Abstract:Utilization of low-grade heat has attracted considerable attention as an inspiring pathway towards sustainable and low-carbon energy future. However. low-grade heat, either in the form of natural source or waste heat, is abundantly available but not yet effectively exploited. With the outstanding merits of free maintenance and high reliability, thermoacoustic engine is conceived as one of cost-effective and reliable alternative technologies for low-grade heat recovery. Most recently, two-phase thermoacoustic engine induced increasing interest, thanks to its capability of running across a small temperature difference between heat source and heat sink. In this work. a vapor-liquid phase-change thermoacoustic engine, where the working fluid undergoes periodic condensation and evaporation, is constructed to realize low temperature-differential operation. The engine consists of a looped thermoacoustic unit and a branch resonator, where the former contains a cold heat exchanger. a regenerator. a hot heat exchanger and segments of tubes, while the latter contains a gas reservoir and a load tube. R134a is adopted as the working fluid in the preliminary study of this thermoacoustic engine, for its boling point near ambient temperature at the operating pressure around 0.5 MPa. Besides, R1234ze(E) is also used as the working fluid. thanks to its zero ozone depletion potential and low global warming potential. The experiments focus on onset temperature and pressure ratio, since the former determines the lowest grade of usable heat source, while the latter is an essential parameter for evaluating the intensity of pressure oscillation. The results show that an onset temperature of 18.1 degrees C. lowest ever reported, can be achieved with R134a as working fluid when the regenerator is packed with copper mesh screens. The highest pressure ratio of 1.094 is achieved with R1234ze(E) as working fluid at a hot temperature of 183 degrees C and a heating power of 200 W. which is comparable to the single-stage looped travelling wave thermoacoustic engine with helium of 1 MPa as working fluid at a similar hot temperature but a much lower heating power. Besides, the onset temperature firstly drops and then rises with the decreasing mesh number of regenerator's mesh screen, while the pressure ratio always rises. It is also found that regenerator material has marked effect on the engine performance. The engine with copper mesh screen achieves the lowest onset temperature, then stainless steel, and finally nylon. Besides, the cases of pressure ratio are in the increasing order of nylon_ stainless steel and copper. The low temperature-differential onset enables the phase-change thermoacoustic engine to harvest the near roomtemperature heat source. Further work on performance optimization of this novel thermoacoustic engine is still necessary and will be our near future work.

Optimization of a phase adjuster in a thermo-acoustic stirling engine using response surface methodology

Study on the onset and damping process of a thermoacoustic stirling prime mover

Study on the Performance of a Looped Thermoacoustic Prime Mover With Resistance Tube

Influence of Inner Diameter and Position of Phase Adjuster on the Performance of the Thermo-Acoustic Stirling Engine

Lumped Parameter Model for Resonant Frequency Estimation of a Thermoacoustic Engine with Gas-Liquid Coupling Oscillation

Impact of mean working pressure on performance of thermoacoustic engine with gas-liquid coupling oscillation

Application of Response Surface Methodology and Desirability Approach to Investigate and Optimize the Jet Pump in a Thermoacoustic Stirling Heat Engine

Theoretical and Experimental Investigation of Acoustic Field Adjustment of a Gas-Liquid Standing-Wave Thermoacoustic Engine

Multi-objective Thermodynamic Optimization of a Free Piston Stirling Engine Using Response Surface Methodology

Computation Of The Influence Of A Phase Adjuster On Thermo-Acoustic Stirling Heat Engine

Aerodynamic Shape Optimization of a Transonic Fan by an Adjoint-Response Surface Method

A Vapor-Liquid Phase-Change Thermoacoustic Engine Driven by Near Room-Temperature Heat Source

Optimizing design of a free piston Stirling engine using response surface methodology and grey relation analysis

Design Optimization with Computational Fluid Dynamic Analysis of Β-Type Stirling Engine

Simulation and Experimental Improvement on A Small-Scale Stirling Thermo-Acoustic Engine

Parametric Investigation of the Phase Characteristics of a Beta-Type Free Piston Stirling Engine Based on a Thermodynamic-Dynamic Coupled Model

Prediction and Parametric Analysis of Acoustic Streaming in a Thermoacoustic Stirling Heat Engine with a Jet Pump Using Response Surface Methodology

Phase Adjustment Analysis and Performance of a Looped Thermoacoustic Prime Mover with Compliance/resistance Tube

An Analytical Investigation of a Thermoacoustic stirling Engine

The Exergy Efficiency and Output Acoustic Power Performance Optimization of the Thermoacoustic Engine Micro-Cycle

Optimization Analysis of A Thermoacoustic Engine