Abstract:Regarding the issue of intense mining pressure appearing in the underlying gateway below the remaining coal pillar in the close‐distance coal seam (the remaining coal pillar is perpendicular to the underlying section coal pillar), 401 working face is used as the engineering background. Field measurements, laboratory experiments, numerical simulations, and engineering verification techniques are used to study the abutment pressure's evolution properties and the plastic zone's propagation laws before and after the underlying coal seam roadway experienced the mining impact. The conclusions are as follows: 1 The maximum plastic area on the two sides and the roof of the roadway underlying the gob are up to 2 m and 1.5 m, whereas the maximum plastic area on the two sides and the roof of the roadway underlying the remaining coal pillar are up to 5 m and 4.5 m, respectively. Moreover, the plastic area extends along the two sides, and the section coal pillar is completely broken when the working face is mined below the remaining coal pillar. 2 The stress increase coefficient K in the overlap area of the remaining coal pillar and the underlying section coal pillar reaches 3.4 when the mining face penetrates the underlying remaining coal pillar and the advance abutment pressure is overlaid with the concentrated stress of the coal pillar. 3 When the underlying working face is mined to 4 m, ‐2 m, ‐8 m, and ‐14 m away from the remaining coal pillar, the damage range of the roadway 5‐10 m ahead increases in turn. At the same time, the maximum plastic area of the roof passes through the plastic area of the upper coal seam floor. Therefore, the underlying and transition areas on both sides of the remaining coal pillar are divided into Area I (15 m) → Area II (the most complicated area to control under the remaining coal pillar, 20 m) → Area III (25 m) according to the width. Furthermore, the divisional differentiated combined control technology of channel steel truss anchor cable with joint double‐way locking control function of roof and coal pillar in Area I and Area III, while channel steel truss anchor cable with joint double‐way locking control function of roof and side + high resistance integral door‐type support is proposed in Area II. Field engineering practice shows that the deformation of the roadway surrounding rock can be controlled within 210 mm after adopting the above divisional combined control technology. Finally, the mining operation can safely and efficiently pass through the remaining coal pillar. The research results have important reference values for surrounding rock control of mining roadways in the overlapping area of similar "+" type cross‐working face.This article is protected by copyright. All rights reserved.

Control Mechanism of Rock Burst in the Floor of Roadway Driven along Next Goaf in Thick Coal Seam with Large Obliquity Angle in Deep Well

Study on stress distribution law of surrounding rock of roadway under the goaf and mechanism of pressure relief and impact reduction

Mechanism and prevention of coal bursts in gob-side roadway floor under thick and hard roof in the deep mining area of Ordos

Mechanism and Control of Roadway Floor Rock Burst Induced by High Horizontal Stress

Research on the prevention and manage of rockburst in deep‐seam mining roadways

Study on hydraulic fracturing prevention and control of rock burst in roof of deep extra-thick coal seam roadway group

Analysis of Surrounding Rock Control Technology and Its Application on a Dynamic Pressure Roadway in a Thick Coal Seam

Study on rock burst characteristics of coal mine roadway in China

An effective control method of rock burst induced by shear instability of fault structure under complicated geological conditions

Stability control of goaf‐driven roadway surrounding rock under interchange remaining coal pillar in close distance coal seams

Dynamic Response Mechanism of Impact Instability Induced by Dynamic Load Disturbance to Surrounding Rock in High Static Loading Roadway

Research on the causal mechanism of a rock burst accident in a longwall roadway and its prevention measures

Floor Heave Mechanism and Control Technique of Water‐Rich Soft‐Rock Roadway in Thick Coal Seam

Stability Control of a Goaf-Side Roadway under the Mining Disturbance of an Adjacent Coal Working Face in an Underground Mine

Destabilization and energy characteristics of coal pillar in roadway driving along gob based on rockburst risk assessment

Mechanism and Control Technology of Rockburst Induced by Thick Hard Roof and Residual Coal Pillar: A Case Study

Failure mechanism and divisional differentiated control of surrounding rock in mining roadway under remaining coal pillar in close‐distance coal seam

Deformation and Failure Characteristics and Control Technology of Roadway Surrounding Rock in Deep Coal Mines

Non-uniform failure and differential pressure relief technology of roadway under irregular goafs in deep close-distance coal seams

Study on Failure Mechanism and Control Technology of Roadway Surrounding Rock under Complex Occurrence Coal Seam

Failure mechanism and stability control of surrounding rock in mining roadway with gentle slope and close distance