and are not endorsed by Frontiers. They are made available through the Frontiers publishing platform as a service to conference organizers and presenters. The copyright in the individual abstracts is owned by the author of each abstract or his/her employer unless otherwise stated. Each abstract, as well as the collection of abstracts, are published under a Creative Commons CC-BY 4.0 (attribution) licence (https://creativecommons.org/licenses/by/4.0/) and may thus be reproduced, translated, adapted and be the subject of derivative works provided the authors and Frontiers are attributed. For Frontiers’ terms and conditions please see https://www.frontiersin.org/legal/terms-and-conditions. Received: 27 Mar 2016; Published Online: 30 Mar 2016. * Correspondence: Dr. Lin Yu, Fudan University, State Key Laboratory of Molecular Engineering of Polymers & Department of Macromolecular Science, Shanghai, China, Email1 Dr. Wenjia Shen, Fudan University, State Key Laboratory of Molecular Engineering of Polymers & Department of Macromolecular Science, Shanghai, China, 13210440019@fudan.edu.cn Dr. Kewen Lei, Fudan University, State Key Laboratory of Molecular Engineering of Polymers & Department of Macromolecular Science, Shanghai, China, 10301020028@fudan.edu.cn Dr. Yipei Chen, Fudan University, State Key Laboratory of Molecular Engineering of Polymers & Department of Macromolecular Science, Shanghai, China, 10300220061@fudan.edu.cn Dr. Jiandong Ding, Fudan University, State Key Laboratory of Molecular Engineering of Polymers & Department of Macromolecular Science, Shanghai, China, jdding1@fudan.edu.cn Login Required This action requires you to be registered with Frontiers and logged in. To register or login click here. Abstract Info Abstract The Authors in Frontiers Lin Yu Wenjia Shen Jiabin Luan Kewen Lei Yipei Chen Jiandong Ding Google Lin Yu Wenjia Shen Jiabin Luan Kewen Lei Yipei Chen Jiandong Ding Google Scholar Lin Yu Wenjia Shen Jiabin Luan Kewen Lei Yipei Chen Jiandong Ding PubMed Lin Yu Wenjia Shen Jiabin Luan Kewen Lei Yipei Chen Jiandong Ding Related Article in Frontiers Google Scholar PubMed Abstract Close Back to top Javascript is disabled. Please enable Javascript in your browser settings in order to see all the content on this page.