Abstract:Fretting and corrosion of metallic medical devices are significant degradation mechanisms that impact performance. Multi-asperity contact surfaces undergo a progressive engagement-damage-redistribution process distributed over the nominal contact surface, implying that relatively short-lived fretting contact engagements of individual asperities are a central element to fretting corrosion processes in modular taper junctions of total hip replacements. In this work, the contact mechanics of single asperity hard-metal surfaces under small scale reciprocal sliding (SSRS) between two contacting surfaces in air and solution (i.e., tribocorrosion), typically less than 100 μm cyclic motion are presented and discussed for Ti–6Al–4V, CoCrMo, and 316L SS alloys. Characteristic scaling factors, based on asperity radius, hardness, and modulus, for characteristic stress and a dimensionless asperity radius are presented based on the interaction between elastic and plastic contact mechanics. The contact and tribological interactions of a 17 μm radius spherical diamond asperity was used to explore damage effects on these alloys in both air and phosphate buffered saline. The volume abraded, depth of penetration, extent of plastic deformation and oxide debris formation were captured as functions of cycles, load, and solution presence/absence. Damage was analyzed and quantified using digital optical microscopy, atomic force microscopy and scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS). The results were analyzed with ANOVA statistics (α < 0.05). The extent of damage follows CoCrMo < Ti–6Al–4V < 316L SS. The wear characteristics varied significantly between alloys with more plastic deformation associated with CoCr and more shearing particle and ribbon formation present for Ti–6Al–4V and 316L SS. Solution immersion did not significantly increase volume loss for any alloy but did increase the amount of released and embedded oxide debris for 316L SS. Titanium also exhibited oxide debris generation and embedding. Importantly, significant (<5 μm) penetration depths were obtained after 100 cycles, indicating that single asperities, continuously engaged with metal under very low loads, rapidly generate extensive debris and plastic deformation.

Evaluation of Protein Adsorption onto Stainless Steel 316L Surface Following a Tribological Test under Reciprocating Mode

Biotribological properties at the stem-cement interface lubricated with different media

Investigation Of Protein Adsorption Mechanism And Biotribological Properties At Simulated Stem-Cement Interface

The influence of protein concentration on the biotribological properties of the stem-cement interface

Tribological behavior of modified polyetheretherketone composites in sliding against stainless steel under water lubrication

Effective Adsorption of Functional Biological Macromolecules on Stainless Steel Surface with Micro/Nanoporous Texture

Protein-metal interactions due to fretting corrosion at the taper junction of hip implants: An in vitro investigation using Raman spectroscopy

Tribological Behavior of Ti-6Al-4V Against Cortical Bone in Different Biolubricants.

Influence of protein migration on the fretting-corrosion behavior of 316 L stainless steel with artificial crevices

An Investigation of the Antibacterial Ability and Cytotoxicity of A Novel Cu-Bearing 317l Stainless Steel

Performance of Austenitic High-Nitrogen Steels under Gross Slip Fretting Corrosion in Bovine Serum

MC3T3-E1 cell response to stainless steel 316L with different surface treatments

Friction and wear mechanisms in hip prosthesis: Comparison of joint materials behaviour in several lubricants

Investigating the Roles of Protein on the Cobalt Alloy Surface Degradation for Biomedical Implant Through Tribocorrosion Mechanisms

An investigation on the biotribocorrosion behaviour of CoCrMo alloy grafted with polyelectrolyte brush

Micro-asperity tribocorrosion of CoCrMo, Ti6Al4V, and 316 stainless steel in air and physiological solution: Small scale reciprocal sliding of a single diamond tip

Contact damage failure analyses of fretting wear behavior of the metal stem titanium alloy-bone cement interface

Tribological Behavior of 316L Stainless Steel Fabricated Using Metal Extrusion Additive Manufacturing Under Dry and Simulated Body Fluid‐Lubricated Conditions

Bioinspired Surface Functionalization of Titanium Alloy for Enhanced Lubrication and Bacterial Resistance

Tribo-electrochemical characterization of metallic biomaterials for total joint replacement

Study on the Friction and Wear Properties of PEEK Against Cortical Bone Tissue under Different Lubricating Conditions.