Abstract:The metallurgical properties of blast furnace slag changed when high alumina iron ore was used extensively due to the resulting changes of the molten slag microstructure. In the study, based on typical CaO–MgO–SiO2–Al2O3 slag systems with different w(Al2O3) content, molecular dynamics simulation was used to calculate the microstructural properties of particles in the high-temperature slag system, such as bond length, partial radial distribution function, coordination numbers, and diffusion coefficient. In addition, X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and 27Al solid-state magic angle spinning nuclear magnetic resonance (27Al SS MAS NMR) were used to detect and analyze the samples. The comprehensive calculations and experimental results show that increasing w(Al2O3) can enhance the structural stability of each ion pair, and the strength of the structural stability is such that Si–O > Al–O > Mg–O > Ca–O. The self-diffusion coefficients are as follows: Mg2+ > Ca2+ > Al3+ > Si4+, which leads to the transformation of the [SiO4]4−(Q0), [Si2O7]6−(Q1) and [Si2O6]4−(Q2) structural units to [Si2O5]2−(Q3). The degree of polymerization of slag increased as well as the stability of the structural units. Moreover, the coordination of Al will change from the [AlO6]9−octahedral structure of six-coordinated Al to the [AlO5]7−pentahedral structure of five-coordinated Al and the [AlO4]5−tetrahedral structure of four-coordinated Al. It was also found that the content of non-bridge oxygen in the whole slag system decreased continuously, leading to the increasing degree of polymerization of slag, and the experimental results were consistent with the molecular dynamics calculation.

Wetting Behavior of Al2o3 Substrate by Calcium Ferrite Series Melts

Wetting Behavior of Calcium Ferrite Melts on Sintered MgO

Wetting Behavior of Calcium Ferrite Slags on Cristobalite Substrates

Assimilation Behavior of Calcium Ferrite and Calcium Diferrite with Sintered Al2O3 and MgO

Wetting Behavior of TiO 2 by Calcium Ferrite Slag at 1523 K

Wetting and Spreading Behavior of Molten Iron in Contact with Graphite Substrate: Interfacial Effects

Effect of slag basicity on the interfacial wetting behavior between CA6 refractories and CaO–SiO2–MgO–Al2O3 based slag

Effect of Al2O3 on the Molten Slag Microstructure Information by Molecular Dynamics Simulation and Experimental Analysis

The Interface Characteristics of High-Temperature Melt of CaO-Al2O3-MgO-SiO2 System

Interactions between 3Al2O3·2SiO2, CA2, CA6, and Molten Slags

Wetting Behavior of CaO–SiO2- and CaO–Al2O3-Based Mold Slags on High-Ti Steel

Research on the Wetting and Corrosion Behavior Between Converter Slag with Different Alkalinity and MgO-C Refractories

Influence of Fluorine and CaO/Al2O3 Ratio on the Wetting Behavior Between CaO–Al2O3‐Based Mold Flux and Steel Substrate

Effect of Al2O3 on Sintering Reaction of Calcium Ferrite

Effects of TiO2 and CaO/Al2O3 on Melting Characteristics, Surface Tension, and Structure Electroslag‐Remelting‐Type Low‐Fluorine Slag

Effect of Alumina on Crystallization Behavior of Calcium Ferrite in Fe2O3-CaO-SiO2-Al2O3 System

A Comprehensive Investigation on the Sintering Behavior of CaO–SiO2–CaF2–Al2O3 Slags System

Influence of Grain Refiners on the Wettability of Al2O3 Substrate by Aluminum Melt

Wettability of Some Refractory Materials by Molten SiO2–MnO–TiO2–FeOx Slag

Wettability Between Molten Slag and Dolomitic Refractory

Effect of SiO2 and B2O3 on crystallization and structure of CaF2-CaO-Al2O3-based slag for electroslag remelting of ultra-supercritical rotor steel