Abstract:Sludge conditioning by the Fenton process can effectively reduce sludge water content. The Fenton process has ideal dewaterability at different initial pH levels. However, the difference in the initial pH levels can lead to variations in conditioner dosage, resulting in different environmental impacts and economic pressures. This study provides insights into the role of the life cycle linked response surface methodology (LC-RSM) framework in revealing optimal solutions with both environmental and economic performance in different combinations of conditioners. Response surface methodology (RSM) was used to construct a model of sludge dewatering by the Fenton process, and life cycle assessment and life cycle cost were used to quantify the environmental and economic performance of all conditioning solutions in the model. The LC-RSM optimization solution was 6%–68% and 15%–70% lower than the RSM recommended solution in terms of environmental impacts and economic costs, respectively. For specific impact categories, such as global warming potential, the LC-RSM optimization solution was 19%–56% lower than the RSM recommended solution. In addition, the total environmental impact of the different conditioner combinations ranged between 4.1 and 7.8 Pt and 3.2–6.7 Pt at 53% and 58% of the sludge target water content, respectively. Surprisingly, the environmental impact of the solution with superior dewatering performance (53%) was lower than that of the solution with poor dewatering performance (58%) in many cases. The above results show that the LC-RSM optimization solution has better environmental and economic performance compared to RSM. In addition, the environmental impacts and economic costs of different solutions with the same water content target vary widely, which may lead to comparing sludge conditioning procedures with different targets in an unfair environment. Therefore, a unified platform for comparison is needed, and LC-RSM can provide support. This study can assist decision-makers in identifying the best solution for both environmental and economic performance in a multivariate system and stimulate further discussion on how to compare different processes on a more uniform platform.

Improving the Simultaneous Removal of Chemical Oxygen Demand and Terephthalic Acid in A Cross-Flow Aerobic Sludge Reactor by Using Response Surface Methodology

Improving the Simultaneous Removal Efficiency of COD and Color in a Combined HABMR–CFASR System Based MPDW. Part 1: Optimization of Operational Parameters for HABMR by Using Response Surface Methodology

Performance of a Novel HABR–CFASR System for the Biological Treatment of Mixed Printing and Dyeing Wastewater (MPDW)

Optimization of operating parameters for sludge process reduction under alternating aerobic/oxygen-limited conditions by response surface methodology.

Optimization of Volatile Fatty Acid Production with Co-Substrate of Food Wastes and Dewatered Excess Sludge Using Response Surface Methodology

Optimization of wet air oxidation of cationic red X-GRL wastewater by response surface methodology

Optimization of Coagulation–flocculation Process for Papermaking-Reconstituted Tobacco Slice Wastewater Treatment Using Response Surface Methodology

Landfill Leachate Pretreatment by Coagulation–flocculation Process Using Iron-Based Coagulants: Optimization by Response Surface Methodology

Optimization of Operating Conditions for the Acidification Metabolites Production with Waste Sludge Using Response Surface Methodology (RSM).

Optimization for Removal of COD and BOD through RSM-CCD by Activated Sludge Treatment Process for Pharmaceutical Wastewater

Optimization of the Anaerobic-Anoxic-Oxic Process by Integrating ASM2d with Pareto Analysis of Variance and Response Surface Methodology

Parameter Optimization of Excess Sludge Treatment by Supercritical Water Oxidation

Investigation and optimization of the novel UASB-MFC integrated system for sulfate removal and bioelectricity generation using the response surface methodology (RSM).

A synergistic approach combining computational fluid dynamics simulation with hydrolysis-acidification for dye wastewater treatment

Optimization of a Completely Mixed Anaerobic Biofilm Reactor (CMABR), Based on Brewery Wastewater Treatment

Improving the Removal of Anionic Surfactant in Cardboard Industry Wastewater by Coagulation/Flocculation: Process Optimization with Response Surface Methodology

Optimization of supercritical water oxidation for coal-gasification wastewater treatment using response surface methodology

Optimization of Coagulation–flocculation Process for Combined Sewer Overflow Wastewater Treatment Using Response Surface Methodology

Treatment Of Printing And Dyeing Wastewater By A Submerged Double-Shaft Rotary Anaerobic Membrane Bioreactor

Revealing the best solution simultaneously for environmental and economic performance using response surface methodology under the perspective of life cycle: A case study of sludge dewatering by the Fenton process

Optimization of electro-oxidation and electro-coagulation combination process for landfill leachate advanced treatment by response surface methodology