Abstract:beta-solidifying gamma-TiAl alloys have attracted much attention for their higher specific strength and better mechanical properties at elevated temperature. They usually need some boron addition to refine the lamellar grain size, which is believed to improve their poor room temperature ductility. However, the boron addition may cause some side effects on mechanical properties for the formation of borides with unfavorable morphology and crystal structure, which is severely influenced by the alloy composition and cooling rate during casting. The components of gamma-TiAl applied usually have complex structure, such as different thicknesses, which leads to different cooling rates and therefore different microstructures and mechanical properties. To evaluate the influence of cooling rate on the microstructure and mechanical properties of gamma-TiAl investment casting, plate with step thicknesses was designed to achieve different cooling rates. Step plates of beta-solidifying boron-containing TiAl alloy were fabricated by centrifugal casting in Y2O3 facing coating ceramic moulds. It was found that boride mainly distributed on grain boundary, and its aspect ratio increased with increasing cooling rate, with its morphology varying from short, flat plate to long, curvy ribbon. The short plate and curvy ribbon borides were TiB with B27 and B structure, respectively. Both types of boride exhibit anisotropic growth characteristics (especially for B, structure), with the slowest growth rate along [100] and [010] for B27 structure and B, structure, respectively. This is attributed to the difficulty of atomic rearrangement along corresponding directions during solidification. The cooling rate increase caused the increase of yield strength but the decrease of room temperature ductility, the former results from the decreasing of grain size and lamellar spacing, while the latter results from the easy cracking nucleation and propagation of the long curvy boride, leaving smooth curvy surfaces on the fracture surface. Samples containing short flat plate boride showed better ductility, and no smooth curvy surface was observed.

Effect of power on microstructure and mechanical properties of Ti44Al6Nb1.0Cr2.0V0.15Y0.1B alloy prepared by cold crucible directional solidification

Investigation of macro/microstructure evolution and mechanical properties of directionally solidified high-Nb TiAl-based alloy

Effect of Trace Boron Addition on the Microstructural Evolution and Mechanical Properties in Ti45al8nb2cr-B Alloys

Effects of Solidification Rates on Microstructure Refinement and Elemental Distribution of Ti44Al6Nb1.0Cr2.0V0.1B0.15Y Alloy by Rapid Solidification

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Microstructural evolution and mechanical properties of a Cr-rich β-solidifying TiAl-based alloy prepared by electromagnetic cold crucible continuous casting

Microstructure refinement and improvement of mechanical properties of Ti46Al8Nb0.9B alloys by electromagnetic cold crucible continuous solidification

Effect of cooling rate on solidification microstructure and mechanical properties of TiB2-containing TiAl alloy

Effects of Nb/Ti additions and heat treatment on the microstructure evolution and hardness of as-cast and directionally solidified NiAl–Cr(Mo) alloy

Effect of Growth Rate on Microstructure and Mechanical Properties in a Directionally Solidified Nb-silicide Base Alloy

Study on improving directional microstructure of Ti44Al6Nb1Cr alloy by continuous regional phase transformation

Optimizing microstructure and mechanical properties of directionally solidified Ti44Al6Nb1Cr2V alloy by directional heat treatment

[Liver cirrhosis in young calves].

Temperature-dependent Mechanical Properties and Fracture Behavior of Directionally Solidified Ti47Al2Cr2Nb Alloy

Effect of Cooling Rate on Boride and Room Temperature Tensile Properties of Β-Solidifying Γ-Tial Alloys

Enhanced fracture toughness stability of (B,Y)-contained TiAl-based alloy prepared by cold crucible directional solidification

On the Orientation Relationship Between Ti5Si3 Precipitates and B2 Phase in a Ti-47Al-2W-0.5Si Alloy

Microstructure and Mechanical Properties of the Powder Metallurgy Nb-16Si-24Ti-2Al-2Cr Alloy

Effect of Al content on the hot deformation behavior and microstructure evolution of TiAl-6(Cr, Nb, Ta) alloy

Microstructure and Elevated Temperature Tensile Behaviour of Directionally Solidified Nickel Based Superalloy

Evaluation of Microstructure and Mechanical Properties of TiAl/HI-TEMP 820/ SCM440H Materials Manufactured through Vacuum Brazing according to Process Temperature