Abstract:The rapid development of high-technology fields, such as aviation and aerospace engineering, leads to the increased demand for lightweight and high-strength bent tubes due to their desirable properties. However, these tubes are of clear anisotropy. The anisotropy of tubes is usually described in terms of the contractile strain ratio (CSR). The current method to determine CSR can only be applied to cases of small uniform plastic deformation. This makes it difficult to obtain the variation in CSR during the plastic forming processes in which large plastic deformation usually occurs. Considering that the circumferential strain and axial strain can be directly and continuously obtained using the Digital Speckle Correlation Method (DSCM), this study proposed a new method based on the DSCM for determining CSR values over a large deformation range. Using this method, small gage lengths can be flexibly adopted to obtain a uniform plastic deformation as large as possible. To improve the precision of the method, elastic deformation was compensated theoretically, and varied values of Young's modulus with deformation were adopted. Using this method, the CSR of Ti–3Al–2.5V (ASTM Gr. 9) titanium alloy seamless tubes, which are typical anisotropic tubes, was observed varying with plastic deformation in that it decreased rapidly in the initial stage, then decreased slowly until stabilizing in the final stage. The variation can be expressed approximately as a second-order decay equation. The results of this study also show that the variation of CSR is sensitive to the values of Young's modulus and Poisson's ratio, therefore, varied values of Young's modulus and reliable Poisson's ratio should be adopted to improve precision. By embedding the variation in CSR with deformation into the finite element (FE) simulation for the numerical control (NC) bending of Ti–3Al–2.5V seamless tubes, the predication accuracy for the thinning degree of wall thickness, the flattening degree of the cross-section, and the springback angle can all be improved.

A Constitutive Model for Anisotropic Tubes Incorporating the Variation of Contractile Strain Ratio with Deformation

Variation of Contractile Strain Ratio of Ti–3Al–2.5V Tubes and Its Effects in Tubes Numerical Control Bending Process

An Anisotropic Constitutive Model for Forming of Aluminum Tubes under Both Biaxial Tension and Pure Shear Stress States

Experimental and Numerical Study of the Superelastic Behaviour on NiTi Thin-Walled Tube under Biaxial Loading

An Accurate Determination Method for Constitutive Model of Anisotropic Tubular Materials with DIC-based Controlled Biaxial Tensile Test

Establishment of a 3D FE Model for the Bending of a Titanium Alloy Tube

Microstructure and Damage Based Constitutive Modelling of Hot Deformation of Titanium Alloys

Constitutive modeling based on non-associated flow rule for anisotropic sheet metals forming

Experimental Verification of Anisotropic Constitutive Models under Tension-Tension and Tension-Compression Stress States

Section Flattening in Numerical Control Bending Process of TA18 High Strength Tube

The Anisotropic Distortional Yield Surface Constitutive Model Based on the Chaboche Cyclic Plastic Model.

A Thermomechanically Coupled Finite Deformation Constitutive Model for Shape Memory Alloys Based on Hencky Strain

Quasi-Static Tensile Behavior and Constitutive Modeling of Large Diameter Thin-Walled Commercial Pure Titanium Tube

Constitutive Model of Hydroforming and Its Numerical Validation Based on Three-Dimensional Hill'48 Yield Criterion

Mechanical Modeling of Tube Bending Considering Elastoplastic Evolution of Tube Cross-Section

Predicting Plastic Behavior of Magnesium Alloy Tube Bending with Comprehensive Constitutive Models

Complex Stress-Strain Relations of Tubular Materials Studied with A Flexible Hydroforming System

Anisotropic and asymmetrical yielding and its evolution in plastic deformation: Titanium tubular materials

Elastoplastic Mechanical Properties and Kinematic Hardening Model of 35CrNi3MoVR

A Physically Based Elasto-Viscoplastic Constitutive Model for Modeling the Hot Deformation and Microstructure Evolution of a Near Α Ti Alloy

Tensile Deformation Behavior of High-Strength TA18 Titanium Alloy Tube under Warm Forming Conditions and Constitutive Model Based on Dislocation Density