Abstract:One of passive enhancement techniques, Extended Surfaces, are commonly employed in many heat exchangers to enlarge the heat transfer area on gases side because of the low heat transfer coefficients, which may be 10 to 100 times smaller than those of liquids side. The use of extended surfaces (or referred to as finned surfaces) will reduce the thermal resistance of gases side. Enhanced heat transfer coefficient will be achieved by using the basic surface geometries: plate-fin and tube-fin. With respect to the tube-fin type heat exchanger, fins may be employed outside tubes (herein called outer-fins) to enhance the heat transfer of shell-side, and alternatively fins may be also employed inside tubes (herein called inner-fins) to increase the intensity of heat transfer of tube-side. The desire to accomplish the gas-to-gas heat exchange through the tubular heat exchangers will lead to develop heat transfer enhancement techniques for outside and inside tubes. Therefore based on integration with such two mechanisms, namely, outer-fins and inner-fins of enhancement heat transfer techniques, a kind of outer-fins and inner-fins tube heat exchanger has been preliminary proposed (ASME-IGTI, Paper No.2006-90260 [20]). Such heat exchanger is potentially used in gas-to-gas heat exchangers, especially used for highpressure operating conditions, where the plate-fin heat exchangers might not be applicable. In general, the design task is a complex trial-and-error process and there is always the possibility that the design results such as geometrical parameters are not the optimum. Therefore, the motivation of this paper is to conduct optimum designs of such heat exchanger (hereafter called Outer-Fins and Inner-Fins tube Heat Exchanger, OFIF HE). A computational intelligent technique, Genetic Algorithm (GA) is applied to search and optimize geometrical parameters of the OFIF HE. The minimum total volume or minimum total annual cost of such OFIF HE is taken as an objective function in the GA respectively. The results show that the optimized OFIF HE provides lower total volume or lower total annual cost than those presented in previous work. The method is universal and may be used for design and optimization of OFIF HEs under different specified duties and design objectives.

Optimization of porous insert configurations for heat transfer enhancement in tubes based on genetic algorithm and CFD

Thermohydraulic Performance Optimization of Integrated Porous Pin Fins in Microchannel Heat Sink Using Shape Optimization Coupled with NSGA

Thermal Analysis of a Solar Parabolic Trough Receiver Tube with Porous Insert Optimized by Coupling Genetic Algorithm and CFD

Numerical configuration design and investigation of heat transfer enhancement in pipes filled with gradient porous materials

Optimization approach for tube circuit of fin-and-tube heat exchanger based on genetic algorithm

Intelligent optimization design of shell and helically coiled tube heat exchanger based on genetic algorithm

Optimizing Thermo-Hydraulic Performance in Heat Exchanger with Gradient and Multi-Layered Porous Foams

Performance analysis and multi-objective optimization for tubes partially filled with gradient porous media

Genetic Algorithm Based Design and Optimization of an Outer-Fins and Inner-Fins Tube Heat Exchanger

Net‐based thermal‐fluid model and hybrid optimization of cooling channels

Enhancing heat transfer efficiency in corrugated tube heat exchangers: A comprehensive approach through structural optimization and field synergy analysis

Geometrical Optimization Design of Plate-fin Heat Exchanger Using Genetic Algorithm

Knowledge Based Genetic-Simulated-annealing Method for Optimizing Tube Circuit of Fin-and-tube Heat Exchangers

Optimization Design of Tube-Shell Heat Exchanger Based on Genetic Algorithm

Optimization Investigation on Configuration Parameters of Serrated Fin in Plate-Fin Heat Exchanger Using Genetic Algorithm

Configuration Parameters Design and Optimization for Plate-Fin Heat Exchangers with Serrated Fin by Multi-Objective Genetic Algorithm

Multi-objective Optimization of Elliptical Tube Fin Heat Exchangers Based on Neural Networks and Genetic Algorithm

Optimization of heat transfer performance of a micro‐bare‐tube heat exchanger using a genetic algorithm

Experimental Investigation on the Thermal Performance of Multi-Stream Plate-Fin Heat Exchanger Based on Genetic Algorithm Layer Pattern Design

Numerical simulation and structural optimization of transpiration cooling with gradient porous matrix in supersonic condition

Thermal-Hydraulic Performance and Optimization of Tube Ellipticity in a Plate Fin-And-Tube Heat Exchanger