Constitutive parameter identification of 3D printing material based on the virtual fields method

xianglu dai

DOI: https://doi.org/10.1016/j.measurement.2014.09.033

IF: 5.6

2015-01-01

Measurement

Abstract:•Constitutive parameter identification method for 3D printing material is presented.•Design method of 3D printing specimen with deformation carriers is offered.•Influence of missing data near the specimen edge on VFM is analyzed.

What problem does this paper attempt to address?

Characterization of Mechanical Properties of 3-D–printed Materials Using the Asymmetric Four-Point Bending Test and Virtual Fields Method

M. M. Zhou,W. He,H. M. Xie,S. Liu

DOI: https://doi.org/10.1520/jte20180598

2019-01-01

Journal of Testing and Evaluation

Abstract:The virtual fields method (VFM) is an inverse method for characterizing the mechanical properties of materials that has the advantage that all constitutive parameters can be identified using one test. The accuracy of identification is mainly determined by the load configuration, deformation measurement, and virtual displacement fields. In order to promote the use of VFM, a new load configuration for the asymmetric four-point bending (4PB) test is proposed here. A virtual experiment was performed to examine the feasibility of the asymmetric 4PB test, where the configuration of the proposed test was optimized to achieve high identification accuracy. As an example of a practical application, the proposed method combined with moire interferometry was used to characterize the constitutive parameters of stainless-steel materials fabricated by selective laser-melting 3-D printing. It was demonstrated that this method is suitable for characterizing the material properties of 3-D-printed materials.
Self-monitoring Continuous Carbon Fiber Reinforced Thermoplastic Based on Dual-Material Three-Dimensional Printing Integration Process

Congcong Luan,Xinhua Yao,Chengzhe Liu,Liujian Lan,Jianzhong Fu

DOI: https://doi.org/10.1016/j.carbon.2018.08.019

IF: 10.9

2018-01-01

Carbon

Abstract:This study offers a novel dual-material three-dimensional (3D) printing technology for integrating of continuous carbon fibers within 3D printed thermoplastic structures to achieve both structural reinforcement and self-monitoring. Mechanical and electrical-resistance-based self-sensing properties of different fill density specimens under tensile and flexural loading were investigated and discussed. Results showed that continuous carbon fibers integrated in the thermoplastic contributed to both structural reinforcement and structural health via in situ monitoring. With up to 7.23% improvement of tensile strength, 19.07% improvement of tensile modulus, 38.66% improvement of flexural strength, and 17.99% improvement of flexural modulus for specimens compared to the non-integrated continuous carbon fibers specimens. Changes in electrical resistance measurements of the carbon fibers allowed the detection of both strain and damage in 3D printed thermoplastic structures in a very effective and sensitive way. Gauge factors of different fill density specimens ranged from 0.119 +/- 0.016 up to 1.213 +/- 0.165 for the uniaxial tension test in the un-cracked region. Taken together, these results suggest that this dual-material 3D printing technology is attractive for fabrication of continuous carbon fiber thermoplastic matrix (CCFT) smart structures, and have many potential civil and military applications. (C) 2018 Elsevier Ltd. All rights reserved.
Numerical Simulation and Printability Analysis of Fused Deposition Modeling with Dual-Temperature Control

Xiaodan Huo,Bin Zhang,Qianglong Han,Yong Huang,Jun Yin

DOI: https://doi.org/10.1007/s42242-023-00239-1

2023-01-01

Bio-Design and Manufacturing

Abstract:Ideal tissue engineering scaffolds need interconnected pores and high porosity to enable cell survival, migration, proliferation, and differentiation. However, obtaining a high-resolution structure is difficult with traditional one-temperature control fused deposition modeling (FDM). In this study, we propose a dual-temperature control method to improve printability. A numerical model is developed in which the viscosity is a function of temperature and shear rate to study the influence of two different temperature control modes. Quantitative tests are used to assess filament formation and shape fidelity, including one-dimensional filament printing, deposition at corners, fusion, and collapse. By using dual-temperature control, the width of the deposited poly(ε-caprolactone) filament is reduced to 50 μm. The comparative results of both the experimental method and numerical simulation suggest that the dual-temperature control FDM can manufacture spatially arranged constructs and presents a promising application in tissue engineering.
Characterization of Material Mechanical Properties Using Strain Correlation Method Combined with Virtual Fields Method

Li Yangyang,Li Jiaqiang,Duan Qiyuan,Xie Huimin,Liu Sheng

DOI: https://doi.org/10.1007/s10409-020-01014-6

IF: 3.5

2021-01-01

Acta Mechanica Sinica

Abstract:The isotropic and anisotropic behaviors are considered as the important formats of the constitutive behaviors, and can also be called the global properties. To improve the identification ability of virtual fields method (VFM) when the global properties are unknown, this paper proposes the strain correlation method (SCM) to determine the global properties before the parameter identification using the VFM. Firstly, the basic principle of SCM is described in detail. Then, the feasibility and accuracy of SCM are verified through the numerical experiments based on the three-point bending configuration and the real experiment of polymethyl methacrylate (PMMA). The influence of the additive Gaussian white noise, local errors in the strain fields, and missing data at the specimen edges on the characterization results are evaluated. The results show that the SCM has good noise immunity and lower accuracy requirements for the strain fields. As an application, the mechanical properties of Ti-6Al-4V alloys fabricated by selective laser melting (SLM) are characterized by the SCM. The results show that the alloys are isotropic, and the isotropic VFM is utilized to determine the mechanical parameters. By using the SCM, the accuracy of identification results can be improved for the isotropic or bidirectional reinforced orthotropic materials when using VFM. Graphic abstract
Finite Element Analysis of Warping and Mechanical Properties of 3D Parts Printed by Fused Deposition Modeling

Baiqing Yu,Guoguang Chen,Jingfeng Sun,Weijian Hua,Weibin Wu,Yifei Jin,Wuyi Zhou,Jia Liu,Wenxu Zheng

DOI: https://doi.org/10.1007/s11665-024-09243-7

IF: 2.3

2024-03-15

Journal of Materials Engineering and Performance

Abstract:Fused deposition modeling (FDM) is one of the most commonly used 3D printing techniques. The printing parameter, called infill line directions (ILDs), not only affects the distortion, but also determines the mechanical properties of the printed specimens. To explore and predict the effects of ILDs on warping and mechanical properties, numerical simulation was used in this work to perform finite element analysis of FDM processes and mechanical properties of printed specimens. Through theoretical investigation and comprehensive analysis, the interrelationships between the printing parameter ILDs, warpage, and mechanical properties of the specimens were established and the optimal printing parameters can be obtained. Based on the simulation results, the following conclusions are drawn: In warping analysis, the bending and tensile specimens with ILD [−90, 90] have the highest tendency to warp the arch bridge. In the mechanical analysis, the tensile specimens with ILD [−90, 90] have the best mechanical properties followed by the specimens with ILD [−45, 45], while for the bending specimens, the best and the next best ILDs are [−90, 90] and [−60, 60], respectively. The simulation results matched well with the experimental results.

materials science, multidisciplinary
Complicated Deformation Simulating on Temperature-Driven 4D Printed Bilayer Structures Based on Reduced Bilayer Plate Model

Song Junjie,Feng Yixiong,Wang Yong,Zeng Siyuan,Hong Zhaoxi,Qiu Hao,Tan Jianrong

DOI: https://doi.org/10.1007/s10483-021-2788-9

2021-01-01

Applied Mathematics and Mechanics

Abstract:The four-dimensional (4D) printing technology, as a combination of additive manufacturing and smart materials, has attracted increasing research interest in recent years. The bilayer structures printed with smart materials using this technology can realize complicated deformation under some special stimuli due to the material properties. The deformation prediction of bilayer structures can make the design process more rapid and thus is of great importance. However, the previous works on deformation prediction of bilayer structures rarely study the complicated deformations or the influence of the printing process on deformation. Thus, this paper proposes a new method to predict the complicated deformations of temperature-sensitive 4D printed bilayer structures, in particular to the bilayer structures based on temperature-driven shape-memory polymers (SMPs) and fabricated using the fused deposition modeling (FDM) technology. The programming process to the material during printing is revealed and considered in the simulation model. Simulation results are compared with experiments to verify the validity of the method. The advantages of this method are stable convergence and high efficiency, as the three-dimensional (3D) problem is converted to a two-dimensional (2D) problem. The simulation parameters in the model can be further associated with the printing parameters, which shows good application prospect in 4D printed bilayer structure design.
Elasto-Plastic Mechanical Modeling of Fused Deposition 3D Printing Materials

Francesco Bandinelli,Lorenzo Peroni,Alberto Morena

DOI: https://doi.org/10.3390/polym15010234

IF: 5

2023-01-03

Polymers

Abstract:Fused deposition modeling (FDM) is one of the most common 3D printing technologies and is becoming a well-established production method. Short fiber-reinforced polymers represent a new class of printing materials that enhance the mechanical properties of final components, thus informing an interesting subject of analysis for this study. FDM-printed parts are characterized by a strong anisotropy, so their behavior should be analyzed accordingly. The authors proposed a modeling strategy based on a transversely isotropic behavior hypothesis, representing material behaviors associated with an elasticity matrix in relation to the elastic field and a combination of Hill's yield criterion and Voce's isotropic hardening law for the plastic field. Material properties of materials were experimentally identified through tensile tests on dog bone specimens printed with different orientations in space. The numerical model was then calibrated using the finite element software LS-DYNA and the optimization software LS-OPT. An agreement between numerical and experimental results showed the robustness of the modeling strategy proposed to describe the stress behaviors of printed materials until a maximum load is reached, while strain behaviors have yet to be correctly defined due to the difficulties associated with evaluating an equivalent deformation.

polymer science
Virtual fields method coupled with moiré interferometry: Special considerations and application

Mengmeng Zhou,Huimin Xie,Lifu Wu

DOI: https://doi.org/10.1016/j.optlaseng.2016.04.013

IF: 5.666

2016-01-01

Optics and Lasers in Engineering

Abstract:The virtual fields method (VFM) is a novel highly efficient non-iterative tool for the identification of the constitutive parameters of materials. The VFM can obtain several constitutive parameters based on the full-field deformation of the specimen measured in a single test. However, the available results demonstrate that the accuracy of the identification result is strongly dependent on the quality of the deformation field, which is generally measured using optical methods. Especially, in the case where a small deformation is applied under elastic loading, the image noise and measurement error will exhibit a significant influence on the identification results. By combining the VFM with moiré interferometry (MI), a MI-based VFM is used to identify the parameters of an orthotropic linear elastic material. A numerical experiment is conducted to examine the feasibility of this method. From the analysis results, we determine that two factors exhibit an influence on the identification accuracy. The reinforcement direction of the orthotropic material is one factor, and the other is the noise in the deformation field. This MI-based VFM is then applied to determine the mechanical parameters of a unidirectional carbon fiber composite material. In the measurement, a three-point bending load is applied to the specimens. A high density grating with a frequency of 1200line/mm grating is replicated on the specimen surface and used for measuring the in-plane deformation fields using a moiré interferometer. The obtained deformation fields are taken as the inputs of the VFM identification process, and the elastic properties of the materials are identified. The obtained results verify the advantage of the proposed method with respect to high accuracy and good noise immunity.
Characterization for elastic constants of fused deposition modelling-fabricated materials based on the virtual fields method and digital image correlation

Quankun Cao,Huimin Xie

DOI: https://doi.org/10.1007/s10409-017-0719-y

IF: 3.5

2017-01-01

Acta Mechanica Sinica

Abstract:Fused deposition modelling (FDM), a widely used rapid prototyping process, is a promising technique in manufacturing engineering. In this work, a method for characterizing elastic constants of FDM-fabricated materials is proposed. First of all, according to the manufacturing process of FDM, orthotropic constitutive model is used to describe the mechanical behavior. Then the virtual fields method (VFM) is applied to characterize all the mechanical parameters (Q_11 , Q_22 , Q_12 , Q_66) using the full-field strain, which is measured by digital image correlation (DIC). Since the principal axis of the FDM-fabricated structure is sometimes unknown due to the complexity of the manufacturing process, a disk in diametrical compression is used as the load configuration so that the loading angle can be changed conveniently. To verify the feasibility of the proposed method, finite element method (FEM) simulation is conducted to obtain the strain field of the disk. The simulation results show that higher accuracy can be achieved when the loading angle is close to 30^∘ . Finally, a disk fabricated by FDM was used for the experiment. By rotating the disk, several tests with different loading angles were conducted. To determine the position of the principal axis in each test, two groups of parameters (Q_11 , Q_22 , Q_12 , Q_66) are calculated by two different groups of virtual fields. Then the corresponding loading angle can be determined by minimizing the deviation between two groups of the parameters. After that, the four constants (Q_11 , Q_22 , Q_12 , Q_66) were determined from the test with an angle of 27^∘ .
Process-dependent Multiscale Modeling for 3D Printing of Continuous Fiber-reinforced Composites

Junming Zhang,Weidong Yang,Yan Li

DOI: https://doi.org/10.1016/j.addma.2023.103680

IF: 11

2023-07-08

Additive Manufacturing

Abstract:Three-dimensional (3D) printing has broad application prospects in the field of lightweight composite structures due to its superior manufacturing flexibility. However, current 3D-printed continuous fiber-reinforced thermoplastic (CFRTP) parts and components suffer from poor mechanical properties due to processing defects that arise from poor resin impregnation in fiber bundles. Impregnation only occurs when the resin is molten. Hence, the evolution of the thermal field in the local space being printed is critical to determine the degree of resin impregnation. In this paper, we presented a new method to regulate the transient 3D thermal field during printing via an external laser heat source, thus effectively improving the resin impregnation of 3D-printed CFRTPs. To reveal their quantitative relations, the 3D thermal field and consequent impregnation behavior of resin in fiber bundles were numerically modeled. Furthermore, a process-dependent multiscale mechanical model was developed to investigate the tensile strength of 3D-printed composites based on the impregnation analysis framework. The parameters in the proposed models were determined experimentally. The thermal model was demonstrated and validated experimentally through thermocouple measurements. The impregnation percentage and tensile strength of the printed samples were determined using microscopy and tensile testing, respectively. Simulation results agreed well with experimental data, indicating the good accuracy of the proposed modeling methods. The findings provide insights into the process-impregnation-property relationship in 3D printing of CFRTP structures. Based on these findings, an effective method has been proposed to reduce printing defects and improve manufacturing efficiency by improving the thermal field.

engineering, manufacturing,materials science, multidisciplinary
Research on Behaviors of Functional Components Based on 4D Printing and Design of Temperature-driven Deformation

GAO Yicong,ZENG Siyuan,XU Junjun,ZHENG Hao,TAN Jianrong

DOI: https://doi.org/10.3901/jme.2023.03.189

2023-01-01

Journal of Mechanical Engineering

Abstract:：4D printing is an intelligent additive manufacturing technology based on 3D printing.It is applied to fabricate functional components that perform controllable transformations of geometric structure, function and performance under external excitation such as temperature, magnetic field and ultraviolet ray.A bilayer functional component was employed and the thermal expansions of two layers are analysed.The thermal deformation mechanism of 4D printed functional components is investigated and the deformation patterns of functional components based on arrangement of shape memory polymer fibre are obtained.Then, effect of 3D printing process parameters on functional components is analysed, and an approximate analytical model of temperature-driven deformation of functional components is established.The equivalent temperature-driven deformation models of bending and helixing behaviors are fitted by partial least squares method.These models are verified by the comparison between the measured values and calculated values.Finally, a self-folding functional component and a self-assembling functional component are designed and fabricated by 4D printing.The programmability of functional components is verified and it is helpful to design the behaviors of functional components based on 4D printing.
Multiscale Computational Modeling of 3D Printed Continuous Fiber-Reinforced Composites

Xin Li

DOI: https://doi.org/10.1166/jbn.2024.3913

2024-04-20

Journal of Biomedical Nanotechnology

Abstract:The printing parameters used during the printing procedure have a significant effect on the mechanical characteristics of 3D printed continuous fiber reinforced composites (3DP-CFRPCs). However, conducting experimental assessments of the material characteristics of 3DP-CFRPCs may require more effort and incur more costs. Computational material modeling may be used as a viable alternative to investigate the behavior of 3DP-CFRPCs under various printing conditions. The current work used material modeling approaches to examine the impact of different printing settings on the elastic characteristics of 3DP-CFRPCs. The inherent flexibility of beads is primarily established by homogenizing the pores within the matrix via the use of the Mori-Tanaka process. Subsequently, the elastic modulus is calculated by using finite element modeling on Representative Volume Element (RVE), which takes into account the microstructure and other printing attributes. An inconsistency was seen in the variation of projected elastic properties across models distinguished by various microstructures, with a more pronounced differentiation observed between intricate and simpler microstructures. Computational modeling has enhanced our understanding of the elastic properties of 3DP-CFRPCs under various printing conditions. Moreover, it has been shown that alterations in printing parameters have diverse impacts on the pliable characteristics of 3DP-CFRPCs. The impact of layer thickness on the mechanical characteristics of 3DP-CFRPCs was determined to be more substantial compared to the effect of printing temperature. The application of offset layup printing techniques enhanced the elastic properties of 3DP-CFRPCs, with the degree of improvement varying based on the orientation. As the level of porosity increased, the influence of pores situated between beads on the overall stiffness of 3DP-CFRPCs gradually diminished, while the impact of matrix pores on the overall stiffness of 3DP-CFRPCs gradually intensified.

materials science, biomaterials,nanoscience & nanotechnology
Study of thermal stress deformation in hybrid 3D printing and milling process of PEEK material

Haoyi Sun,Xiang Cheng,Ruichun Dong,Huanbao Liu,Guangming Zheng,Lei He,Wenbo Wang,Kun Tan

DOI: https://doi.org/10.1177/14644207241292818

2024-10-24

Proceedings of the Institution of Mechanical Engineers Part L Journal of Materials Design and Applications

Abstract:Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, Ahead of Print. Hybrid manufacturing can enable rapid production of personalized artificial bones that are made of Polyether-ether-ketone (PEEK) by integrating 3D printing and milling. A main challenge, however, is the thermal stress deformation that arises from the fused deposition process, leading to warping and shrinkage. As a result, the fabrication accuracy is significantly diminished. This work aims to address this challenge by investigating the thermal stress deformation behavior of PEEK in hybrid manufacturing. The main contributions of this work, therefore, include the development of a model for this thermal deformation behavior, and the identification of key parameters such as cross-section length (Ls), printed layer thickness (Lh), and current workpiece height (He). Further, experiments are conducted based on response surface methodology (RSM) to explore the relationships between temperature variation rate (ΔT), end surface height difference (ΔS), and length shrinkage rate (ΔL) with critical hybrid processing parameters. Optimal parameter combinations are then identified. Our experiments demonstrate that the proposed methods effectively reduce the effects of warping and shrinkage.

materials science, multidisciplinary
Constitutive Parameters Identification of Thermal Barrier Coatings Using the Virtual Fields Method

Mengmeng Zhou,Huimin Xie,Luming Li

DOI: https://doi.org/10.1007/s10409-018-0787-7

IF: 3.5

2019-01-01

Acta Mechanica Sinica

Abstract:Thermal barrier coatings (TBCs) are widely applied in thermal components to protect metallic components. Owing to the complex layered structure of TBCs and difficult preparation of coating, the mechanical characterization of TBCs should be of primary importance. With regard to TBCs, this study deals with the constitutive parameters identification of bi-material. Considering the complex construction and boundary of bi material, the virtual fields method (VFM) was employed in this study. A methodology based on the optimized virtual fields method combined with moiré interferometry was proposed for the constitutive parameters identification of bi-material. The feasibility of this method is verified using simulated deformation fields of a two-layer material subjected to three point bending loading. As an application, the deformation fields of the TBC specimens were measured by moiré interferometry. Then, the mechanical parameters of the coating were identified by the proposed method. The identification results indicate that Young’s modulus of the TBC top coating is 89.91 GPa, and its Poisson’s ratio is 0.23.
Multi-parametric numerical analysis of 3D printed sparse infill structures

Petros Gkertzos,Athanasios Kotzakolios,Vassilis Kostopoulos

DOI: https://doi.org/10.1007/s00170-024-14173-8

IF: 3.563

2024-08-27

The International Journal of Advanced Manufacturing Technology

Abstract:Due to the increase in 3D printing popularity, optimizing the procedure has become an important aspect of fused deposition modeling (FDM) research. As such, a numerical framework that captures the effect of all parameters involved in the process can aid in manufacturing optimization by overcoming the cost and time limitations of experimental methods. In this work, a numerical physics-based model is created that takes as input process parameters, simulates the phenomenon, and identifies the temperature history and developed mechanical stresses during printing. Initially, this model is validated through images taken from an infrared camera. Then, a design of experiments (DOE) sequence that covers the range of each input variable is created and multiple designs are evaluated. Correlations are examined and factor analysis on each output is performed indicating that material and bed temperature are the most important parameters affecting mechanical stresses, while fan speed dominates cooling. The simulation data are fed into data-driven models to provide accurate estimations on cooling duration, plastic strain, and von Misses stress and in turn aid in optimal parameter selection. This work improves existing numerical approaches by incorporating multiple process parameters and aids in digital twinning of FDM.

engineering, manufacturing,automation & control systems
Material characterization and precise finite element analysis of fiber reinforced thermoplastic composites for 4D printing

Yuxuan Yu,Haolin Liu,Kuanren Qian,Humphrey Yang,Matthew McGehee,Jianzhe Gu,Danli Luo,Lining Yao,Yongjie Jessica Zhang

DOI: https://doi.org/10.1016/j.cad.2020.102817

2020-05-01

Abstract:A novel workflow is proposed for forward design, with accurate material property characterization and precise FEA simulation. This workflow supports robust and accurate fabrication of the designed object through an iterative optimization process and accurate control of the final configuration.The material properties of 3D printing polymers, including both PLA and CFPLA, are characterized in a precise way based on the DMA experiments. The characterization results are effectively incorporated into FEA with accurate mathematical models.A sequential FEA is developed to achieve accurate simulation results, considering both the residual stress releasing and the body force creeping. We simulate these two processes in a sequence to precisely derive the final deformation of the fabricated product.Four-dimensional (4D) printing, a new technology emerged from additive manufacturing (3D printing), is widely known for its capability of programming post-fabrication shape-changing into artifacts. Fused deposition modeling (FDM)-based 4D printing, in particular, uses thermoplastics to produce artifacts and requires computational analysis to assist the design processes of complex geometries. However, these artifacts are weak against structural loads, and the design quality can be limited by less accurate material models and numerical simulations. To address these issues, this paper propounds a composite structure design made of two materials - polylactic acid (PLA) and carbon fiber reinforced PLA (CFPLA) - to increase the structural strength of 4D printed artifacts and a workflow composed of several physical experiments and series of dynamic mechanical analysis (DMA) to characterize materials. We apply this workflow to 3D printed samples fabricated with different printed parameters to accurately characterize the materials and implement a sequential finite element analysis (FEA) to achieve accurate simulations. The accuracy of deformation induced by the triggering process is both computationally and experimentally verified with several creative design examples and is measured to be at least 95%, with a confidence interval of <math>(0.972,0.985)</math>. We believe the presented workflow is essential to the combination of geometry, material mechanism and design, and has various potential applications.<ol class="links-for-figure"><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S0010448520300105-fx1_lrg.jpg">Download : Download high-res image (193KB)</a></li><li><a class="anchor download-link u-font-sans" href="https://ars.els-cdn.com/content/image/1-s2.0-S0010448520300105-fx1.jpg">Download : Download full-size image</a></li></ol>

computer science, software engineering
Physics-informed machine learning enabled virtual experimentation for 3D printed thermoplastic

Zhenru Chen,Yuchao Wu,Yunchao Xie,Kianoosh Sattari,Jian Lin

DOI: https://doi.org/10.1039/d4mh01022a

IF: 13.3

2024-10-03

Materials Horizons

Abstract:The performance of 3D printed thermoplastics largely depends on the ink formulation, which is composed of tremendous chemical space as an increased number of monomers, making it very difficult to identify an optimum one with desired properties. To tackle this challenge, we demonstrate a virtual experimentation platform that is enabled by a physics-informed machine learning algorithm. As a case study, the algorithm was trained based on a multilayer perceptron (MLP) model to predict the experimental stress–strain curves of the 3D printed thermoplastics given the ink compositions made of six monomers. To solve the issue of experimental data scarcity, we first reduced the dimensions of the curves to eight principal components (PCs), which serve as the outputs of the model. In addition, we incorporated the physics-informed descriptors into the input dataset. These two strategies afford the model with a prediction accuracy of R 2 of 0.97 and an RMSE value of 1.01 for fracture strength, and an R 2 of 0.95 and a RMSE of 0.40 for toughness. To perform virtual experimentation, the well-trained model was then utilized to predict 100 000 sets of the PCs from the randomly given 100 000 ink formulations. The PC sets were then converted back to the corresponding stress–strain curves. To validate the prediction results, some of the virtual experiments were performed. The results showed a good match between the predicted and experimental curves. This methodology offers a general and efficient pathway to virtual experimentation for establishing the correlation between the complex input variables and the output performance metrics of new materials.

materials science, multidisciplinary,chemistry
An Artificial-intelligence/Statistics Solution to Quantify Material Distortion for Thermal Compensation in Additive Manufacturing

Chao Wang,Shaofan Li,Danielle Zeng,Xinhai Zhu

DOI: https://doi.org/10.48550/arXiv.2005.09084

2020-05-14

Computational Engineering, Finance, and Science

Abstract:In this paper, we introduce a probabilistic statistics solution or artificial intelligence (AI) approach to identify and quantify permanent (non-zero strain) continuum/material deformation only based on the scanned material data in the spatial configuration and the shape of the initial design configuration or the material configuration. The challenge of this problem is that we only know the scanned material data in the spatial configuration and the shape of the design configuration of three-dimensional (3D) printed products, whereas for a specific scanned material point we do not know its corresponding material coordinates in the initial or designed referential configuration, provided that we do not know the detailed information on actual physical deformation process. Different from physics-based modeling, the method developed here is a data-driven artificial intelligence method, which solves the problem with incomplete deformation data or with missing information of actual physical deformation process. We coined the method is an AI-based material deformation finding algorithm. This method has practical significance and important applications in finding and designing thermal compensation configuration of a 3D printed product in additive manufacturing, which is at the heart of the cutting edge 3D printing technology. In this paper, we demonstrate that the proposed AI continuum/material deformation finding approach can accurately find permanent thermal deformation configuration for a complex 3D printed structure component, and hence to identify the thermal compensation design configuration in order to minimizing the impact of temperature fluctuations on 3D printed structure components that are sensitive to changes of temperature.
A Sensitivity Analysis-Based Parameter Optimization Framework for 3D Printing of Continuous Carbon Fiber/Epoxy Composites

Hong Xiao,Wei Han,Yueke Ming,Zhongqiu Ding,Yugang Duan

DOI: https://doi.org/10.3390/ma12233961

IF: 3.4

2019-11-29

Materials

Abstract:Three-dimensional printing of continuous carbon fiber/epoxy composites (CCF/EPCs) is an emerging additive manufacturing technology for fiber-reinforced polymer composites and has wide application prospects. However, the 3D printing parameters and their relationship with the mechanical properties of the final printed samples have not been fully investigated in a computational and quantifiable way. This paper presents a sensitivity analysis (SA)-based parameter optimization framework for the 3D printing of CCF/EPCs. A surrogate model for a process parameter–mechanical property relationship was established by support vector regression (SVR) analysis of the experimental data on flexural strength and flexural modulus under different process parameters. An SA was then performed on the SVR surrogate model to calculate the importance of each individual 3D printing parameter on the mechanical properties of the printed samples. Based on the SA results, the optimal 3D printing parameters and the corresponding flexural strength and flexural modulus of the printed samples were predicted and verified by experiments. The results showed that the proposed framework can serve as a high-accuracy tool to optimize the 3D printing parameters for the additive manufacturing of CCF/EPCs.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
Multimaterial direct 4D printing of high stiffness structures with large bending curvature

Chao Yuan,Fangfang Wang,Qi Ge

DOI: https://doi.org/10.1016/j.eml.2020.101122

IF: 4.728

2021-01-01

Extreme Mechanics Letters

Abstract:The emerging direct four dimensional (4D) printing approach is considered as an easy, fast and economical manufacturing strategy that fabricates complex 3D geometries evolving from printed flat patterns in response to external stimuli. However, its implementation to practical engineering applications is impeded by the fact that the existing direct 4D printing methods could not render both the large bending curvature and high loading capacity at the same time. Herein, we report a multimaterial direct 4D printing method to fabricate patterned laminate that consists of covalently bonded elastomer and high-water-content hydrogel. The dehydration induced large volumetric shrinkage (up to 60%) and great modulus escalation (from 100 kPa to 4 GPa) allow the printed flat patterns to evolve into complex 3D structures with large bending curvature (up to 0.7 mm−1) and high bending stiffness (up to 104 MPa m3). To facilitate the structural design, we develop a phenomenological model to describe the dehydration induced shrinkage and stiffening, and implement this model to Euler–Bernoulli beam theory and finite element approach. Compared with other 3D printing technologies, the proposed multimaterial direct 4D printing approach demonstrates the merits in terms of less building time and high load capacity at both room temperature and high temperature.

mechanics,materials science, multidisciplinary

Constitutive parameter identification of 3D printing material based on the virtual fields method

Characterization of Mechanical Properties of 3-D–printed Materials Using the Asymmetric Four-Point Bending Test and Virtual Fields Method

Self-monitoring Continuous Carbon Fiber Reinforced Thermoplastic Based on Dual-Material Three-Dimensional Printing Integration Process

Numerical Simulation and Printability Analysis of Fused Deposition Modeling with Dual-Temperature Control

Characterization of Material Mechanical Properties Using Strain Correlation Method Combined with Virtual Fields Method

Finite Element Analysis of Warping and Mechanical Properties of 3D Parts Printed by Fused Deposition Modeling

Complicated Deformation Simulating on Temperature-Driven 4D Printed Bilayer Structures Based on Reduced Bilayer Plate Model

Elasto-Plastic Mechanical Modeling of Fused Deposition 3D Printing Materials

Virtual fields method coupled with moiré interferometry: Special considerations and application

Characterization for elastic constants of fused deposition modelling-fabricated materials based on the virtual fields method and digital image correlation

Process-dependent Multiscale Modeling for 3D Printing of Continuous Fiber-reinforced Composites

Research on Behaviors of Functional Components Based on 4D Printing and Design of Temperature-driven Deformation

Multiscale Computational Modeling of 3D Printed Continuous Fiber-Reinforced Composites

Study of thermal stress deformation in hybrid 3D printing and milling process of PEEK material

Constitutive Parameters Identification of Thermal Barrier Coatings Using the Virtual Fields Method

Multi-parametric numerical analysis of 3D printed sparse infill structures

Material characterization and precise finite element analysis of fiber reinforced thermoplastic composites for 4D printing

Physics-informed machine learning enabled virtual experimentation for 3D printed thermoplastic

An Artificial-intelligence/Statistics Solution to Quantify Material Distortion for Thermal Compensation in Additive Manufacturing

A Sensitivity Analysis-Based Parameter Optimization Framework for 3D Printing of Continuous Carbon Fiber/Epoxy Composites

Multimaterial direct 4D printing of high stiffness structures with large bending curvature