Abstract:Shell-and-tube heat exchangers are the most common type of heat exchangers in oil refineries and other large chemical processes. In this manuscript, we demonstrate that the shell-side flow in a cylindrical shell was not as homogeneous as that in a rectangular shell. According to the periodic flow field and the arrangement of tubes in the rectangular shell, the solid-fluid coupling heat transfer model consisting of a single tube section and the outer and inner fluids was developed to represent the whole heat exchanger. Using this model, the relationship among four temperatures, namely the inlet and outlet temperatures of tube-side fluid and the upstream and downstream temperatures of shell-side fluid, was established. By dividing each tube into several tube sections at the sites of baffles, a method for predicting the temperature field of the rectangular shell-and-tube heat exchanger was proposed. Based on the node temperature correlation, all the node temperatures were obtained by iterative computation using the established relationship between the four temperatures and the operating conditions. It was found that the temperature distribution of the fluid in tube was approximately linear along axial direction, but the temperature of tube showed nonlinear regularity. The axial deformation compatibility condition for the tube bundle and shell was considered when resolving the stresses in tubes. For the model established in this paper, the mean temperature of the tube at lower position was found to be larger than that at higher position; hence the thermal expansion of the tube at the lower end is larger. In the case the tube-side fluid was heated, all tubes were pulled because of the larger axial thermal expansion of shell, and the stress in the tube with higher temperature is smaller because of the smaller strain.

Prediction of Temperature Distribution in Shell-And-Tube Heat Exchangers

Numerical Study on Hydrodynamics, Mixing and Heat Transfer of Highly Viscous Fluid in a Novel Shell-and-tube Heat Exchanger with X-type Baffles

Temperature Field Prediction of Rectangular Shell-and-Tube Heat Exchanger

Numerical Modeling and Experimental Validation of Heat Transfer and Flow Resistance on the Shell Side of a Shell-and-tube Heat Exchanger with Flower Baffles

A comprehensive heat transfer prediction model for tubular moving bed heat exchangers using CFD-DEM: Validation and sensitivity analysis

Numerical Prediction and Analysis of the Dynamic Behavior of Heat Exchangers with Continuous Helical Shaped Baffles

A Study on the Thermal Performance of Heat Exchanger with Trefoil-baffles by Using Unit Duct Model

Numerical Simulation of Heat Transfer in Finned Tube of Heat Recovery Unit Using Fluid-Solid Coupled Method

Full Model Simulation of Shellside Thermal Augmentation of Small Heat Exchanger with Two Tube Passes

THREE-DIMENSIONAL NUMERICAL SIMULATION OF TURBULENT FLOW AND HEAT TRANSFER CHARACTERISTICS IN SHELL SIDE OF SHELL-AND -TUBE HEAT EXCHANGERS

NUMERICAL SIMULATION OF LAMINAR FLOW AND HEAT TRANSFER IN SHELL-AND-TUBE HEAT EXCHANGER WITH HELICAL BAFFLES

A New Heat Transfer Model for Single U-pipe Ground Heat Exchanger

A Numerical Study on the Shell-Side Turbulent Heat Transfer Enhancement of Shell-And-Tube Heat Exchanger with Trefoil-Hole Baffles

NUMERICAL INVESTIGATION ON HEAT STORAGE AND HEAT EXCHANGE OF THE SHELL-AND-TUBE PHASE CHANGE HEAT EXCHANGER

A thermal calculation model for tubular condensing heat exchanger

Experimental Study and Prediction of Pressure Drop and Heat Transfer in Shell-side of Tube-and-shell Heat Exchangers

3D Numerical Simulation on Shell-and-tube Heat Exchangers with Middle-Overlapped Helical Baffles and Continuous Baffles – Part I: Numerical Model and Results of Whole Heat Exchanger with Middle-Overlapped Helical Baffles

Numerical Simulation of Flow in Shell Side of Shell-and-Tube Heat Exchangers with Helical Baffles

A General Simulation Model for Performance Prediction of Plate Fin-and-tube Heat Exchanger with Complex Circuit Configuration

Prediction of Thermohydraulics in Shell Side of CAP1400 Steam Generator by Two-Fluid Porous Media Model

Numerical Simulation of the Heat Transfer Inside a Shell and Tube Heat Exchanger Considering Different Variations in the Geometric Parameters of the Design