Abstract:Sc microalloying and isothermal multidirectional compression (IMC) are important methods to refine grains and improve the mechanical properties of Al–Zn–Mg–Cu–Zr alloys. Herein, EBSD , SAXS and TEM have been carried out to investigate the effect of IMC and minor Sc on the microstructure, especially for grain boundary wetting, and mechanical properties of aged Al–Zn–Mg–Cu–Zr alloys by melting and hot compression process parameter optimization. The results show that the strength and plasticity can be obviously improved simultaneously by minor Sc addition and IMC. Especially, stripy GBs (one kind of typical GB complexion) have been widely observed for alloy samples after microalloying Sc and IMC, which indicates the occurrence of GB wetting for Al–Zn–Mg–Cu–Zr alloy. And the GB wetting degree gradually increases for alloys with only microalloying Sc, only IMC and (microalloying Sc + IMC). Combined with GB wetting, the formation of Al 3 (Sc, Zr) due to Sc addition could inhibit the motion of dislocation and grain boundary, which promotes formation and inhibit growth of recrystallized grains, leading to further grain refinement. Besides, GB wetting degree would affect the precipitate distribution, especially for grain boundary precipitates. Also, GB wetting probably promote grain bridging, which is beneficial to improve the yield strength and ductility of Al–Zn–Mg–Cu–Zr alloys. The concurrent effect of grain refinement, the precipitate including finer Al 3 (Sc, Zr) particles, dislocation strengthening and grain bridging contribute to the simultaneous improvement of the strength and ductility of Al–Zn–Mg–Cu–Zr alloys under IMC and Sc. This study provides a new understanding on microalloying Sc combined with IMC on the microstructure and properties of Al–Zn–Mg–Cu–Zr alloys.

Influence of Alloyed Sc and Zr, and Heat Treatment on Microstructures and Stress Corrosion Cracking of Al–Zn–Mg–Cu Alloys

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Correlations Between Stress Corrosion Cracking Susceptibility and Grain Boundary Microstructures for an Al–Zn–Mg Alloy

In-situ electrochemical analytical effect of aging treatment on stress corrosion behavior of Al–Zn–Mg–Cu aluminum alloy

Correlations among stress corrosion cracking, grain-boundary microchemistry, and Zn content in high Zn-containing Al–Zn–Mg–Cu alloys

Correlation between stress corrosion cracking resistance and grain-boundary precipitates of a new generation high Zn-containing 7056 aluminum alloy by non-isothermal aging and re-aging heat treatment

Effect of aging on the mechanical properties and corrosion susceptibility of an Al-Cu-Li-Zr alloy containing Sc

Nanostructure Characteristics of Al3Sc1-xZrx Nanoparticles and Their Effects on Mechanical Property and SCC Behavior of Al-Zn-Mg Alloys

Microstructural evolution and mechanical properties of cast Al‐2.6Li‐2.8Mg‐(0.5, 1.4)Cu‐0.2Zr‐0.2Sc alloys during heat treatment

Influence of Sc and Zr additions on microstructure and properties evolution of Al–Zn–Mg alloy

Effect of isothermal multidirectional compression on microstructure and mechanical properties of Al–Zn–Mg–Cu–Zr alloy with minor Sc addition

Influence of Phase Dissolution and Hydrogen Absorption on the Stress Corrosion Cracking Behavior of Mg-7%Gd-5%Y-1%Nd-0.5%Zr Alloy in 3.5 Wt.% NaCl Solution

Enhancing properties of Al-Zn-Mg-Cu alloy through microalloying and heat treatment

Enhanced stress corrosion cracking resistance and electrical conductivity of a T761 treated Al-Zn-Mg-Cu alloy thin plate

SCC susceptibility of RRA treated high-zinc 7068 aluminum alloy

Sc/Zr microalloying on strength-corrosion performance synergy of wire-arc directed energy deposited Al-Mg

Effect of Overaging on Fatigue Crack Propagation and Stress Corrosion Cracking Behaviors of an Al-Zn-Mg-Cu Alloy Thick Plate

Corrosion behavior of Al-6.8Zn-2.2Mg-Sc-Zr alloy with high resistance to intergranular corrosion

Effect of Sc contents on the mechanical properties and damping capacity of Al-Zn-Mg-Cu-Zr-Sc alloys with different grain structures

Comprehensive improvement of stress corrosion cracking resistance and strength by retrogression and re-aging in Al-8.9Zn-2.6Mg-1.7Cu alloy

Effect of Quenching Rate on Microstructure, Mechanical and Corrosion Properties of Al-Zn-Mg-Cu-Cr-Zr Alloy