Abstract:High-performance engineering thermoplastics offer lightweight and excellent mechanical performance in a wide temperature range. Their composites with carbon nanotubes are expected to enhance mechanical performance, while providing thermal and electrical conductivity. These are interesting attributes that may endow additional functionalities to the nanocomposites. The present work investigates the optimal conditions to prepare polyether ether ketone (PEEK)/multi-walled carbon nanotube (MWCNT) nanocomposites, minimizing the MWCNT agglomerate size while maximizing the nanocomposite electrical conductivity. The aim is to achieve PEEK/MWCNT nanocomposites that are suitable for melt-spinning of electrically conductive multifilament's. Nanocomposites were prepared with compositions ranging from 0.5 to 7 wt.% MWCNT, showing an electrical percolation threshold between 1 and 2 wt.% MWCNT (107–102 S/cm) and a rheological percolation in the same range (1 to 2 wt.% MWCNT), confirming the formation of an MWCNT network in the nanocomposite. Considering the large drop in electrical conductivity typically observed during melt-spinning and the drawing of filaments, the composition PEEK/5 wt.% MWCNT was selected for further investigation. The effect of the melt extrusion parameters, namely screw speed, temperature, and throughput, was studied by evaluating the morphology of MWCNT agglomerates, the nanocomposite rheology, and electrical properties. It was observed that the combination of the higher values of screw speed and temperature profile leads to the smaller number of MWCNT agglomerates with smaller size, albeit at a slightly lower electrical conductivity. Generally, all processing conditions tested yielded nanocomposites with electrical conductivity in the range of 0.50–0.85 S/cm. The nanocomposite processed at higher temperature and screw speed presented the lowest value of elastic modulus, perhaps owing to higher matrix degradation and lower connectivity between the agglomerates. From all the process parameters studied, the screw speed was identified to have the higher impact on nanocomposite properties.

Dramatic Effects of Scalable SNN‐Assisted Melt Dispersion on Thermal Conductivity and Coefficient of Thermal Expansion of Nanocomposites

Effects of Graphite Nanosheet Size on Thermal Storage Property of Composite PCMs

Effect of hybrid nanofillers on thermal conductivity of composite phase change materials

Enhanced Thermal Conductivity and Microwave Dielectric Properties by Mesostructural Design of Multiphase Nanocomposite

Enhanced composite thermal conductivity by percolated networks of in-situ confined-grown carbon nanotubes

Directional enhancement and potential reduction of thermal conductivity induced by one-dimensional nanoparticle addition in pure PCMs

Dispersion of CNT via an effective two-step method, and enhanced thermal conductivity of Mg composite reinforced by the dispersed CNT

Enhanced thermal conduction of hybrid filler/polydimethylsiloxane composites via a continuous spatial confining process

Molecular dynamics simulation on thermal enhancement for carbon nano tubes (CNTs) based phase change materials (PCMs)

Synergistically Improving the Thermal Conductivity and Mechanical Strength of PEEK/MWCNT Nanocomposites by Functionalizing the Matrix with Fluorene Groups

Insight into the mechanical properties and thermal expansion behavior of epoxy nanocomposites reinforced with multi‐walled carbon nanotube solvent‐free nanofluids

Thermal conductive segregated multi-scale network constructed by ball-milling and in-situ polymerization in PEEK/MWCNT/graphite composite

Nanoscale Dispersion of Carbon Nanotubes in a Metal Matrix to Boost Thermal and Electrical Conductivity via Facile Ball Milling Techniques

High-Performance PEEK/MWCNT Nanocomposites: Combining Enhanced Electrical Conductivity and Nanotube Dispersion

Influences of Carbon Nanotube Networking on the Conductive, Crystallization, and Thermal Expansion Behaviors of Pa610-Based Nanocomposites

Mechanical, thermal and morphological characterization of polycarbonate/oxidized carbon nanofiber composites produced with a lean 2-step manufacturing process.

Simultaneous Ultrasonication‐assisted Internal Mixing to Prepare MWCNTs‐filled Epoxy Composites with Increased Strength and Thermal Conductivity

Decoupled trends for electrical and thermal conductivity in phase-confined CNT co-continuous blends

Dramatic mechanical and thermal increments of thermoplastic composites by multi-scale synergetic reinforcement: Carbon fiber and graphene nanoplatelet

Preparation of MWCNTs/CF/PEEK Multi-Scale Composites with Good Mechanical and Electrical Conductivity by a Two-Step Process of AFP and Out-of-autoclave Tempering

Improving electromagnetic engineering of thermal conductive composites by establishing continuous thermal conductive networks with gradient impedance