Abstract:Different types of ibuprofen-loaded, poly (D,L lactic-co-glycolic acid) (PLGA)-based implants were prepared by 3D printing (Droplet Deposition Modeling). The theoretical filling density of the mesh-shaped implants was varied from 10 to 100%. Drug release was measured in agarose gels and in well agitated phosphate buffer pH 7.4. The key properties of the implants (and dynamic changes thereof upon exposure to the release media) were monitored using gravimetric measurements, optical microscopy, Differential Scanning Calorimetry, Gel Permeation Chromatography, and Scanning Electron Microscopy. Interestingly, drug release was similar for implants with 10 and 30% filling density, irrespective of the experimental set-up. In contrast, implants with 100% filling density showed slower release kinetics, and the shape of the release curve was altered in agarose gels. These observations could be explained by the existence (or absence) of a continuous aqueous phase between the polymeric filaments and the "orchestrating role" of substantial system swelling for the control of drug release. At lower filling densities, it is sufficient for the drug to be released from a single filament. In contrast, at high filling densities, the ensemble of filaments acts as a much larger (more or less homogeneous) polymeric matrix, and the average diffusion pathway to be overcome by the drug is much longer. Agarose gel (mimicking living tissue) hinders substantial PLGA swelling and delays the onset of the final rapid drug release phase. This improved mechanistic understanding of the control of drug release from PLGA-based 3D printed implants can help to facilitate the optimization of this type of advanced drug delivery systems.

Study on Biodegradable Implant with Poly (L-Lactic Acid) and Its Releasing Character in Vitro

Histological Evaluation of Osteogenesis of 3D-Printed Poly-Lactic-Co-Glycolic Acid (plga) Scaffolds in A Rabbit Model

3D Printing and Coating to Fabricate a Hollow Bullet-Shaped Implant with Porous Surface for Controlled Cytoxan Release

Proliferation and Differentiation of Human Osteoblasts Within 3D Printed Poly-Lactic-co-Glycolic Acid Scaffolds

Poly(caprolactone)-Based Coatings on 3D-Printed Biodegradable Implants: A Novel Strategy to Prolong Delivery of Hydrophilic Drugs

Characteristics of Biodegradable Implantable Drug Delivery System with Micro-Porous Structure

3D Printing Surgical Implants at the Clinic: A Experimental Study on Anterior Cruciate Ligament Reconstruction

Poly(DL-Lactide) Polymer Blended with Mineral Phases for Extrusion 3D Printing—Studies on Degradation and Biocompatibility

The Effects of Structural & Materials Design on the Mechanisms of Tissue Integration with the 3D Printed Polyether-Ether-Ketone Cranial Implants in Vivo

Levofloxacin implants with predefined microstructure fabricated by three-dimensional printing technique.

Preparation and performance of poly (vinyl alcohol)/polylactic acid/hydroxyapatite composite scaffolds based on 3D printing

A Novel of Biodegradable Implants Based on Plga for Control Delivery of Cisplatin

The 3-Dimensional Simulation Of A Novel Degradable Implantable Controlled Drug Delivery

In vitro degradation and release characteristics of biodegradable implants containing trypsin inhibitor

Fabrication Of Biodegradable Polymer (Plga) Microstructures And Applications In Controlled Drug Delivery

Mechanical Properties and in Vitro Evaluation of Bioactivity and Degradation of Dexamethasone-Releasing Poly-D-l-lactide/nano-hydroxyapatite Composite Scaffolds

3D-Printed Polycaprolactone-Chitosan Based Drug Delivery Implants for Personalized Administration

Correlative Image-Based Release Prediction and 3D Microstructure Characterization for a Long Acting Parenteral Implant

Synthesis, characterization, and bioactivity investigation of biomimetic biodegradable PLA scaffold fabricated by fused filament fabrication process

Enhanced bioactivity of titanium-coated polyetheretherketone implants created by a high-temperature 3D printing process

3D printed PLGA implants: How the filling density affects drug release