Rapid Determination of Plutonium in Water Samples Using Vacuum Box System Separation and Low Background Liquid Scintillation Counter Measurement

Bo Liu,Keliang Shi,Gaoyang Ye,Yaming Li,Wangsuo Wu

DOI: https://doi.org/10.1039/c5ay02232k

IF: 3.1

2015-01-01

Analytical Methods

Abstract:An analytical method for rapid determination of 239+240plutonium in environmental liquid samples was developed.

What problem does this paper attempt to address?

Determination of Plutonium Isotopes (238pu, 239pu, 240pu, 241pu) in Environmental Samples Using Radiochemical Separation Combined with Radiometric and Mass Spectrometric Measurements

Yihong Xu,Jixin Qiao,Xiaolin Hou,Shaoming Pan,Per Roos

DOI: https://doi.org/10.1016/j.talanta.2013.11.061

IF: 6.1

2014-01-01

Talanta

Abstract:This paper reports an analytical method for the determination of plutonium isotopes (238Pu, 239Pu, 240Pu, 241Pu) in environmental samples using anion exchange chromatography in combination with extraction chromatography for chemical separation of Pu. Both radiometric methods (liquid scintillation counting and alpha spectrometry) and inductively coupled plasma mass spectrometry (ICP-MS) were applied for the measurement of plutonium isotopes. The decontamination factors for uranium were significantly improved up to 7.5×105 for 20g soil compared to the level reported in the literature, this is critical for the measurement of plutonium isotopes using mass spectrometric technique. Although the chemical yield of Pu in the entire procedure is about 55%, the analytical results of IAEA soil 6 and IAEA-367 in this work are in a good agreement with the values reported in the literature or reference values, revealing that the developed method for plutonium determination in environmental samples is reliable. The measurement results of 239+240Pu by alpha spectrometry agreed very well with the sum of 239Pu and 240Pu measured by ICP-MS. ICP-MS can not only measure 239Pu and 240Pu separately but also 241Pu. However, it is impossible to measure 238Pu using ICP-MS in environmental samples even a decontamination factor as high as 106 for uranium was obtained by chemical separation.
Determination of Plutonium Isotopes (Pu-238, Pu-239, Pu-240, Pu-241) in Environmental Samples Using Radiochemical Separation Combined with Radiometric and Mass Spectrometric Measurements

Yihong Xu,Jixin Qiao,Xiaolin Hou,Shaoming Pan,Per Roos

DOI: https://doi.org/10.1016/j.talanta.2013.11.061

IF: 6.1

2014-01-01

Talanta

Abstract:This paper reports an analytical method for the determination of plutonium isotopes (Pu-238, Pu-239, Pu-240, Pu-241) in environmental samples using anion exchange chromatography in combination with extraction chromatography for chemical separation of Pu. Both radiometric methods (liquid scintillation counting and alpha spectrometry) and inductively coupled plasma mass spectrometry (ICP-MS) were applied for the measurement of plutonium isotopes. The decontamination factors for uranium were significantly improved up to 7.5 x 10(5) for 20 g soil compared to the level reported in the literature, this is critical for the measurement of plutonium isotopes using mass spectrometric technique. Although the chemical yield of Pu in the entire procedure is about 55%, the analytical results of IAEA soil 6 and IAEA-367 in this work are in a good agreement with the values reported in the literature or reference values, revealing that the developed method for plutonium determination in environmental samples is reliable. The measurement results of Pu239+240 by alpha spectrometry agreed very well with the sum of Pu-239 and Pu-240 measured by ICP-MS. ICP-MS can not only measure Pu-239 and Pu-240 separately but also Pu-241. However, it is impossible to measure Pu-238 using ICP-MS in environmental samples even a decontamination factor as high as 10(6) for uranium was obtained by chemical separation. (C) 2013 Elsevier B.V. All rights reserved.
Rapid and Simultaneous Determination of 238Pu, 239Pu, 240Pu, and 241Pu in Samples with High-Level Uranium Using ICP-MS/MS and Extraction Chromatography

Zhao Huang,Xiaolin Hou,Xue Zhao

DOI: https://doi.org/10.1021/acs.analchem.3c02526

2023-08-29

Abstract:As the most important plutonium isotopes, 238Pu, 239Pu, 240Pu, and 241Pu are normally measured by two to three techniques, which are tedious, time-consuming, and not suitable for rapid analysis in emergency situations. Recently, ICP-MS has become a competitive technique for the rapid measurement of 239Pu, 240Pu, and 241Pu. However, ICP-MS is difficult to measure 238Pu due to the serious isobaric interference of 238U. This work reports a rapid analytical method to solve this problem for the simultaneous determination of 238Pu, 239Pu, 240Pu, and 241Pu using triple-quadrupole inductively coupled plasma mass spectrometry (ICP-MS/MS) combined with chemical separation. Chemical separation achieved a high decontamination factor of 2.12 × 109 for the most critical interfering element, uranium, by using two sequential TK200 columns. The interferences of 238U1H+ and 238U+ were effectively eliminated by using 12 mL/min He-6 mL/min NH3 as the reaction gases in the octupole collision/reaction cell in ICP-MS/MS. Combined with chemical separation, the overall elimination efficiency of 238U1H+ reached 3.6 × 1017, which is 105 times better than the reported method. With the high 238U+ elimination efficiency of 1.12 × 104 in the ICP-MS/MS measurement, the overall removal efficiency of 238U+ reached 1013, guaranteeing accurate determination of femtogram-level 238Pu as well as 239Pu, 240Pu, and 241Pu in the samples containing milligram-level 238U. The detection time is reduced to minutes, well fulfilling the requirement of rapid analysis. This method is validated by analyzing the standard reference material and the spiked samples.
Rapid Determination of Ultra-Trace Plutonium Isotopes (239pu, 240pu and 241pu) in Small-Volume Human Urine Bioassay Using Sector-Field Inductively Coupled Plasma Mass Spectrometry.

Youyi Ni,Jian Zheng,Qiuju Guo,Wu Men,Keiko Tagami,Shigeo Uchida

DOI: https://doi.org/10.1016/j.aca.2017.10.012

IF: 6.911

2017-01-01

Analytica Chimica Acta

Abstract:A rapid method with enhanced 238U decontamination was developed for ultra-trace Pu analysis in small-volume urine bioassays. This method consists of acid digestion, co-precipitation, extraction chromatography and sector-field inductively coupled plasma mass spectrometry (SF-ICP-MS) measurement. Parameters that may influence the analytical performance were studied systematically. This method achieved a high 238U decontamination factor (3.8 × 106) and the 242Pu recovery was stable for 20 mL and 100 mL urine bioassays with an average value of 72.7 ± 5.5%. The limits of detection for 239Pu, 240Pu and 241Pu by the method were 0.016 fg mL-1, 0.016 fg mL-1 and 0.019 fg mL-1 for 20 mL urine samples and 0.003 fg mL-1, 0.002 fg mL-1 and 0.003 fg mL-1 for 100 mL urine samples, respectively. Considering the small volume of urine employed in this study, the absolute detection limits of the method were comparable or even better than those measured with thermal ionization mass spectrometry and accelerator mass spectrometry. All procedures for 20 mL and 100 mL urine bioassays were completed in 9.5 h and 11 h, respectively, and analysis of 10 samples could be finished within one day. With the considerably low detection limits of Pu isotopes and high sample throughput, this method would be a promising tool for the quick response to radiological emergencies and for rapid screening of unexpected occupational exposures of workers involved in the future FDNPP reactor decommissioning operations.
A Rapid Method for Quantification OF 242Pu in Urine Using Extraction Chromatography and ICP-MS

Athena Marie Gallardo,Chit Than,Carolyn Wong,Ralf Sudowe

DOI: https://doi.org/10.1097/HP.0000000000000607

Abstract:Occupational exposure to plutonium is generally monitored through analysis of urine samples. Typically, plutonium is separated from the sample and other actinides, and the concentration is determined using alpha spectroscopy. Current methods for separations and analysis are lengthy and require long count times. A new method for monitoring occupational exposure levels of plutonium has been developed, which requires fewer steps and overall less time than the alpha spectroscopy method. In this method, the urine is acidified, and a Pu internal standard is added. The urine is digested in a microwave oven, and plutonium is separated using an Eichrom TRU Resin column. The plutonium is eluted, and the eluant is injected directly into the Inductively Coupled Plasma-Mass Spectrometer (ICP-MS). Compared to a direct "dilute and shoot" method, a 30-fold improvement in sensitivity is achieved. This method was validated by analyzing several batches of spiked samples. Based on these analyses, a combined standard uncertainty plot, which relates uncertainty to concentration, was produced. The MDA95 was calculated to be 7.0 × 10 μg L, and the Lc95 was calculated to be 3.5 × 10 μg L for this method.
The DNA laboratory and neurological practice.

A. Harding

DOI: https://doi.org/10.1136/jnnp.56.3.229

1993-03-01

Journal of Neurology Neurosurgery & Psychiatry

Abstract:Molecular genetic techniques have already made an impact on neurological practice, leading to improved diagnosis and genetic counselling in inherited neurological disorders. The purpose of this review is to outline what the DNA laboratory can currently provide the neurologist, in terms of services to patients with neurological disease and their families. The first neurological disease to be assigned to a specific chromosomal region by means of random linkage analysis using variable DNA markers (polymorphisms) was Huntington's disease (HD).' Since then the neurological disease map has become much more dense2 (table 1). Also, several gene defects have been identified, either after gene mapping and subsequent gene isolation (reverse genetics, now known as positional cloning), such as, hereditary motor and sensory neuropathy (HMSN type Ia)34 or by direct analysis of candidate genes, for example, in some cases of familial Alzheimer's disease5 and inherited prion diseases6 (table 2). The small genome found in mitochondria has also been established as a mutation hot spot for some neurological diseases, a possibility suggested by their biochemical features and predominantly maternal mode of transmission.7
Rapid determination of plutonium isotopes in small samples using single anion exchange separation and ICP-MS/MS measurement in NH3–He mode for sediment dating

Yihong Xu,Chen Li,Haiping Yu,Fengman Fang,Xiaolin Hou,Chao Zhang,Xiaofei Li,Shan Xing

DOI: https://doi.org/10.1016/j.talanta.2021.123152

IF: 6.1

2022-04-01

Talanta

Abstract:To accurately determine ultra-trace Pu isotopes in small environmental samples, we explored ICP-MS/MS in NH3-He mode, and investigated mechanism of 238U interference removal and measurement sensitivity improvement for plutonium isotopes. The interference of uranium and uranium hydrides was effectively eliminated using 0.4 mL/min NH3 as reaction gas by shifting them to U(NHm)n+ and UH(NHm)n+. The overall interference of uranium was reduced to <2.4 × 10-7, while remaining excellent 239Pu sensitivity (13,900 Mcps/(mg/L)) mainly due to ion focusing effect of Pu by helium gas. On this basis, the purification of plutonium using a single AG1- × 4 column was proved to be sufficient for accurate determination of plutonium isotopes by the developed detection method, and the detection limits for the method were estimated to be 0.16 fg (0.4 μBq) for 239Pu, 0.046 fg (0.4 μBq) for 240Pu and 0.039 fg (0.15 mBq) for 241Pu. The method was validated by analyzing plutonium isotopes in certificated reference materials and reported environmental samples of only 1-2 g. The analytical results of ultra-trace Pu isotopes in small amounts (∼1 g) of lake sediments obtained by the developed method were successfully applied to sediment dating.

chemistry, analytical
Rapid Method for Sequential Determination of Pu and Am in Soil and Sediment Samples by Sector-Field Inductively Coupled Plasma Mass Spectrometry

Wang Zhongtang,Xie Yun,Lin Jinxian,Li Zejun,Tan Zhaoyi

DOI: https://doi.org/10.1007/s10967-021-07627-w

2021-01-01

Journal of Radioanalytical and Nuclear Chemistry

Abstract:New method was developed to analyze Pu and Am sequentially for soil and sediment by inductively coupled plasma mass spectrometry (ICPMS). The developed method uses conc. HNO3 to leach Pu and Am, Fe(OH)3 coprecipitation to remove alkali and alkaline metals, extraction chromatographic separation using UTEVA, DGA and TEVA resins to remove interfering elements (IEs) and separate Pu and Am from each other, and sector field-ICPMS to measure Pu and Am. The analysis of four standard reference materials showed that both Pu isotopes and 241Am were accurately determined by this method, as a result of its excellent decontamination ability of IEs. Especially the high decontamination factor of Pu [DF(Pu), 4.2 × 102] in Am fraction and high DF(Am) (7.0 × 103) in Pu fraction sufficiently eliminated the cross interference between 241Pu and 241Am in ICPMS measurement. In addition, stable and high chemical recoveries were achieved for Pu (71–91%) and Am (70–88%). The low LODs of Pu isotopes, short analytical time (14 h) and high DFs of IEs allows this method to sequentially analyze Pu and Am, for both global fallout and nuclear accident sourced samples.
Simultaneous determination of femtogram levels of 237Np, 239Pu, and 240Pu in environmental solid samples using extraction chromatography and ICP-MS/MS

Zhao Huang,Xiaolin Hou,Jixin Qiao,Xue Zhao

DOI: https://doi.org/10.1016/j.talanta.2023.124798

IF: 6.1

2023-12-01

Talanta

Abstract:An analytical method based on triple quadrupole inductively coupled plasma mass spectrometry (ICP-MS/MS) was developed for simultaneous determination of femtogram levels of 237Np, 239Pu, and 240Pu in environmental samples. By carefully controlling the valence states of Np and Pu in the entire separation procedure using a simple single extraction chromatographic column (TK200), the consistent behavior of Np and Pu was achieved, allowing for the reliable application of 242Pu as the chemical yield tracer for 237Np, 239Pu, and 240Pu. A high decontamination factor of 3.2 × 107 for the most critical interfering element, uranium, was achieved in the chemical separation step. The interferences of 238U1H+ and peak tailing of 238U+ during the measurement of plutonium isotopes were effectively eliminated by utilizing 7.5 mL/min He-1.1 mL/min CO2 as reaction gases in the octupole collision/reaction cell and employing sequential quadrupole mode for mass separation in ICP-MS/MS. Specifically, the interference of 238U1H+ was reduced to 10-6 and the peak tailing of 238U+ to 10-10, surpassing the performance of measurement method without reaction gases by 3 orders of magnitude. The developed method enables the accurate determination of femtogram levels of 237Np, 239Pu, and 240Pu in the samples with U/Np and U/Pu atom ratios of up to 1017 and 1012, respectively. The developed method was validated by analyzing standard reference materials and spiked soil samples.
Plutonium determination in seawater by inductively coupled plasma mass spectrometry: A review

Liguo Cao,Wenting Bu,Jian Zheng,Shaoming Pan,Zhongtang Wang,Shigeo Uchida

DOI: https://doi.org/10.1016/j.talanta.2016.01.010

IF: 6.1

2016-01-01

Talanta

Abstract:Knowing the concentration and isotopic ratio of Pu in seawater is of critical importance for assessing Pu contamination and investigating oceanic processes. In recent decades, the concentration of 239+240Pu in seawater, particularly for surface seawater, has presented an exponential decreasing trend with time; thus determination of Pu in seawater has become a challenge nowadays. Here, we have summarized and critically discussed a variety of reported analytical methods for Pu determination in seawater sample based on inductively coupled plasma mass spectrometry (ICP-MS) analytical technique for rapid ultra-trace detection of Pu. Generally, pretreatments for seawater sample include co-precipitation, valence adjustment and chemical separation and purification procedures, all of which are comprehensively reviewed. Overall, the selected anion-exchange, extraction resins and operation condition are important for decontamination of interference from matrix elements and achieving satisfactory chemical yields. In addition, other mass spectrometric and radiometric detections are briefly addressed and compared with the focus on assessing ICP-MS. Finally, we discuss some issues and prospects in determination and application of Pu isotopes in seawater samples for future research.
Solubility of Pu(IV)Under Simulated Geological Disposal Condition

LONG Hao-qi,ZHOU Duo,JIANG Tao,WANG Bo,YAO Jun,SONG Zhi-xin,BAO Liang-jin,CHEN Xi

DOI: https://doi.org/10.7538/hhx.2015.37.02.0115

2015-01-01

Abstract:Solubility of Pu (Ⅳ)was determined by oversaturation method under simulated disposal conditions.The underground anaerobic condition was simulated in glove-box.The solid-liquid separation was achieved by ultrafiltration.The plutonium radioactivity was meas-ured by low background liquid scintillation spectrometer.The results show that the domi-nant oxidation state of plutonium either in deionized water or Beishan groundwater is tetrava-lent.The solubility of Pu(Ⅳ)in Beishan groundwater and deionized water is (2.8±0.9)× 10-8 mol/L and (1.6 ±0.8)× 10 -9 mol/L.The specific ion interaction theory was used to calculate the thermodynamics constants under the experimental conditions.Either in deion-ized water or Beishan groundwater,the solubility-controlling solids phase is hydroxide pluto-nium (amorphous).In deionized water,the dominant species is hydroxide plutonium.In Beishan groundwater,the dominant species is hydroxide plutonium and Pu(OH)2 (CO3 )2 -2 .
A universal trapezoidation algorithm for planar polygons

B. Žalik,G. Clapworthy

DOI: https://doi.org/10.1016/S0097-8493(99)00044-8

IF: 1.821

1999-06-01

Computers & Graphics

Abstract:
Rapid Method To Determine 137 Cs, 237 Np, and Pu Isotopes in Seawater by SF-ICP-MS

Shuai Zhang,Zhiyong Liu,Guosheng Yang,Jian Zheng,Shaoming Pan,Tatsuo Aono,Aya Sakaguchi

DOI: https://doi.org/10.1021/acs.analchem.3c02702

IF: 7.4

2023-11-01

Analytical Chemistry

Abstract:Neptunium-237, owing to its long half-life (t(1/2) = 2.14 × 106 year) and similar conservatism to ^(137)Cs, has the potential to replace ^(137)Cs for water mass circulation studies on decades and even longer time scales. A new method for the determination of ^(137)Cs, ^(237)Np, and Pu isotopes in seawater samples was proposed to solve the difficulty of ^(237)Np analysis in seawater. The developed method includes the separation technique of ammonium phosphomolybdate (AMP) adsorption for ^(137)Cs...

chemistry, analytical
Ultra-trace Plutonium Determination in Small Volume Seawater by Sector Field Inductively Coupled Plasma Mass Spectrometry with Application to Fukushima Seawater Samples.

Wenting Bu,Jian Zheng,Qiuju Guo,Tatsuo Aono,Keiko Tagami,Shigeo Uchida,Hirofumi Tazoe,Masatoshi Yamada

DOI: https://doi.org/10.1016/j.chroma.2014.02.066

IF: 4.601

2014-01-01

Journal of Chromatography A

Abstract:Long-term monitoring of Pu isotopes in seawater is required for assessing Pu contamination in the marine environment from the Fukushima Dai-ichi Nuclear Power Plant accident. In this study, we established an accurate and precise analytical method based on anion-exchange chromatography and SF-ICP-MS. This method was able to determine Pu isotopes in seawater samples with small volumes (20-60L). The U decontamination factor was 3×10(7)-1×10(8), which provided sufficient removal of interfering U from the seawater samples. The estimated limits of detection for (239)Pu and (240)Pu were 0.11fgmL(-1) and 0.08fgmL(-1), respectively, which corresponded to 0.01mBqm(-3) for (239)Pu and 0.03mBqm(-3) for (240)Pu when a 20L volume of seawater was measured. We achieved good precision (2.9%) and accuracy (0.8%) for measurement of the (240)Pu/(239)Pu atom ratio in the standard Pu solution with a (239)Pu concentration of 11fgmL(-1) and (240)Pu concentration of 2.7fgmL(-1). Seawater reference materials were used for the method validation and both the (239+240)Pu activities and (240)Pu/(239)Pu atom ratios agreed well with the expected values. Surface and bottom seawater samples collected off Fukushima in the western North Pacific since March 2011 were analyzed. Our results suggested that there was no significant variation of the Pu distribution in seawater in the investigated areas compared to the distribution before the accident.
Rapid Method for Accurate Determination of Actinides (U, Th, Pu and Am) in Water Samples for Emergency Response

Zhongtang Wang,Jinxian Lin,Sixuan Li,Qiuju Guo,Wenna Huang,Wei Wen,Guiping Dan,Zhaoyi Tan

DOI: https://doi.org/10.1007/s10967-017-5640-0

2018-01-01

Journal of Radioanalytical and Nuclear Chemistry

Abstract:To rapidly assess the contamination of actinides in emergency water, a method was developed to simultaneously analyze U, Th, Pu and Am. The method consists of two steps: extraction chromatographic separation using UTEVA and DGA resins and isotopic determination of actinides by inductively coupled plasma mass spectrometry (ICPMS). The whole analytical procedure takes only 8 h and high chemical recoveries of actinides were obtained. The cross spectral interferences between actinides in ICPMS measurement were sufficiently removed. The accuracy was validated by analyzing IAEA-443 seawater sample. The low limits of detection of actinides allow this method to distinguish low level contamination.
Determination of Pu Isotopes in Sediment and Soil Samples by SF-ICP-MS: an Improved Anion-Exchange Procedure for Pu Separation

Wenting Bu,Jian Zheng,Qiuju Guo,Detao Xiao,Tatsuo Aono

DOI: https://doi.org/10.1007/s10967-017-5618-y

2017-01-01

Journal of Radioanalytical and Nuclear Chemistry

Abstract:An analytical method was established for the determination of plutonium isotopes in sediment and soil samples based on sector field ICP-MS and an improved anion-exchange procedure for Pu separation. A high U decontamination factor of 4 × 106 was obtained and the chemical yield of Pu was improved to be about 65%. The developed method was validated by the analysis of four soil and sediment reference materials, the analytical results agreed well with the certified and information values. We further applied this method to determine Pu isotopes in actual sediment and soil core samples for Pu source identification.
Comparisons of Soil Pretreatment Methods for SF-ICP-MS Determination of Ultra-Trace Level Plutonium in Water Soluble and Exchangeable Fractions

Youyi Ni,Jian Zheng,Qiuju Guo,Hai Wang,Keiko Tagami,Shigeo Uchida

DOI: https://doi.org/10.1007/s10967-018-5700-0

2018-01-01

Journal of Radioanalytical and Nuclear Chemistry

Abstract:In this study, we developed a method to evaluate the potentially bioavailable fraction of Pu in agricultural soils by determining their water soluble and exchangeable fractions. Three commonly used pretreatment methods were compared for their ability and performances to process the extracted solutions. Results showed that these three methods were able to obtain consistent Pu concentration results; however, based on the experimental performance factors, we considered that wet-ashing followed by Fe(OH) 3 co-precipitation was the best pretreatment method, with which high 242 Pu recoveries for the overall process were realized for the water soluble fraction (69.8%) and the exchangeable fraction (70.6%).
Determination of Np, Pu and Am in High Level Radioactive Waste with Extraction-Liquid Scintillation Counting

Dazhu Yang,Yongjun Zhu,Rongzhou Jiao

DOI: https://doi.org/10.1007/bf02037994

1994-01-01

Journal of Radioanalytical and Nuclear Chemistry

Abstract:A new method for the determination of transuranium elements, Np, Pu and Am with extraction-liquid scintillation counting has been studied systematically. Procedures for the separation of Pu and Am by HDEHP-TRPO extraction and for the separation of Np by TTA-TiOA extraction have been developed, by which the recovery of Np, Pu and Am is 97%, 99% and 99%, respectively, and the decontamination factors for the major fission products (90Sr,137Cs etc.) are 104–106. Pulse shape discrimination (PSD) technique has been introduced to liquid scintillation counting, by which the counting efficiency of α-activity is >99% and the rejection of β-counts is >99.95%. This new method, combining extraction and pulse shape discrimination with liquid scintillation technique, has been successfully applied to the assay of Np, Pu and Am in high level radioactive waste.
Rapid Method to Determine 137cs, 237np, and Pu Isotopes in Seawater by SF-ICP-MS.

Shuai Zhang,Zhiyong Liu,Guosheng Yang,Jian Zheng,Shaoming Pan,Tatsuo Aono,Aya Sakaguchi

DOI: https://doi.org/10.1021/acs.analchem.3c02702

IF: 7.4

2023-01-01

Analytical Chemistry

Abstract:Neptunium-237, owing to its long half-life (t(1/2) = 2.14 x 10(6) year) and similar conservatism to Cs-137, has the potential to replace Cs-137 for water mass circulation studies on decades and even longer time scales. A new method for the determination of Cs-137, Np-237, and Pu isotopes in seawater samples was proposed to solve the difficulty of Np-237 analysis in seawater. The developed method includes the separation technique of ammonium phosphomolybdate (AMP) adsorption for Cs-137 and anion exchange chromatography for Np-237 and Pu, a measurement technique of gamma spectrometry for Cs-137 and SF-ICP-MS for Np-237 and Pu isotopes. Pu-242 as a pseudo isotope dilution tracer for Np, the negligible chemical fractionation between Np-237 and Pu-242 of 1.02 +/- 0.06 (k = 2) was obtained by implementing sophisticated control of the redox system and chromatographic elution optimization. The analytical results for the International Atomic Energy Agency Certified Reference Materials (IAEA-443) agreed with the reference values, showing chemical yields of 65-88%, U decontamination factor above 10(6) level, and improved sample throughput (5 days for 12 samples). Meanwhile, the lower method detection limits (MDLs) of Np-237, Pu-239, and Pu-240 were 1.3 x 10(-3), 0.065, and 0.15 mu Bq L-1 for 15 L seawater, respectively. Results obtained by the developed method can be used to evaluate the impact on the marine ecological system of the planned marine discharge of Fukushima decontaminated wastewater. Working toward that purpose, we are the first to report the Np-237 activity concentration in Pacific Ocean seawater sampled near the station site, and we obtained the value of 0.122-0.154 mu Bq L-1.
Radioanalytical method for the separation of trace plutonium and neptunium from uranium

Zsuzsanna Macsik,Stephen P. LaMont,Joel R. Maassen,Will S. Fisher,Jeremy D. Inglis,Lisa A. Hudston,Matthew E. Sanborn,Kimberly A. Hinrichs,Ivis F. Chaple,Michael E. Fassbender,Robert E. Steiner

DOI: https://doi.org/10.1007/s10967-024-09360-6

2024-02-16

Journal of Radioanalytical and Nuclear Chemistry

Abstract:A radioanalytical method was developed for the determination of trace plutonium and neptunium in samples composed primarily of uranium. The procedure uses a neodymium oxalate co-precipitation and a two-column separation using ion exchange resin to achieve high uranium decontamination, high plutonium and neptunium separation factors and low impurity levels. The separation of the three actinides from each other relies on their oxidation–reduction chemistry. Various measurement techniques can be applied to determine plutonium and neptunium in the purified fractions: i.e., alpha spectrometry, and thermal ionization mass spectrometry. The method development, validation, and applications are discussed.

chemistry, inorganic & nuclear, analytical,nuclear science & technology

Rapid Determination of Plutonium in Water Samples Using Vacuum Box System Separation and Low Background Liquid Scintillation Counter Measurement

Determination of Plutonium Isotopes (238pu, 239pu, 240pu, 241pu) in Environmental Samples Using Radiochemical Separation Combined with Radiometric and Mass Spectrometric Measurements

Determination of Plutonium Isotopes (Pu-238, Pu-239, Pu-240, Pu-241) in Environmental Samples Using Radiochemical Separation Combined with Radiometric and Mass Spectrometric Measurements

Rapid and Simultaneous Determination of 238Pu, 239Pu, 240Pu, and 241Pu in Samples with High-Level Uranium Using ICP-MS/MS and Extraction Chromatography

Rapid Determination of Ultra-Trace Plutonium Isotopes (239pu, 240pu and 241pu) in Small-Volume Human Urine Bioassay Using Sector-Field Inductively Coupled Plasma Mass Spectrometry.

A Rapid Method for Quantification OF 242Pu in Urine Using Extraction Chromatography and ICP-MS

The DNA laboratory and neurological practice.

Rapid determination of plutonium isotopes in small samples using single anion exchange separation and ICP-MS/MS measurement in NH3–He mode for sediment dating

Rapid Method for Sequential Determination of Pu and Am in Soil and Sediment Samples by Sector-Field Inductively Coupled Plasma Mass Spectrometry

Simultaneous determination of femtogram levels of 237Np, 239Pu, and 240Pu in environmental solid samples using extraction chromatography and ICP-MS/MS

Plutonium determination in seawater by inductively coupled plasma mass spectrometry: A review

Solubility of Pu(IV)Under Simulated Geological Disposal Condition

A universal trapezoidation algorithm for planar polygons

Rapid Method To Determine 137 Cs, 237 Np, and Pu Isotopes in Seawater by SF-ICP-MS

Ultra-trace Plutonium Determination in Small Volume Seawater by Sector Field Inductively Coupled Plasma Mass Spectrometry with Application to Fukushima Seawater Samples.

Rapid Method for Accurate Determination of Actinides (U, Th, Pu and Am) in Water Samples for Emergency Response

Determination of Pu Isotopes in Sediment and Soil Samples by SF-ICP-MS: an Improved Anion-Exchange Procedure for Pu Separation

Comparisons of Soil Pretreatment Methods for SF-ICP-MS Determination of Ultra-Trace Level Plutonium in Water Soluble and Exchangeable Fractions

Determination of Np, Pu and Am in High Level Radioactive Waste with Extraction-Liquid Scintillation Counting

Rapid Method to Determine 137cs, 237np, and Pu Isotopes in Seawater by SF-ICP-MS.

Radioanalytical method for the separation of trace plutonium and neptunium from uranium