Abstract:In view of the world-wide problem of energy sustainability and greenhouse gas production (carbon dioxide), it is timely to review the issues involved in generating heat and power from all fuels and especially new (to the UK) solid fuels, including high moisture fuels such as wood, SRF, oil shale, tar sands and brown coal, which will become major international fuels as oil and gas become depleted. The combustion properties of some of these materials are significantly different from traditional coal, oil and gas fuels, however the technology proposed herein is also applicable to these conventional fuels.This paper presents some innovative combustion system options and the associated technical factors that must be considered for their implementation. For clarity of understanding, the novel concepts will be largely presented in terms of a currently developing solid fuel market; biomass wood chips.One of the most important characteristics of many solid fuels to be used in the future (including oil shale and brown coal) is their high moisture content of up to 60%. This could be removed by utilising low grade waste heat that is widely available in industry to dry the fuel and thus reduce transport costs. Burning such dried wood for power generation also increases the energy available from combustion and thus acts as a thermal transformer by upgrading the low grade heat to heat available at combustion temperatures.The alternative approach presented here is to recover the latent heat by condensing the extrinsic moisture and the water formed during combustion. For atmospheric combustion, the temperature of the condensed combustion products is below the dew point at about 55-65 degrees C and is only suitable for recovery in an efficient district heating system. However, in order to generate power from the latent heat, the condensation temperature must be increased to the level where the heat can be used in the thermodynamic power cycle. This can be achieved by increasing the combustion pressure to above 80 bar, resulting in the recovered latent heat being available at more than 200 degrees C. It can then be used to increase the cycle efficiency by about 15% by pre-heating the boiler water and/or combustion air etc. A further advantage is that the high pressure of the combustion gases also reduces the superheater tube stress since it can balance the steam pressure.The key advantage of this high pressure flue gas is that it is above the pressure at which carbon dioxide 'condenses' to a liquid or supercritical gas at atmospheric temperature. Thus when used with oxy-fuel combustion, the carbon dioxide flue gas from which the moisture has been condensed can be cooled to atmospheric temperature and the supercritical CO2 can be fed directly into the pipes leading to the sequestration site. An important consideration of these strategies is to ensure that non-condensable gases in the exhaust, including oxygen and nitrogen, do not adversely affect the 'condensation' processes.When oxy-fuel combustion is used, the flame temperature must be moderated by a cool diluent. Recycled carbon dioxide is often proposed for this duty. However, since the latent heat is recovered, the moisture or even additional water can fulfil this role. This latter option may be advantageous since it is more efficient to pump wood chip fuel in water into the high pressure zone rather than feed solid wood particles. Surplus water can be simply drained and the wet wood chips are a good fuel when the latent heat of the moisture in the fuel gases is recovered into the power cycle.Bearing in mind that it is much more efficient to pump a liquid to high pressure than to compress the same material as a gas, indicates that cryogenic oxygen is a suitable material to use for an efficient power station that generates energy from biomass (or other fuels such as coal etc).Finally, combustion of the hydrogen from the water-gas reaction with oxygen allows the steam temperature in the turbine to be increased to the "gas-turbine engine" range of 1000-1400 degrees C and hence the biomass and/or fossil fuel cycle efficiency can be well over 60%! (C) 2010 Elsevier Ltd. All rights reserved.

Evaluation of a biomass drying process using waste heat from process industries: A case study

Experimental Performance Analysis of a Pilot-Scale Biomass-Assisted Recirculating Mixed-Flow Dryer for Drying Paddy

Performance analysis of a novel biomass-fired grain dryer integrated with thermal storage medium

Performance analysis of natural convection biomass operated grain dryer coupled with latent heat storage medium

Assessment of heat pump with carbon dioxide/low-global warming potential working fluid mixture for drying process: Energy and emissions saving potential

Wood Would Burn

Energy, exergy and economic analyses on heat pump drying of lignite

Evaluation of combined screening and drying steps for the improvement of the fuel quality of forest residue wood chips—results from six case studies

Integration of biomass drying with combustion/gasification technologies and minimization of emissions of organic compounds

Reducing energy requirement for drying of beet-pulp: Simulation of energy integration between superheated steam and air drying systems

Experimental and Theoretical Assessment of a Solar Assisted Heat Pump System for In-Bin Grain Drying: A Comprehensive Case Study

Multi-objective optimization and benefit evaluation of heat pump system for tobacco drying using waste heat from data center

EXPERIMENTAL RESEARCH ON THE PROCESS OF DRYING FUEL CHIPS FROM WOOD WASTE IN A FIXED BED

A Steam Dried Municipal Solid Waste Gasification and Melting Process

Thermodynamic and exergoeconomic assessment of a trigeneration system driven by a biomass energy source for power, cooling, and heating generation

Energy, exergy, exergoeconomic, and environmental analyses and multi-objective optimization of a biomass-to-energy integrated thermal power plant

Exergy analysis and optimisation of an industrial-scale circulation counter-flow paddy drying process

Thermo-economic-environmental analysis of a sustainable heat integration design for biomass-fueled power plant using integration of CCHP and sweater desalination application

Multi-objective Optimization, Comparison of Using Different Biomass Fuels in Hybrid Energy System for Electricity-Distilled Water Production Based on Supercritical CO2 and Humidification and Dehumidfication Cycles

Analysis of an Exhaust Heat Recovery Process of Integrating Bypass Flue and Condensate Air Heater for Efficient Power Generation

Energetic and financial assessment of the implementation of an absorption heat pump in an industrial drying system