Abstract:The C-band deflecting cavity designed last year is finished. In this paper, the RF measurement of the cavity is introduced. After tuning, it works well at 5.712GHz with a coupling factor degree around 1.05. And we measured the electromagnetic field with bead-pull method. The flatness of the magnetic field is around 0.9, which is not ideal but meet the requirements of the bunch length measurement. And we propose a method of tuning to make sure both frequency and field flatness. INTRODUCTION The C-band deflecting cavity designed last year for the measurement of ultra-short electron beams is finished. It’s a standing wave RF deflecting structure consisting of 3 cells. This cavity is designed to operate at a frequency of 5.712GHz. In the second section of the paper, the design of the deflector is briefly introduced. RF measurement results are shown in the third part. And a new tuning method is discussed in the fourth part. RF DEFLECTOR DESIGN In our case, we choose a 3-cell SW structure to meet the required transverse deflecting voltage Vdef=1MV. The working mode is TM110 mode and π-mode. The 3D-model draw by CST is shown in Figure 1. Figure 1: 3D-design of the deflector. The main part of the model is composed of several cylinders. The radii of the cells are determined by both the frequency and magnet field flatness. And the length of central cell is determined by the working mode while the length of the end cells is determined by the results of particle dynamics[1]. In order to make sure the polarization direction not changed while two cell coupled, two end cells are slotted on the edges which are perpendicular to the direction we put the coupler. According to the discussion above, the dimensions of the cavity are shown in figure 2 and table 2. Figure 2: 3D-design of the deflector. Table 1: Dimensions of the RF Cavity Dimensions Value(mm) rm 30.85 dm 21.49 re 30.61 de 10.93 t 4.76 rb 8 rslot (not shown in figure 2) 3.5 According to the dimensions, it’s easy to get the cavity parameters such as the transverse shunt impedance. And table 3 shows the main parameters of the RF cavity. With 1 MW input power, the deflecting voltage can be 1.19 MV. Table 3: Cavity Parameters Parameters Value Q0 9003 RT/Q(MΩ) 156 RT(MΩ) 1.42 P(MW) 1 Vdef(MV) 1.19 ___________________________________________ *Work supported by NSFC 11375098 and 11327902 #jxp14@mails.tsinghua.edu.cn MOPMR060 Proceedings of IPAC2016, Busan, Korea ISBN 978-3-95450-147-2 386 C op yr ig ht © 20 16 C C -B Y3. 0 an d by th e re sp ec tiv e au th or s 06 Beam Instrumentation, Controls, Feedback and Operational Aspects T03 Beam Diagnostics and Instrumentation In table 3, we are more concerned about RT/Q which has little change after machining. And we can evaluate the real deflecting voltage by measuring the quality factor Q0 by equation 1

Experimental Analysis of A New Retarding Field Energy Analyzer

Novel Type of Retarding Field Energy Analyzer for Electron Beam Measurement of Traveling Wave Tube

Experiment for Evaluating a K -Band Space TWT Electron Beam

Design and Experimental Demonstration of a Circular Beam Electron Gun and a PPM System for D-Band TWTs

Design and Analysis of Electron Beam of 0.67 THz Traveling Wave Tube

A New Measurement Of Electron Beam Emittance With Cerenkov Radiation "Double Imaging" Method

Analysis of fringe field effects on measurement errors for Q-scanning-based emittance diagnosis system

Miniature Electrostatic Electron Energy Analyzers and S-shaped Deflector

Generation of Uniform Transverse Beam Distributions for High-Energy Electron Radiography

Beam distribution reconstruction simulation for electron beam probe

Comparison of electron cloud mitigating coatings using retarding field analyzers

Development of 1.3 GHz Medium-β (β = 0.634) Disk-Loaded Deflecting Cavity for 150 Kev Electron Beam

A Beam Phase and Energy Measurement Instrument Based on Direct RF Signal IQ Undersampling Technique

A Proximal Retarding Field Analyzer for Scanning Probe Energy Loss Spectroscopy

High Energy Electron Radiography System Design and Simulation Study of Beam Angle-Position Correlation and Aperture Effect on the Images

Generation and Stable Transmission of Miniature Electron Beams for 0.65-THz Traveling Wave Tubes

Design of a Sheet-Beam Electron Gun for a Ka-band Microfabricated Traveling-Wave Tube

Single-Shot Spatial-Temporal Electric Field Measurement Of Intense Terahertz Pulses From Coherent Transition Radiation

C-Band Deflecting Cavity for Bunch Length Measurement of 2.5 MeV Electron Beam

Time resolved energy spectrum diagnostics for 2MeV injector pulsed electron beam

Ultrafast High Energy Electron Lens Radiography Suitable for Transient Electromagnetic Field Diagnosis