Abstract:The paper is concerned with the modeling of the behaviour of welds when subjected to severe thermal and mechanical loads where the maximum temperature during dwell periods lies in the creep range. The methodology of the life assessment method R5 is applied where the detailed calculations are carried out using the linear matching method (LMM), with the objective of generating an analytic model. The linear matching method has been developed to allow accurate predictions using the methodology of R5, the UK life assessment method. The method is here applied to a set of weld endurance tests, where reverse bending is interrupted by creep dwell periods. The weld and parent material are both Type 316L(N) material, and data were available for fatigue tests and tests with 1 and 5h dwell periods to failure. The elastic, plastic, and creep behavior of the weld geometry is predicted with the LMM using the best available understanding of the properties of the weld and parent material. The numerical results are translated into a semi-analytic model. Using the R5 standard creep/fatigue model, the predicted life of the experimental welds specimens are compared with experimental data. The analysis shows that the most severe conditions occur at the weld/parent material interface, with fatigue damage concentrated predominantly in the parent material, whereas the creep damage occurs predominantly in the weld material. Hence, creep and fatigue damage proceed relatively independently. The predictions of the model are good, except that the reduction in fatigue life due to the presence of the weld is underestimated. This is attributed to the lack of separate fatigue date for the weld and parent material and the lack of information concerning the heat affected zone. With an adjustment of a single factor in the model, the predictions are very good. The analysis in this paper demonstrates that the primary properties of weld structures may be understood through a number of structural parameters, defined by cyclic analysis using the linear matching method and through the choice of appropriate material data. The physical assumptions adopted conform to those of the R5 life assessment procedure. The resulting semi-analytic model provides a more secure method for extrapolation of experimental data than previously available.

On Creep-Fatigue Endurance of TIG-dressed Weldments Using the Linear Matching Method

A parametric study on creep‐fatigue endurance of welded joints

Linear Matching Method for Parametric Studies of Weldments Creep-Fatigue Endurance

Application of Linear Matching Method to Creep–fatigue Failure Analysis of Cruciform Weldment Manufactured of Austenitic Steel AISI Type 316N(L)

Creep-fatigue life assessment of cruciform weldments using the linear matching method

A parametric study on creep-fatigue strength of welded joints using the linear matching method

Modeling of the Behavior of a Welded Joint Subjected to Reverse Bending Moment at High Temperature

Experimental and Numerical Characterization of Low Cycle Fatigue and Creep Fatigue Behaviour of P92 Steel Welded Joint

Creep-fatigue Life Assessment of High-Temperature Weldments Using the Linear Matching Method

Creep-fatigue Properties and Deformation Mechanism of 316L Steel Fabricated by Laser Powder Bed Fusion (PBF-LB/M)

Characterization of the Cyclic Softening and Remaining Creep Behaviour of P92 Steel Weldment

Remaining creep properties and fracture behaviour of P92 steel welded joint under prior low cycle fatigue loading

An Insight into the Creep-Fatigue Damage Localization in Welded Joints Based on Crystal Plasticity Finite Element Method

The correlation between prior fatigue damage and remaining creep properties in a high chromium steel welded joint

On Creep Fatigue Interaction of Components at Elevated Temperature

Creep Fatigue Damage Assessment Of V-Butt Weld Pipe With An Extended Direct Steady Cycle Analysis

Fatigue-Creep Interaction Of P92 Steel And Modified Constitutive Modelling For Simulation Of The Responses

Research on Fatigue-Creep Interaction Damage of Steel 1.25Cr0.5mo

Fatigue performance assessment of thick TIG-Dressing cruciform welded joints made by Q355D structural steel

Fatigue Crack Growth Rates of 10crni3mov Steel Welded Joints Considering the Stress Ratio

Creep–Cyclic Plasticity and Damage Assessment of an SS304 Weldolet