Abstract:Integrated tubing can be used in the process of both fracturing and production for the oil and gas industry. During the process of fracturing, the inner surface of the tubing is subjected to the erosion from the slurry with sand and fracturing fluid, and then in the process of production, it is also corroded by the high-CO2-containing multiphase medium. To evaluate the CO2 corrosion resistance of Super 13Cr tubing after erosion in fracturing, the erosion test of Super 13Cr tubing under different impact angles was carried out by the jetting facility. For the samples with different erosion damage, the high-temperature and high-pressure CO2 corrosion experiments were carried out. The CO2 corrosion morphology with different erosion damage was also analyzed by SEM. The results show that different erosion damage at different impact angles can affect the corrosion rate in the later CO2 corrosion test. At an impact angle of 30°, the erosion damage is mainly caused by the cutting and plowing mechanisms by the eroded particles. The craters and folded extruded lips on the surface of the Super 13Cr tubing are formed and the passive film of super 13Cr is removed on the bottom of the craters, resulting in a corrosion rate that was approximately 1.4 times greater than that of the non-eroded surface. However, at the impact angle of 90°, the erosion mechanism is the plastic deformation and many platelets are formed. Less contact area between the fresh surface without passive film and the corrosive medium results in a lower corrosion rate than the material with 30° impact erosion damage.

Investigation of Stress Corrosion Cracking Behavior of Super 13cr Tubing by Full-Scale Tubular Goods Corrosion Test System

Stress corrosion cracking behavior of super 13Cr tubing in phosphate packer fluid of high pressure high temperature gas well

Study on Fracture Failure Behavior of Super 13Cr Tubing Caused by Deposited Corrosion

Behavior of Corroded Thin-Walled Concrete-Filled Steel Tubular Stub Columns

Crack Propagation and Flexural Behaviour of Rc Beams under Simultaneous Sustained Loading and Steel Corrosion

Investigation of Multi-Factor Stress Corrosion Cracking Failure of Safe-End Feedwater Lines of Submarine Power System

Corrosion Development of Carbon Steel Grids and Shear Connectors in Cracked Composite Beams Exposed to Wet-Dry Cycles in Chloride Environment.

Peridynamic Investigation of Stress Corrosion Cracking in Carbon Steel Pipes

Farm Level Indicators of Sustainable Land Management for the Development of Decision Support Systems

Initiation of Stress Corrosion Cracks in X80 and X100 Pipe Steels in Near-Neutral Ph Environment

Corrosion Behavior of Tubing in High-Salinity Formation Water Environment Containing H2S/CO2 in Yingzhong Block

An Investigation of Corrosion-Induced Stress During SCC

Experimental Study on CO2 Corrosion of Super 13Cr Integrated Tubing with Erosion Damage

Corrosion behavior of T91 tubing in high temperature supercritical carbon dioxide environment

Microstructural Effects in the Development of Near-Neutral pH Stress Corrosion Cracks in Pipelines

Failure analysis of a high strength Cr-containing tube used in an oil well

Stress Corrosion Cracking of E690 Steel As a Welded Joint in a Simulated Marine Atmosphere Containing Sulphur Dioxide

Observations of Stress Corrosion Cracking in Pipeline Steel in Corrosive Seawater Environment Including Detailed Observation of the Crack Initiation Mechanism

Analysis of Stress Corrosion Cracking Growth Rate in the Heat-Affected Zone of 316L Based on the Heterogeneity of the Mechanical Properties

Study on Stress Corrosion Cracking Behavior of Incoloy825/X65 Bimetallic Composite Pipe Welded Joint in Wet Hydrogen Sulfide Environment

Analysis of the causes of the cracking of tube bundles of 316L stainless steel Shell-and-Tube heat exchanger