Abstract:In a circulating fluidized bed (CFB) boiler, one of the basic functions of the bed materials is to transport heat between different parts of the boiler to clecrease heat gradients and, thereby, smoothen the operation. A novel concept, oxygen Carrier-aided combustion (OCAC), replaces some or all of the bed materials with an oxygen carrier, which is a metal oxide that, through chemical redox reaction, not only transports heat but also transports oxygen between oxygen-lean and oxygen-rich areas of the boiler. The oxygen carrier also acts as internal oxygen storage, which increases the total amount of available oxygen in the boiler. The concept of OCAC was demonstrated by Thunman et al. at Chalmers University of Technology, where the bed material (sand) in a 12 MW boiler was replaced with iron titanium mineral (ilmenite). In this work, a small fluidized bed reactor is used to mimic the condition in OCAC with regard to fuel conversion as well as NO formation and to test other oxygen carrier, materials. Four oxygen carriers were tested, two ores (ilmenite and manganese ore), and two Oxide scales (denoted as AQS and LDst), which were byproducts from the steel production of the Swedish company SSAB. Sand was also used as a reference. Wood char was used as the fuel, and concentrations of CO2, CO, CH4, O-2, and NO in the exhaust gases were monitored. The effect of oxygen carriers on combustion efficiency and NO emission was investigated at different air/fuel ratios. The results Show that, utilization of an oxygen carrier reduces the level of CO emission, thereby increasing the efficiency of combustion. It is also Shown that the increase In combustion efficiency can be largely attributed to the reactivity of the oxygen carriers with CO. With OCAC, it was possible to reduce the level of excess air and, thereby, lower the level of NO emissions while maintaining the same level of CO emission.

Influence of O2/CO2 Mixtures on the Fluid-Dynamics of an Oxy-Fired Fluidized Bed Reactor

Measurements and Modelling of Oxy-Fuel Coal Combustion

Modeling Agglomeration Behavior in High Temperature Gas–Solid Fluidized Beds Via Monte Carlo Method

Three-dimensional Modeling Study of the Oxy-Fuel Co-Firing of Coal and Biomass in a Bubbling Fluidized Bed

Mathematical modeling of combustion in a grate-fired boiler burning straw and effect of operating conditions under air- and oxygen-enriched atmospheres

Flamelet LES of a 40 Kwth Pulverized Torrefied Biomass Furnace in Air and Oxy-Fuel Atmospheres

Oxy-coal combustion in an entrained flow reactor: Application of specific char and volatile combustion and radiation models for oxy-firing conditions

Modeling of Single Coal Particle Combustion in O2/N2 and O2/CO2 Atmospheres under Fluidized Bed Condition

Modeling of Oxidative Coupling of Methane for Manufacture of Olefins—Part I: CFD Simulations

Effective lateral dispersion of momentum, heat and mass in bubbling fluidized beds

Numerical investigation of the oxy-fuel combustion in the fluidized bed using macroscopic model supported by CFD-DDPM

Optimizing injection modes and reactor shapes in gas-particle fluidized beds using a mesoscale CFD model

Impact of Operating Parameters on Biomass Gasification in a Fluidized Bed Reactor: an Eulerian-Lagrangian Approach

Kinetic Model Implementation of Fluidized Bed Devolatilization

Numerical study of the gas–solid flow pattern in methanol to olefiens fluidized bed reactor: Cold model

Combustion Interactions of Blended Coals in an O-2/CO2 Mixture in a Drop Tube Furnace: Experimental Investigation and Numerical Simulation

Oxygen-Carrier-Aided Combustion in a Bench-Scale Fluidized Bed

Computational Fluid Dynamics Simulation of a High-Throughput Catalytic Fixed-Bed Reactor for Total Oxidation of Methane

High-pressure Laminar Flame Speeds and Kinetic Modeling of Carbon Monoxide/hydrogen Combustion

Numerical Predictions on the Influences of Inlet Temperature and Pressure of Feed Gas on Flow and Combustion Characteristics of Oxy-pulverized Coal Combustion

KINETIC MODEL PREDICTION FOR VARIOUS COAL GASIFICATION SCHEMES IN A FLUIDIZED BED II. MODEL PREDICTION AND ANALYSIS