Abstract:Over time, with the increase in population and the subsequent increase in energy consumption and also due to the non-renewability of fossil fuels, the study of alternative fuels has increased. One of these fuels is biodiesel, which is a suitable alternative to fossil fuels such as diesel and received much attention from researchers today. For this reason, measuring the physical properties of biodiesel is of great importance. Due to the high cost and time-consuming nature of laboratory methods, numerical methods are used to estimate material properties. The novelty of this research was the use of two white box models, including Group method of data handling (GMDH) and Gene expression programming (GEP), which work on the basis of artificial intelligence. By using these models, two simple mathematical equations with high accuracy were presented to predict the surface tension of biodiesel. These models can be used at different temperatures and molecular weights. To do modeling, 78 laboratory data available in the literature were gathered and the data were randomly divided into two groups, train and test, in a ratio of 80 and 20. The input parameters include mass fraction of fatty acid ethyl esters and temperature (T), and esters are divided into three groups according to their molecular weight: less than 200 (Mw1), between 200 and 300 (Mw2), and greater than 300 (Mw3). The statistical error parameters were calculated for the two models developed in this research and after comparing the results, it was found that the GMDH model estimates the surface tension of biodiesel with a higher accuracy. The average absolute relative error for GMDH and GEP models was reported as 0.97 and 1.89, respectively. Also, other statistical error parameters of GMDH such as RMSE, SD, and R2 for the GMDH model were obtained as 0.444, 0.000233, and 0.9233, respectively. Moreover, sensitivity analysis showed that temperature has the highest impact on the surface tension of biodiesel, which is also an inverse effect. Finally, suspicious laboratory and outlier data points were identified using the Leverage technique. According to this analysis, only five data points were identified as outliers and suspicious laboratory data.

Predicting the vapor pressure of fatty acid esters in biodiesel by group contribution method

Measurement and Correlation of the Density, Viscosity and Vapor Pressure of Fatty Acid 2-Ethyhexyl Esters

Calculations of Physical Properties and Phase Equilibrium in Polyethylene Glycol Terephthalate Esterification System

Measurements and Correlations of Density, Viscosity, and Vapor Pressure for Methyl Ricinoleate

Using the group contribution method to predict the flash temperature of biodiesel and ethanol mixtures

Isobaric Vapor–Liquid Equilibrium of the Mixture of Methyl Palmitate and Methyl Stearate at 0.1 kPa, 1 kPa, 5 kPa, and 10 kPa

Skeletal Mechanism Construction for Heavy Saturated Methyl Esters in Real Biodiesel Fuels

Study on volatility and flash point of the pseudo binary mixtures of sunflower-based biodiesel + methylcyclohexane

Predicting the surface tension of biodiesel fuels by a mixture topological index method, at 313 K

Kinetics of glycerol esterification reaction

Study on volatility and flash point of the pseudo-binary mixtures of sunflowerseed-based biodiesel + ethanol

Experimental investigation of liquid thermal diffusivity for fatty acid methyl/ethyl esters by dynamic light scattering method

Experimental and Modeling Investigations of Density and Viscosity for the Ternary ( N -Octane + Ethylcyclohexane + Ethylbenzene) Mixtures

Volatility of Blended Fuel of Biodiesel and Ethanol

Molecular dynamics study of the thermodynamic properties of triglyceride/methanol mixtures in the presence of cosolvent

Measurements on vapor pressure and thermal conductivity for pseudo-binary systems of a hydrocarbon fuel with ethylene and diethylene glycol dimethyl ethers

On the evaluation of surface tension of biodiesel

Effects of unsaturated fatty acid methyl esters on the oxidation stability of biodiesel determined by gas chromatography-mass spectrometry and information entropy methods

Determination of vapour pressures of FAME industrial mixtures by ebullioscopic and thermogravimetric experimental methods

Densities and Viscosities for the Ternary Mixture of N-Undecane (1) + Methyl Decanoate (2) + N-Butanol (3) and Corresponding Binaries from T=293.15 to 333.15 K and at Atmospheric Pressure

Experimental and Modeling Efforts Towards a Better Understanding of the High-Temperature Combustion Kinetics of C3C5 Ethyl Esters