Abstract:Free-form surface is a kind of complex, irregular, asymmetric aspherical surface. Generally, it can not be described with an equation, but usually by a series of digital points. Some special imaging effects can be realized by employing free-form lens. Moreover, because there is no constrain with free-form surface, the designer has more freedom of design by employing free-form lens in an optical system. However, it is quite difficult to fabricate free-form lens. This obstructs the wide application of free-form lens seriously.In this paper, a fabrication approach, named computer controlled fabrication (CCF), which includes: 1. computer numeric controlled (CNC) grinding, 2. CNC lapping, 3. profile measuring, 4. computer controlled corrective lapping, and 5. CNC polishing, is proposed. CNC grinding includes rough grinding, precision grinding, and fine grinding. Rough grinding is taken to remove the raw material rapidly. Precision grinding gets rid of the micro-crack layer and improves the profile accuracy. Fine grinding improves the figure accuracy further and generates very shallow micro-crack layer. After CNC grinding, a basic free- form surface with 'peak-valley' structure is obtained. CNC lapping is taken to get rid of the 'peak-valley' layer and micro-crack layer and to decrease the surface roughness without lowering the figure accuracy. Profile of the free-form lens is measured with a computer-controlled coordinate measuring machine. Machining error is obtained through the comparison between the measured data and theoretical profile data. Computer-controlled corrective lapping (CCCL) process provides the corrective NC code by full using the error data and unit removing profile, then corrective lapping is proceeded on a CCCL machine tool. Profile measuring and CCCL process are accomplished alternately until the required figure accuracy reached. Finally, the free-form lens is polished on a CNC polishing machine tool to lower the surface roughness.With CCF, two kinds of free-form glass lens were fabricated. Basic free-form glass lenses with figure error of +/-8 micron and surface roughness about Ra0.5 micron are obtained. After CNC lapping, surface roughness decreases to less than Ra0.05 micron. Profile accuracy is improved to about +/-2 micron after CCCL process, with surface roughness reaching Ra0.03 micron. After CNC polishing, free-form lens with profile accuracy of +/-3 micron and surface roughness less than Ra0.01 micron is obtained.

A theoretical and experimental investigation of design and slow tool servo machining of freeform progressive addition lenses (PALs) for optometric applications

Study on Optical Freeform Surface Manufacturing of Progressive Addition Lens Based on Fast Tool Servo

Optical Degradation Correction of Manufacturing-Perturbed Glass-Plastic Hybrid Lens Systems Via a Joint Hardware-Software Optimization Framework

Design of a Panoramic Annular Lens with a Long Focal Length.

Design of Vari-Focal Panoramic Annular Lenses Based on Alvarez Surfaces

Design of a Panoramic Annular Lens System with an Ultra-Wide Angle Via an Annular Gaussian Radial Basis Function Freeform Surface.

Design of a Panoramic Annular Lens with a Horizontal Symmetric FOV

A Framework of Cloud Supported Collaborative Design in Glass Lens Moulds Based on Aspheric Measurement

Improvement in Design of Panoramic Annular Lens Using Cemented Lenses

Surface Astigmatism Correction Using Segmented Freeform Surfaces for a Progressive Addition Lens.

A Framework of Cooperative Design for Aspheric Glass-Lens Mold

Design Of Freeform Lenses For Illuminating Hard-To-Reach Areas Through A Light-Guiding System

Experimental Study on Precision Molding of Small Dual Aspherical Chalcogenide Glass Lens

Freeform Liquid–Crystal Polarization Imaging Optics: A Practical Approach from Design to Fabrication

Optimization method for freeform progressive addition lenses using the coincident degree of weight distributions for power deviation and astigmatism

Design of a Compact Varifocal Panoramic System Based on the Mechanical Zoom Method.

A New Diamond Machining Approach for Extendable Fabrication of Micro-Freeform Lens Array

Establishment and analysis of feasibility evaluation system and ultra-precision manufacturing technology for small aperture free-form surface optical element

Design, fabrication and measurement of ultra-precision micro-structured freeform surfaces

Computer Controlled Fabrication of Free-Form Glass Lens

Design, analysis, and manufacturing of a glass-plastic hybrid minimalist aspheric panoramic annular lens