Abstract:One of the important failure criteria of press operations in industry for forming simulations is the Forming Limit Diagram (FLD). The complex loading effects on FLD, in particular the localized necking phenomenon under stretch-bending condition, have not been fully investigated and well understood. In practical sheet metal applications, the deformation is invariably three dimensional with a combination of stretching and bending. For most sheet materials under these complex loading processes used in industry, strong Bauschinger effect is observed, and the material hardening behavior tends to be anisotropic. This study aims to understand and evaluate such anisotropic hardening effect on the forming limit prediction under stretch-bending condition. The extended through-thickness Marciniak–Kuczynski (M–K) analysis is incorporated with Yoshida–Uemori (YU) two-surface kinematic hardening constitutive model, which has a more accurate description of the reverse loading behavior than that of the conventional isotropic hardening model. The material parameters used in this paper for YU model are calibrated with the experimental data from uniaxial large-strain tension-compression cyclic test. Both the isotropic hardening and YU kinematic hardening models with Hill'48 yield surface are employed in the analysis for the purpose of comparison. The Forming Limit Average Stress Diagram (FLASD) under stretch-bending condition is proposed to extend the understanding of Forming Limit Stress Diagram (FLSD) from in-plane to out-of-plane deformations. The “bending-ratio-dependent” phenomenon in forming limit diagram is predicted and observed in both stress/strain space with the proposed method. It suggests that the individual stress/strain state cannot represent system behavior. Forming limits under stretch-bending is suggested as an occurrence of system instability, not individual material instability. The system behavior of sheet metal deformation is reinforced as critical to the understanding of necking instability in stretch bending processes. The analysis shows that the Bauschinger effect provides positive effect in delaying the necking instability, predicting higher formability for sheet metals under stretch-bending. The insight obtained in this paper provides further understanding of the localized necking phenomenon under stretch-bending condition.

Theoretical failure investigation for sheet metals under hybrid stretch-bending loadings

Sheet metal forming limits under stretch-bending with anisotropic hardening

Forming Limits of a Sheet Metal after Continuous-Bending-Under-Tension Loading

Application Of A New Semi-Empirical Model For Forming Limit Prediction Of Sheet Material Including Superposed Loads Of Bending And Shearing

Review on Fracture Criterion of Sheet Metal Forming

Analysis of Forming Limits Based on a New Ductile Damage Criterion in St14 Steel Sheets

Stamping Failure Analysis of Advanced High Strength Steel Sheet Based on Non-Uniform Local Deformation Through Thickness

Investigation of the Damage Behavior of Steel/CF Hybrid by Pure Bending Test

Forming Limits under Stretch-Bending Through Distortionless and Distortional Anisotropic Hardening

An Experimental and Theoretical Study on Constitutive Model of Al-2024T4 for Sheet Metal Incremental Forming

Prediction of Forming Limits for Anisotropic Materials with Nonlinear Strain Paths by an Instability Approach

M–K Analysis of Forming Limit Diagram under Stretch-Bending

Forming Limit of Sheet Metals Based on Mixed Hardening Model

Development of an Anisotropic Failure Criterion for Characterising the Influence of Curvature on Forming Limits of Aluminium Sheet Metal Alloys

A forming limit framework accounting for various failure mechanisms: localization, ductile and cleavage fracture

Evaluation of the Forming Limit of Incremental Sheet Forming Based on Ductile Damage

Experimental and Numerical Investigation on Sheet Metal Forming Limit Prediction with Thickness Related Criteria

Theoretical and experimental investigation progress on the forming limit of sheet metal forming

Numerical Investigations on the Influence of Superimposed Double-Sided Pressure on the Formability of Biaxially Stretched Aa6111-T4 Sheet Metal

Prediction of Strain Path Changing Effect on Forming Limits of AA 6111-T4 Based on a Shear Ductile Fracture Criterion

Forming limit of sheet metals in meso-scale plastic forming by using different failure criteria