Amperometric Determination of NADH Based on a Poly-Ni(ii)–curcumin Composite Film Modified Glassy Carbon Electrode

Xiaoqian Ouyang,Yaping Ding,Xi Ba,Shuqing Gu

DOI: https://doi.org/10.1039/c4ay00884g

IF: 3.1

2014-01-01

Analytical Methods

Abstract:A poly-Ni(ii)–curcumin composite film modified electrode was prepared for amperometric detection of NADH with high sensitivity.

What problem does this paper attempt to address?

Electrochemical Determination of Dopamine Using a Carboxyl-functionalized Carbon Nanotube-Modified Carbon Paste Electrode Doped with Polymeric Ferric Sulfate

Ting Ni,Tengfei Wang,Lingling Xi

DOI: https://doi.org/10.1080/00032719.2016.1245316

2017-01-01

Analytical Letters

Abstract:A novel electrochemical device for the sensitive determination of dopamine was developed based on a carbon paste electrode with polymeric ferric sulfate doped in the carbon paste and a carboxyl-functionalized carbon nanotube thin film on the surface. The modified electrode was characterized by scanning electron microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. The conditions for the preparation of electrode were optimized. The carbon nanotubes were shown to be stable on the surface of carbon paste electrode. The novel electrochemical device provided excellent activity toward dopamine. Amperometry and differential pulse voltammetry were used for the determination of dopamine in pH 7.0 phosphate buffer with a long linear range from 0.8 to 261 mu M and a detection limit of 0.2 mu M. The modified electrode showed excellent repeatability, good stability, and satisfactory reproducibility, thus demonstrating potential for practical applications.
Electrocatalytic Oxidation of NADH at Graphene-Modified Electrodes Based on Electropolymerized Poly(thionine-Methylene Blue) Films from Nature Deep Eutectic Solvents

Minling Ding,Tongtong Hou,Huizhe Niu,Nan Zhang,Ping Guan,Xiaoling Hu

DOI: https://doi.org/10.1016/j.jelechem.2022.116602

IF: 4.598

2022-01-01

Journal of Electroanalytical Chemistry

Abstract:In this paper, a sensing platform for the electrocatalytic oxidation of nicotinamide adenine dinucleotide (NADH) was proposed. It was prepared by the electropolymerization of poly(thionine-methylene blue) (PTH-MB) in ternary nature deep eutectic solvent (NADES) on a glassy carbon electrode (GCE) that was mod-ified with electrochemically reduced graphene oxide (ERG). The modified electrode was denoted as PTH-MBNADES-ERG/GCE. Cyclic voltammetry (CV), chronocoulometry (CC), electrochemical impedance spec-troscopy (EIS), scanning electron microscope (SEM), Raman spectroscopy, and Ultra Violet-Visible Spectroscopy (UV-Vis) were used to characterize the preparation processes. The electrochemical performances of the electrode in NADH oxidation were studied via CV and current-time methods. The NADH oxidation over -potential was lower on PTH-MBNADES-ERG/GCE compared to that on GCE, ERG/GCE, and PTH-MBNADES/GCE. The PTH-MBNADES-ERG/GCE showed excellent electrocatalytic activity for NADH oxidation with a linear range of 0.51-3333.33 mu M (R2 = 0.9534) and a detection limit of 0.159 nM. The sensor was further tested for NADH determination in artificial urine samples, showing promising biomedical applications.
Electropolymerization of Toluidine Blue into Multilayer Carbon Nanotube and PDDA on Screen-printed Electrode for Sensitive Detection of NADH

FENG Cai-hong,GUO Yan-yan,GAO Qiang

DOI: https://doi.org/10.3969/j.issn.1004-4957.2010.01.014

2010-01-01

Abstract:An electrochemical sensing platform was developed for the amperometric detection of β-nicotinamide adenine dinucleotide(NADH) via electrooxidative polymerization of toluidine blue into a multiwalled carbon nanotubes(MWCNTs)/poly(diallyldimethylammonium chloride)(PDDA) multilayer constructed by electrostatic layer-by-layer assembled onto a screen-printed electrode.Electrochemical techniques and scanning electron microscopy(SEM) were used to demonstrate that the porous composite was formed on the surface of the electrode and carbon nanotubes served as nanosized backbone for loading the polymeric toluidine blue.Compared with the pure poly(toluidine blue) modified electrode,the sensitivity of the hybrid film modified electrode was improved for the determination of NADH.In phosphate buffer solution(pH=7.4),the electrocatalytic current for NADH oxidation was enhanced with the increase of the number of layers.The assembled amount on the electrode surface of the CNTs increased significantly,thus leading to the increase of effective electrode area and the increase of the loading amount of poly(toluidine blue) on the electrode surface.Compared with the bare electrode,the oxidation potential was reduced by 560 mV,and the sensitivity increased significantly.Under the optimal condition,a linear range of 8.7×10-8-1.3×10-4 mol/L NADH and a detection limit of 2.8×10-8 mol/L for NADH were obtained.Thus the(MWCNTs/PDDA)n-poly(toluidine blue) hybrid film on screen-printed electrode can be used for the detection of NADH.
Synthesis and Characterization of Novel Quinone‐Amine Polymer/Carbon Nanotubes Composite for Sensitive Electrocatalytic Detection of NADH

Xinman Tu,Qingji Xie,Zhao Huang,Qin Yang,Shouzhuo Yao

DOI: https://doi.org/10.1002/elan.200703939

IF: 3.077

2007-01-01

Electroanalysis

Abstract:A novel nanocomposite of quinone-amine polymer and multiwalled carbon nanotubes was synthesized from iodate-oxidation/Michael addition reaction of 1,2-dihydroxybenzene with o-phenylenediamine, which was characterized by TEM, FTIR and UV-vis spectra. The nanocomposite modified Au electrode with well-defined quinone redox peaks effectively mediated the oxidation of NADH in pH 7.0 phosphate buffer, with an overpotential decrease by ca. 470 mV (vs. bare An), a limit of detection of 6.4 nmol L-1 and good antiinterferent ability.
Amperometric Sensing of NADH and Ethanol Using a Hybrid Film Electrode Modified with Electrochemically Fabricated Zirconia Nanotubes and Poly (acid Fuchsin)

Xiaoqin Liu,Buhai Li,Ming Ma,Guoqing Zhan,Changxian Liu,Chunya Li

DOI: https://doi.org/10.1007/s00604-011-0701-5

IF: 5.7

2012-01-01

Microchimica Acta

Abstract:We report on a glassy carbon electrode (GCE) modified with a film of chitosin containing acid fuchsin (AF) adsorbed onto zirconia nanotubes. The mixture was polymerized by cyclic voltammetric scannings in the potential range from - 0.8 V to +1.3 V in buffer solution to produce a hybrid film electrode (nano-ZrO2/PAF/GCE). The morphology of the hybrid film electrode surface was characterized by scanning electron microscopy. Its electrochemical properties were studied via electrochemical impedance spectroscopy. The electrochemical response of nicotinamide adenine dinucleotide (NADH) was investigated by differential pulse voltammetry and amperometry. The results indicated that the nano-ZrO2/PAF/GCE possesses well synergistic catalytic activity towards NADH. Compared to an unmodified GCE, the oxidation overpotential is negatively shifted by 224 mV, and the oxidation current is significantly increased. Under optimal conditions, the amperometric response is linearly proportional to the concentration of NADH in the 1.0 – 100.0 μM concentration range. Ethanol also can be determined by amperometry if alcohol dehydrogenase and NADH are added to the sample. Two linear relationships between current and alcohol concentration were obtained. They cover the range from 0.03 to 1.0 mM, and from 1.0 to 12.0 mM.
A Nonenzymatic Electrochemical Glucose Sensor Based on Ni(Oh)(2)-Cnt-Pvdf Composite and Its Application in Measuring Serum Glucose

Yan Xing,Guangwei Gao,Guangming Zhu,Jihua Gao,Zaochuan Ge,Haipeng Yang

DOI: https://doi.org/10.1149/2.002406jes

IF: 3.9

2014-01-01

Journal of The Electrochemical Society

Abstract:A nano composite film was fabricated by dispersing nano scale Ni(OH)(2) and carbon nanotubes (CNTs) into polyvinylidene fluoride (PVDF). The mophorlogy of the film was examined by scanning electron microscopy (SEM). The electrocatalytic oxidation of glucose in alkaline medium on the Ni(OH)(2)-CNT-PVDF (NCP) composite modified glass carbon electrode had been investigated. The stability of the composite is confirmed by cyclic voltammetry measurements in sodium hydroxide solution (0.50 M, scan rate 100 mV s(-1)). The NCP composite film maintains the electrocatalytic activity of the nano scale Ni(OH)(2) and is used to fabricate a nonenzymatic biosensor for electrochemical detection of glucose. Amperometric measurements were done with different concentrations of glucose. The NCP glucose sensor has good anti-interference performance toward maltose, fructose, urea, and ascorbic acid. It has wide concentration ranges to glucose. It shows a detection limit of 0.023 mM (S/N = 3) with a wide linear range from 0.25 to 39.26 mM, which is comparable with commercial glucose test strip. In real serum sample, it has a RSD of 2.5%. (C) 2014 The Electrochemical Society. All rights reserved.
Indirect Electrochemical Detection of NADH Through an Active Stainless Steel Fiber Felt (SSFF) Electrode Decorated With the Amino-Graphene/Nafion Nano Composite Films

Wenqiong Su,Zonglin Li,Shuopeng Liu,Xianting Ding

DOI: https://doi.org/10.1002/slct.201800743

2018-01-01

ChemistrySelect

Abstract:As the energy transfer mediator in the metabolism of human beings, dihydronicotinamide adenine dinucleotide (NADH) is considered as an important biomarker, the concentration of which is correlated to several lethal diseases, such as breast cancer and Parkinson's disease. Due to the high oxidation potential encountered for NADH direct oxidation, herein, we report an active electrode for indirect electrochemical detection of NADH at low potential with the inexpensive stainless steel fiber felt (SSFF). The SSFF electrodes were modified through the layer-by-layer assembling of amino-graphene (AG) fragments and Nafion, and characterized by cyclic voltammetry (CV), differential pulse voltammetry (DPV), scanning electron microscope (SEM) and X-ray photoelectron spectroscopy (XPS). Taking the peak current at the apparent oxidation potential (-0.2V) as the sensing signal, the proposed SSFF active electrode presented a stable logarithmic detection range from 100 nM to 300M with R-2=0.996. The regeneration process was also explored and proved to be robust. Finally, the SSFF active electrode was applied to sense NADH in a bio-mixture solution prepared from tumor cell lysate. The experimental results demonstrated that, with a facile processing, the corrosion resistant and low cost SSFF electrodes could serve as a reliable and practical probe for NADH detection, which would further benefit the clinical diagnostics of NADH-related diseases.
Preparation of Chitosan–dopamine-Multiwalled Carbon Nanotubes Nanocomposite for Electrocatalytic Oxidation and Sensitive Electroanalysis of NADH

Bin Ge,Yueming Tan,Qingji Xie,Ming Ma,Shouzhuo Yao

DOI: https://doi.org/10.1016/j.snb.2009.01.030

2009-01-01

Abstract:A novel nanocomposite of glutaraldehyde crosslinked chitosan (CS)–dopamine (DA) composite with multiwalled carbon nanotubes (MWCNTs) was synthesized for low-potential and sensitive amperometric sensing of reduced nicotinamide adenine dinucleotide (NADH). The composite was characterized by FT-IR spectrophotometry. The nanocomposite modified Au electrode showed well-defined quinone/phenol redox peaks of the dopamine moieties and was able to effectively mediate the oxidation of NADH in pH 7.0 phosphate buffer, with an overpotential decrease by ca. 450mV (vs. bare Au). The NADH electrochemical sensor showed a linear range of 0.1–600μM, a limit of detection of 12nmolL−1, good antiinterferent ability, and long-term stability. It was also found that the use of acidified MWCNTs showed better performance than that of the nonacidified MWCNTs. Both CS and DA being biomaterials, the CS–DA/MWCNTs system should be of interest and potential for developing in vivo NAD+ (the oxidized form of NADH)-dependent dehydrogenase enzymes based biosensors.
Synthesis of polyaniline/Au composite nanotubes and their high performance in the detection of NADH

Xiaomiao Feng,Yu Zhang,Zhenzhen Yan,Yanwen Ma,Qingming Shen,Xingfen Liu,Quli Fan,Lianhui Wang,Wei Huang

DOI: https://doi.org/10.1007/s10008-014-2407-1

IF: 2.747

2014-01-01

Journal of Solid State Electrochemistry

Abstract:Polyaniline (PANI)/Au composite nanotubes were synthesized and developed as an electrode material for a nicotinamide adenine dinucleotide (NADH) sensor. A MnO 2 self-degradable template method was used to prepare the tube-like PANI nanomaterial. By introducing PANI nanotubes into Au colloid, Au nanoparticles (NPs) were successfully decorated onto the surface of PANI nanotubes through electrostatic effects. The morphology, composition, and optical properties of the resulting products were characterized by transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, ultraviolet-visible (UV-vis) absorption spectra, and thermogravimetric analysis (TGA). In addition, the obtained PANI/Au composites were used as catalysts for the electrochemical oxidation of NADH. Cyclic voltammogram (CV) experiments indicated that PANI/Au-modified glassy carbon electrode showed a higher electrocatalytic activity towards the oxidation of NADH in a neutral environment. Differential pulse voltammogram (DPV) results illustrated that the fabricated NADH sensor had excellent anti-interference ability and displayed a wide linear range from 4 × 10 −4 to 8 × 10 −3 M with a detection limit of 0.5 × 10 −7 M.
A glassy carbon electrode modified with poly(3,4-ethylenedioxythiophene) doped with nano-sized hydroxyapatite for amperometric determination of nitrite

Guixiang Wang,Rui Han,Xiuying Feng,Yinan Li,Jiehua Lin,Xiliang Luo,Guixiang Wang,Rui Han,Xiuying Feng,Yinan Li,Jiehua Lin,Xiliang Luo

DOI: https://doi.org/10.1007/s00604-017-2180-9

IF: 5.7

2017-03-18

Microchimica Acta

Abstract:A conducting polymer composite was prepared from nano-sized hydroxyaptite (nHAp) doped into poly(3,4-ethylenedioxythiophene) (PEDOT) and then electrodeposited on a glassy carbon electrode (GCE). The nHAp carries carboxy groups and therefore is negatively charged at moderate pH value. When doped into PEDOT (PEDOT-nHAp), it forms a uniform and stable film that exhibits low electrochemical impedance, a large specific surface, and high activity toward the electrochemical oxidation of nitrite. Under optimized conditions and at a relatively low working potential of 0.78 V (vs. SCE), the modified GCE exhibited a linear amperometric response in the 0.25 μM to 1.05 mM nitrite concentration range, and the limit of detection is as low as 83 nM.Graphical abstractA highly sensitive nitrite sensor was developed based on conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) doped with carboxyl group functionalized hydroxyapatite nanoparticles, which exhibited a large surface area and good conductivity and stability.

chemistry, analytical
Poly(phenosafranin)-functionalized Single-Walled Carbon Nanotube As Nanocomposite Electrocatalysts: Fabrication and Electrocatalysis for NADH Oxidation

Farhana S. Saleh,Takeyoshi Okajima,Fusao Kitamura,Lanqun Mao,Takeo Ohsaka

DOI: https://doi.org/10.1016/j.electacta.2011.02.011

IF: 6.6

2011-01-01

Electrochimica Acta

Abstract:We report a new type of amperometric dihydronicotinamide adenine dinucleotide (NADH) biosensor based on a poly(phenosafranin) functionalized single-walled carbon nanotube (PPS-SWCNT) nanocomposite. This nanocomposite, which was fabricated on an edge-plane pyrolytic graphite (EPPG) electrode surface, was formed by electropolymerizing a phenosafranin (PS) monomer onto SWCNTs. The PPS-SWCNT composites were characterized by surface analysis using atomic force microscopy (AFM), scanning electron microscopy (SEM) and UV-vis techniques and by electrochemical measurements using cyclic voltammetry (CV) and rotating disk electrode voltammetry (RDEV). Both the SEM and AFM studies revealed the successful immobilization of PPS on the SWCNT, whereas the UV-vis study suggested a strong charge-transfer interaction between them. The CV and RDEV results indicated that PPS-SWCNTs were able to mediate the oxidation of NADH effectively, with a remarkable decrease in overpotential by ca. 720 mV compared with the bare EPPG and with 10 times higher current than that at the PPS/EPPG electrode, (i.e., the catalytic reaction rate constant was estimated to be 3.36 x 10(5) M-1 s(-1)). This nanocomposite electrode was found to possess excellent characteristics as an amperometric NADH sensor including a low detection potential (0.0 V vs. Ag|AgCl|KCl(sat.)), rapid response (less than 2 s), low detection limit (10 nM), high sensitivity (576 mu A cm(-2) mM(-1)), high selectivity and reasonable stability. This new type of edge-plane-based electrochemical platform with a high surface area and catalytic activity offers great promise for creating a potentially alternative class of nanostructure electrodes for biosensing, biofuel cells and energy-conversion applications. (C) 2011 Elsevier Ltd. All rights reserved.
Selective Determination of Nicotinamide Adenine Dinucleotide (NADH) on Screen-Printed Polyethylene Terephthalate (PET) Electrodes Modified with a Reduced Graphene Oxide (rGO), Gold Nanoparticle (AuNP), and Poly-Methylene Blue Nanocomposite

Mallesh Santhosh,Tusan Park

DOI: https://doi.org/10.1080/00032719.2024.2356247

2024-06-04

Analytical Letters

Abstract:The present work reports the development of a disposable nanocomposite-based amperometric sensor for reduced nicotinamide adenine dinucleotide (NADH). To fabricate disposable electrodes, conductive carbon and silver ink were screen-printed on a polyethylene terephthalate (PET) film substrate. The surface of the working electrode was modified with gold nanoparticles (AuNPs) decorated reduced graphene oxide (rGO) and subsequently electro-polymerized with methylene blue for the determination of NADH. The nanocomposite modified electrode decreases the potential for NADH oxidation with a significant increase in the current due to the synergy between AuNP and rGO. The developed electrochemical sensor determined NADH at 0 V versus pseudo-Ag/AgCl with linear relationships from 25 μmol L −1 to 1.0 mmol L −1 and 1.0 mmol L −1 to 10 mmol L −1 . The sensor exhibits a good sensitivity of 35.49 μA/mmol L −1 /cm 2 and a detection limit of 6.61 μmol L −1 based upon a signal-to-noise ratio of 3. Furthermore, interferences from electroactive substances such as ascorbic acid and uric acid are eliminated at an oxidation potential of 0 V. Thus, the modified electrode provides a simple, selective, disposable, and low-cost approach for the amperometric determination of NADH.

chemistry, analytical
Highly Sensitive Sensor for Detection of NADH Based on Catalytic Growth of Au Nanoparticles on Glassy Carbon Electrode.

Lin Tang,Guangming Zeng,Guoli Shen,Yi Zhang,Yuanping Li,Changzheng Fan,Can Liu,Chenggang Niu

DOI: https://doi.org/10.1007/s00216-008-2560-4

2008-01-01

Analytical and Bioanalytical Chemistry

Abstract:In this work, an electrochemical dihydronicotinamide adenine dinucleotide (NADH) sensor based on the catalytic growth of Au nanoparticles (Au NPs) on glassy carbon electrode was developed. Catalyzed by Au NPs immobilized on pretreated glassy carbon electrode, the reduction of AuCl(4)(-) in the presence of hydroquinone and cetyltrimethyl ammonium chloride led to the formation of enlarged Au NPs on the electrode surface. Spectrophotometry and high-resolution scanning electronic microscope (SEM) analysis of the sensor morphologies before and after biocatalytic reaction revealed a diameter growth of the nanoparticles. The catalytic growth of Au NPs on electrode surface remarkably facilitated the electron transfer and improved the performance of the sensor. Under optimal conditions, NADH could be detected in the range from 1.25 x 10(-6) to 3.08 x 10(-4) M, and the detection limit was 2.5 x 10(-7) M. The advantages of the proposed sensor, such as high precision and sensitivity, fast response, low cost, and good storage stability, made it suitable for on-line detection of NADH in complex biological systems and contaminant degradation processes.
Electro-oxidative Polymerization of Phenothiazine Dyes into a Multilayer-Containing Carbon Nanotube on a Glassy Carbon Electrode for the Sensitive and Low-Potential Detection of NADH

Qiang Gao,Meng Sun,Ping Peng,Honglan Qi,Chengxiao Zhang

DOI: https://doi.org/10.1007/s00604-009-0283-7

IF: 5.7

2010-01-01

Microchimica Acta

Abstract:An electrochemical sensing platform was developed for the amperometric detection of β-nicotinamide adenine dinucleotide (NADH) through the integration of a multi-walled carbon nanotube (MWCNT) into electropolymerized phenothiazine dyes. The composite containing MWCNT and poly(phenothiazine) was prepared by electro-oxidative polymerization of phenothiazine derivatives, Azure B, Azure A and thionine, into an MWCNT/ poly(diallyldimethylammonium chloride) (PDDA) multilayer, which was constructed by electrostatic layer-by-layer assembly on a glassy carbon electrode. The three phenothiazine monomers used in this study exhibited similar electrochemical behaviors. Azure B was used extensively as a model monomer for the investigation. Electrochemical techniques and scanning electron microscopy were used to demonstrate that the porous composite was formed and that the carbon nanotube served as a nano-sized backbone for the loading of polymeric phenothiazine. The electrocatalytic current for NADH oxidation was enhanced as the number of layers increased, implying that the increase of NADH-accessible poly(phenothiazine) and the three-dimensional arrangement of the poly(phenothiazine)-coated MWCNT in the composite facilitated electron and NADH transfer. Under optimal conditions, the detection limit for NADH decreases to 7.0 × 10−8 M at a potential of 0.1 V (versus Ag/AgCl) using a {MWCNT/PDDA}8−poly(Azure B) composite modified glassy carbon electrode, with a response time of about 5 s. This work demonstrates that the electropolymerization of the phenothiazine monomer into a pre-formed multilayer containing MWCNT can be used for the controllable preparation of stable MWCNT/poly(phenothiazine) composites on electrode surfaces, which have the potential to provide a platform for electrochemical biosensors based on NAD+-dependent dehydrogenase enzymes.
Amperometric Sensing of Nitrite Using a Glassy Carbon Electrode Modified with a Multilayer Consisting of Carboxylated Nanocrystalline Cellulose and Poly(diallyldimethyl Ammonium) Ions in a PEDOT Host

Guiyun Xu,Shaoping Liang,Jinshi Fan,Ge Sheng,Xiliang Luo

DOI: https://doi.org/10.1007/s00604-016-1842-3

IF: 5.7

2016-01-01

Microchimica Acta

Abstract:Negatively charged carboxylated nanocrystalline cellulose (CNCC) and positively charged poly(diallyldimethyl ammonium chloride) (PDDA) were alternatingly assembled on the surface of a glassy carbon electrode to form a relatively uniform polyelectrolyte multilayer nanocomposite (CNCC/PDDA)n. It was then incorporated into a matrix of conducting poly(3,4-ethylenedioxythiophene) (PEDOT) electrodeposited on the surface of the electrode. The nanocomposites were prepared in various ratios of PEDOT and (CNCC/PDDA), and then characterized by transmission electron microscopy, scanning electron microscopy, electrochemical impedance spectroscopy, cyclic voltammetry, and differential pulse voltammetry. The PEDOT/(CNCC/PDDA)4 nanocomposite showed the lowest electrochemical impedance and best electrocatalytic activity towards the oxidation of nitrite. Based on these findings, an amperometric sensor was developed which, if operated at 0.80 V (vs. SCE), can detect nitrite in the 0.2 μM to 1.73 mM concentration range with a 57 nM detection limit.
Design of a Low Voltage TCNQ-Pd-Co@NC-Modified Electrode–Based NADH Sensor

Kuldeep Kumar Maurya,Kulveer Singh,Chitra Singh,Manisha Malviya

DOI: https://doi.org/10.1007/s12678-024-00865-y

2024-02-15

Electrocatalysis

Abstract:The present work involves the design and validation of an electrochemical sensor for precise and selective sensing of nicotinamide adenine dinucleotide (NADH). The designed electrochemical sensor consists of TCNQ and Pd-Co@NC nanocomposite–modified electrodes (TCNQ-Pd-Co@NC/CPE). The designed electrode was validated by cyclic voltammetry, amperometry, and electrochemical impedance spectroscopy (EIS). The results revealed potent electrocatalytic activity towards NADH oxidation and sensing. Cyclic voltammetry revealed the superior capability of TCNQ-Pd-Co@NC-based carbon paste electrode in electron transfer than TCNQ-Co@NC/CPE and TCNQ/CPE, validating better conductivity of TCNQ-Pd-Co@NC/CPE for NADH sensing. Amperometry study provided a wide linear range of 10 to 250 μM for NADH detection with a low detection limit (LOD) of 5.17 μM and a sensitivity of 21.5 μA mM. EIS study revealed the lowest R ct value of 12.5 × 10 2 for TCNQ-Pd-Co@NC/CPE compared to TCNQ-Co@NC/CPE and TCNQ/CPE, demonstrating high electron transfer capability and thus sensitivity towards NADH. Besides this, the modified TCNQ-Pd-Co@NC-based carbon paste electrodes offered exceptional selectivity, reproducibility, and stability over time. Therefore, designed TCNQ-Pd-Co@NC nanocomposite–based carbon paste electrodes can be efficiently used for precise and selective NADH sensing.

chemistry, physical,electrochemistry
Amperometric Biosensor for NADH and Ethanol Based on Electroreduced Graphene Oxide–polythionine Nanocomposite Film

Zou Li,Yi Huang,Li Chen,Xiaoli Qin,Zhao Huang,Yaping Zhou,Yue Meng,Jing Li,Siyu Huang,Yan Liu,Wen Wang,Qingji Xie,Shouzhuo Yao

DOI: https://doi.org/10.1016/j.snb.2013.01.072

2013-01-01

Abstract:A nanocomposite film is prepared by cyclic voltammetric deposition of electroreduced graphene oxide (ERGO) and polythionine (PTH) on a glassy carbon (GC) electrode. The electrodeposition of ERGO–PTH film is also investigated via the electrochemical quartz crystal microbalance (EQCM) method for more in-depth understanding of the process. The ERGO–PTH nanocomposite film is applied as transducer for facilitated electrocatalytic oxidation of NADH and for the construction of dehydrogenase-based amperometric biosensor. Under optimum conditions, the amperometric detection of NADH provides a wide linear detection range (0.01–3.9mM), a high sensitivity (143μAmM−1cm−2) and a low limit of detection (LOD=0.1μM, S/N=3). With alcohol dehydrogenase (ADH) as a model, we obtain a linear amperometric response of the ADH-modified ERGO–PTH/GC electrode to ethanol concentration from 0.05 to 1.0mM, a sensitivity of 2.8μAmM−1cm−2, and a LOD of 0.3μM (S/N=3).
A Novel Amperometric Nitric Oxide Sensor Based on Polythionine / Nation Modified Glassy Carbon Electrode

XX Chen,F Wang,YX Xu,SS Hu

2006-01-01

Abstract:A novel amperometric sensor for the determination of nitric oxide was developed by coating polythionine/nafion on a glassy carbon electrode. This sensor exhibited a great enhancement to the oxidation of nitric oxide. The oxidation peak currents were linear to the concentration of nitric oxide over the wide range from 3.6×10^(-7) to 6.8×10^(-5)mol.L^(-1), and the detection limit was 7.2×l0^(-8)mol.L^(-1). Experimental results showed that this nitric oxide sensor possessed excellent selectivity and longer stability. NO releasing from rat kidney was monitored by this sensor.
Amperometric Determination of Nitric Oxide at a Carbon Nanotube Modified Electrode with Redox Polymer Coating

Junjie Fei,Shengshui Hu,Kwok-Keung Shiu

DOI: https://doi.org/10.1007/s10008-010-1119-4

IF: 2.747

2010-01-01

Journal of Solid State Electrochemistry

Abstract:A novel chemically modified electrode based on an osmium complex-containing redox polymer film coated on single-walled carbon nanotube (SWNT) modified glassy carbon electrode (GCE) has been described for the determination of nitric oxide. The results showed that the oxidation current increased significantly at the SWNT/redox polymer coated GCE, as compared to that observed on a bare GCE- and SWNT-modified GCE. Amperometric measurement was carried out at the potential of +0.80 V (vs. Ag|AgCl) and the current response to NO was found to be directly proportional to its concentration in the range from 2.0 × 10−7 to 4.0 × 10−5 M, and the detection limit was estimated to be 5.0 × 10−8 M.
Preparation of Carbon-Nanotube/chitosan Modified Electrodes and Their Electrocatalysis for the Oxidation of NADH

DING Zhong-hua,KANG Tian-fang,HAO Yu-cui,ZHANG Yan

DOI: https://doi.org/10.3969/j.issn.1004-1656.2008.04.002

2008-01-01

Abstract:Muti-wall carbon nanotubes were activated in concentrated nitric acid.Chitosan and activated cabon-nanotube were prepared into composite material.A glassy carbon electrode was modified by pipetting a aliquot solution of the material onto the electrode surface to prepare electrocatalytic sensor of β-nicotinamide adenine dinucleotide(NADH).The electrochemical properties of the sensor and its electrocatalytic oxidation behaviours towards NADH were studied by cyclic voltammetry.Experimental results indicated that NADH produced an electrochemical oxidation peak at about +0.37V(vs.SCE).In comparison with a bared glassy carbon electrode,the oxidation peak potential of NADH at the modified electrodes proposed by this paper was substantially reduced.The problem of electrode fouling caused by reaction intermediate was eliminated.The experiment conditions were optimized and the determination method of NADH by differential pulse voltammetry using carbon-nanotubes/chitosan modified electrodes was established.The method proposed by this paper possess good reproducibility and selectivity.A linear response to NADH in the concentration range of 1.0×10-4~9.0×10-3 mol/L was observed,with a detection limit of 9.2×10-5 mol/L.

Amperometric Determination of NADH Based on a Poly-Ni(ii)–curcumin Composite Film Modified Glassy Carbon Electrode

Electrochemical Determination of Dopamine Using a Carboxyl-functionalized Carbon Nanotube-Modified Carbon Paste Electrode Doped with Polymeric Ferric Sulfate

Electrocatalytic Oxidation of NADH at Graphene-Modified Electrodes Based on Electropolymerized Poly(thionine-Methylene Blue) Films from Nature Deep Eutectic Solvents

Electropolymerization of Toluidine Blue into Multilayer Carbon Nanotube and PDDA on Screen-printed Electrode for Sensitive Detection of NADH

Synthesis and Characterization of Novel Quinone‐Amine Polymer/Carbon Nanotubes Composite for Sensitive Electrocatalytic Detection of NADH

Amperometric Sensing of NADH and Ethanol Using a Hybrid Film Electrode Modified with Electrochemically Fabricated Zirconia Nanotubes and Poly (acid Fuchsin)

A Nonenzymatic Electrochemical Glucose Sensor Based on Ni(Oh)(2)-Cnt-Pvdf Composite and Its Application in Measuring Serum Glucose

Indirect Electrochemical Detection of NADH Through an Active Stainless Steel Fiber Felt (SSFF) Electrode Decorated With the Amino-Graphene/Nafion Nano Composite Films

Preparation of Chitosan–dopamine-Multiwalled Carbon Nanotubes Nanocomposite for Electrocatalytic Oxidation and Sensitive Electroanalysis of NADH

Synthesis of polyaniline/Au composite nanotubes and their high performance in the detection of NADH

A glassy carbon electrode modified with poly(3,4-ethylenedioxythiophene) doped with nano-sized hydroxyapatite for amperometric determination of nitrite

Poly(phenosafranin)-functionalized Single-Walled Carbon Nanotube As Nanocomposite Electrocatalysts: Fabrication and Electrocatalysis for NADH Oxidation

Selective Determination of Nicotinamide Adenine Dinucleotide (NADH) on Screen-Printed Polyethylene Terephthalate (PET) Electrodes Modified with a Reduced Graphene Oxide (rGO), Gold Nanoparticle (AuNP), and Poly-Methylene Blue Nanocomposite

Highly Sensitive Sensor for Detection of NADH Based on Catalytic Growth of Au Nanoparticles on Glassy Carbon Electrode.

Electro-oxidative Polymerization of Phenothiazine Dyes into a Multilayer-Containing Carbon Nanotube on a Glassy Carbon Electrode for the Sensitive and Low-Potential Detection of NADH

Amperometric Sensing of Nitrite Using a Glassy Carbon Electrode Modified with a Multilayer Consisting of Carboxylated Nanocrystalline Cellulose and Poly(diallyldimethyl Ammonium) Ions in a PEDOT Host

Design of a Low Voltage TCNQ-Pd-Co@NC-Modified Electrode–Based NADH Sensor

Amperometric Biosensor for NADH and Ethanol Based on Electroreduced Graphene Oxide–polythionine Nanocomposite Film

A Novel Amperometric Nitric Oxide Sensor Based on Polythionine / Nation Modified Glassy Carbon Electrode

Amperometric Determination of Nitric Oxide at a Carbon Nanotube Modified Electrode with Redox Polymer Coating

Preparation of Carbon-Nanotube/chitosan Modified Electrodes and Their Electrocatalysis for the Oxidation of NADH