Solution-processed Bulk Heterojunction Solar Cells Based on a Porphyrin Small Molecule with 7% Power Conversion Efficiency

Hongmei Qin,Lisheng Li,Fangqing Guo,Shijian Su,Junbiao Peng,Yong Cao,Xiaobin Peng

DOI: https://doi.org/10.1039/c3ee43761b

IF: 32.5

2014-01-01

Energy & Environmental Science

Abstract:Solution-processed BHJ solar cells based on a porphyrin small molecule as the donor material exhibit a PCE of up to 7.23%.

What problem does this paper attempt to address?

Solution processed small molecule bulk heterojunction organic photovoltaics based on a conjugated donor-acceptor porphyrin

Yuying Huang,LiSheng Li,Xiaobin Peng,Junbiao Peng,Yong Cao

DOI: https://doi.org/10.1039/c2jm34429g

2012-01-01

Journal of Materials Chemistry

Abstract:Due to the pi-conjugation of the whole molecule along with the push-pull property of a newly designed conjugated donor-acceptor porphyrin, the solution processed solar cells using the blend of the porphyrin small molecule with PC71BM exhibit a promising performance with a power conversion efficiency of up to 4.02%.
Solution-processed Bulk Heterojunction Solar Cells Based on Porphyrin Small Molecules with Very Low Energy Losses Comparable to Perovskite Solar Cells and High Quantum Efficiencies

Ke Gao,Liangang Xiao,Yuanyuan Kan,Binglin Yang,Junbiao Peng,Yong Cao,Feng Liu,Thomas P. Russell,Xiaobin Peng

DOI: https://doi.org/10.1039/c5tc04011f

IF: 6.4

2016-01-01

Journal of Materials Chemistry C

Abstract:The BHJ OSCs presented in this work show an energy loss of 0.53 eV but a maximum external quantum efficiency up to 61%.
Enhanced Performance of Solution-Processed Solar Cells Based on Porphyrin Small Molecules with a Diketopyrrolopyrrole Acceptor Unit and a Pyridine Additive

Lisheng Li,Yuying Huang,Junbiao Peng,Yong Cao,Xiaobin Peng

DOI: https://doi.org/10.1039/c2ta00858k

IF: 11.9

2013-01-01

Journal of Materials Chemistry A

Abstract:A conjugated donor-acceptor porphyrin small molecule was designed and synthesized with diketopyrrolopyrrole as the acceptor unit. The new porphyrin-based small molecule exhibits broad and intense absorption in the visible and near IR regions, and the hole mobility and the power conversion efficiency of the bulk heterojunction devices based on the porphyrin : [ 6,6]-phenyl-C-61-butyric acid methyl ester (1 : 1, w/w) are increased up to 4.6 x 10(-5) cm(2) V-1 s(-1) and 3.71%, respectively, which are further enhanced to 1.6 x 10(-4) cm(2) V-1 s(-1) and 4.78%, respectively, upon the introduction of 3.0 vol% of pyridine additive. Further studies show that the performance of the solar cells based on other zinc porphyrins could also be improved by the pyridine additive.
Conjugated D-A Porphyrin Dimers for Solution-Processed Bulk-Heterojunction Organic Solar Cells.

Tianqi Lai,Xuebin Chen,Liangang Xiao,Lin Zhang,Tianxiang Liang,Xiaobin Peng,Yong Cao

DOI: https://doi.org/10.1039/c7cc00489c

IF: 4.9

2017-01-01

Chemical Communications

Abstract:Three conjugated D-A porphyrin dimers (DPP-ZnP-E)2, (DPP-ZnP-E)2-2T and (DPP-ZnP-E)2-Ph linked with diethynylene, diethynylene-dithiophene and diethynylene-phenylene have been developed for bulk heterojunction solar cells with high power conversion efficiencies of 4.50%, 5.50% and 6.42%, respectively, when blended with PC61BM as the electron acceptor material.
Structural Engineering of Porphyrin-Based Small Molecules As Donors for Efficient Organic Solar Cells.

Hongda Wang,Liangang Xiao,Lei Yan,Song Chen,Xunjin Zhu,Xiaobin Peng,Xingzhu Wang,Wai-Kwok Wong,Wai-Yeung Wong

DOI: https://doi.org/10.1039/c5sc04783h

IF: 8.4

2016-01-01

Chemical Science

Abstract:Porphyrin-based small molecules as donors have long been ignored in bulky heterojunction organic solar cells due to their unfavorable aggregation and the low charge mobility. With the aim of striking a delicate balance between molecular design, morphology, interfacial layer and device fabrication to maximize the power conversion efficiency (PCE) of organic solar cells, three comparable porphyrin-based small molecules with an acceptor-donor-acceptor configuration have been developed for use as donor materials in solution processed small molecule bulk heterojunction organic solar cells. In these molecules, electron-deficient 3-ethylrhodanine is introduced into the electron-rich porphyrin core through 5,15-bis(phenylethynyl) linkers. Structural engineering with 10,20-bis(2-hexylnonyl) aliphatic peripheral substituent on the porphyrin core, instead of the aromatic substituents such as 10,20-bis[3,5-di(dodecyloxyl)phenyl], and 10,20-bis(4-dodecyloxylphenyl), can simultaneously facilitate stronger intermolecular π-π stacking and higher charge transfer mobility in the film, leading to a maximum PCE of 7.70% in a conventional device. The inverted devices have also been demonstrated to have long-term ambient stability and a comparable PCE of 7.55%.
All-porphyrin Organic Solar Cells

Xiaojie Pan,Siyu Huang,Bei Zhu,Ruidong Xia,Xiaobin Peng

DOI: https://doi.org/10.1016/j.dyepig.2020.108503

IF: 5.122

2020-01-01

Dyes and Pigments

Abstract:Four small molecule electron acceptors TEH-PDI, TEH-DPDI, TPDI and TDPDI based on a porphyrin core and perylene bisimides (PDI) units were designed and synthesized. The energy levels and aggregation properties of the four acceptors were tuned to match those of a porphyrin electron donor C19OD-DPP based on a porphyrin core and 1,4-diketopyrrolo[3,4-c]pyrroles (DPP) end groups by adjusting the number of PDI units and the connection manners to a porphyrin core synergistically. The all-porphyrin bulk heterojunction (BHJ) solar cells exhibit panchromatic photon-to-current conversion from 300 to 900 nm with a small valley around 650 nm and provide power conversion efficiencies (PCEs) of 0.11%-2.57% when the active layers were prepared in the presence of octane-1,8-dithiol (ODT) additive. Further investigations show that more balanced hole/electron mobility, less trap-assisted monomolecular recombination and bimolecular recombination are beneficial for achieving higher J(SC) and PCE for C19OD-DPP/TPDI devices.
Solution-processed Small-Molecule Solar Cells: Breaking the 10% Power Conversion Efficiency

Yongsheng Liu,Chun-Chao Chen,Ziruo Hong,Jing Gao,Yang (Michael) Yang,Huanping Zhou,Letian Dou,Gang Li,Yang

DOI: https://doi.org/10.1038/srep03356

IF: 4.6

2013-01-01

Scientific Reports

Abstract:A two-dimensional conjugated small molecule (SMPV1) was designed and synthesized for high performance solution-processed organic solar cells. This study explores the photovoltaic properties of this molecule as a donor, with a fullerene derivative as an acceptor, using solution processing in single junction and double junction tandem solar cells. The single junction solar cells based on SMPV1 exhibited a certified power conversion efficiency of 8.02% under AM 1.5 G irradiation (100 mW cm−2). A homo-tandem solar cell based on SMPV1 was constructed with a novel interlayer (or tunnel junction) consisting of bilayer conjugated polyelectrolyte, demonstrating an unprecedented PCE of 10.1%. These results strongly suggest solution-processed small molecular materials are excellent candidates for organic solar cells.
Modifying the Chemical Structure of a Porphyrin Small Molecule with Benzothiophene Groups for the Reproducible Fabrication of High Performance Solar Cells.

Tianxiang Liang,Liangang Xiao,Ke Gao,Wenzhan Xu,Xiaobin Peng,Yong Cao

DOI: https://doi.org/10.1021/acsami.6b15241

IF: 9.5

2017-01-01

ACS Applied Materials & Interfaces

Abstract:A porphyrin-based molecule DPPEZnP-BzTBO with bulky benzothiophene groups was designed and synthesized as an electron donor material for bulk heterojunction (BHJ) solar cells. The optimized devices under thermal annealing (TA) and then chloroform solvent vapor anneanling (SVA) for 80 s exhibited an outstanding power conversion efficiencie (PCE) of 9.08%. Contrasted with the smaller thienyl substituted analogues we reported previously, DPPEZnP-BzTBO-based BHJ solar cells exhibited a higher open circuit voltage due to the lower highest occupied molecular orbital energy level. The TA post-treatment of the active layers induced the formation of more crystallized components, and the subsequent SVA provided a driving force for the domain growth, resulting in more obvious phase segregation between the donor and the acceptor in nanoscale. Furthermore, the PCEs kept above 95% upon the further SVA treatment within the time range of 60 to 95 s probably because the bulky benzothiophene groups retard the too quick change of crystallinity, providing a wide processing window for the reproducible device fabrication.
Solution‐Processed Small Molecules Using Different Electron Linkers for High‐Performance Solar Cells

Yongsheng Liu,Yang (Michael) Yang,Chun-Chao Chen,Qi Chen,Letian Dou,Ziruo Hong,Gang Li,Yang

DOI: https://doi.org/10.1002/adma.201301716

IF: 29.4

2013-01-01

Advanced Materials

Abstract:Conjugated acceptor-donor-acceptor small molecules using different electron linkers are designed, synthesized, and used in organic solar cells. All of these small molecules show high photoconversion efficiencies (PCEs), ranging from 3.18-6.15% under simulated AM 1.5G condition. A maximum PCE of 6.15% combined with a high Voc of 0.85 V, a Jsc of 10.79 mA cm(-2) and a notable FF of 67.1% are achieved with T3/PC71 BM blend based devices using polydimethylsiloxane as additive.
Panchromatic terthiophenyl-benzodithiophene conjugated porphyrin donor for efficient organic solar cells

Wei Tang,Liuping Xie,Zhixin Liu,Jie Zeng,Xuan Zhou,Pengqing Bi,Wencheng Tang,Lei Yan,Wai-Kwok Wong,Xunjin Zhu,Xiaotao Hao,Weiguo Zhu,Xingzhu Wang

DOI: https://doi.org/10.1039/d1tc01172c

IF: 6.4

2022-01-01

Journal of Materials Chemistry C

Abstract:A panchromatic terthiophenyl-benzodithiophene conjugated porphyrin donor for efficient organic solar cells exhibited an optimized PCE of 8.59%.

materials science, multidisciplinary,physics, applied
A Porphyrin-Fullerene Dyad with A Supramolecular "Double-Cable" Structure As A Novel Electron Acceptor for Bulk Heterojunction Polymer Solar Cells

Chien-Lung Wang,Wen-Bin Zhang,Ryan M. Van Horn,Yingfeng Tu,Xiong Gong,Stephen Z. D. Cheng,Yanming Sun,Minghong Tong,Junghwa Seo,Ben B. Y. Hsu,Alan J. Heeger

DOI: https://doi.org/10.1002/adma.201100399

IF: 29.4

2011-01-01

Advanced Materials

Abstract:With a supramolecular "double-cable" structure in the solid state, a light harvesting porphyrin-fullerene dyad is demonstrated to be a promising candidate for new electron acceptors in high-performance bulk heterojunction (BHJ) polymer solar cells (PSCs). It has long-lived mobile carriers, a high short circuit current, and a large open circuit voltage.
Non-Fullerene-Acceptor-Based Bulk-Heterojunction Organic Solar Cells with Efficiency over 7%

Dan Sun,Dong Meng,Yunhao Cai,Bingbing Fan,Yan Li,Wei Ji,Lijun Huo,Yanming Sun,Zhaohui Wang

DOI: https://doi.org/10.1021/jacs.5b06414

IF: 15

2015-01-01

Journal of the American Chemical Society

Abstract:A novel perylene bisimide (PBI) dimer-based acceptor material, SdiPBI-S, was developed. Conventional bulk-heterojunction (BHJ) solar cells based on SdiPBI-S and the wide-band-gap polymer PDBT-T1 show a high power conversion efficiency (PCE) of 7.16% with a high open-circuit voltage of 0.90 V, a high short-circuit current density of 11.98 mA/cm(2), and an impressive fill factor of 66.1%. Favorable phase separation and balanced carrier mobilites in the BHJ films account for the high photovoltaic performance. The results demonstrate that fine-tuning of PBI-based materials is a promising way to improve the PCEs of non-fullerene BHJ organic solar cells.
Solar Cells Sensitized by Porphyrin Dyes Containing a Substituted Carbazole Donor with Synergistically Extended Absorption and Suppressed the Dye Aggregation

Yunyu Tang,Xiujun Liu,Yueqiang Wang,Qingyun Liu,Xin Li,Chengjie Li,Xiaosheng Shen,Yongshu Xie

DOI: https://doi.org/10.1016/j.cclet.2019.12.038

IF: 9.1

2019-01-01

Chinese Chemical Letters

Abstract:To achieve high power conversion efficiency（PCE）,three porphyrin sensitizers have been synthesized and explored to simultaneously enhance the photocurrent(J SC ) and photovoltage(V OC ).On basis of the XW4,a benzothiadiazole（BTD） unit has been introduced to afford XW57 with the aim to extend the absorption wavelength and enhance the light harvesting ability.As a result,a J SC of 13.72 mA/cm~2 has been obtained for XW57,higher than that of XW4.On this basis,XW58 has been prepared by modifying the carbazole-based donor with two bulky dihexyloxyphenyl groups,and the superior anti-aggregation character raises the V OC from 781 mV（XW4） to 844 mV.When both the BTD unit and the bulky groups are introduced to the acceptor and donor units,respectively,the resulting sensitizer XW59 exhibits a highest PCE value of 7.34% with synergistically enhanced J SC of 13.19 mA/cm~2 and V OC of 793 mV.These results provide further insight into developing high performance dye-sensitized solar cells
Solution-Processed Squaraine Bulk Heterojunction Photovoltaic Cells

Guodan Wei,Siyi Wang,Kyle Renshaw,Mark E. Thompson,Stephen R. Forrest

DOI: https://doi.org/10.1021/nn100195j

IF: 17.1

2010-01-01

ACS Nano

Abstract:The donor, 2,4-bis[4-(N,N-diisobutylamino)-2,6-dihydroxyphenyl] squaraine (SQ) is used with the acceptor, [6,6]-phenyl C-70 butyric acid methyl ester (PC70BM) to result in efficient, solution-processed, small-molecule bulk heterojunction photovoltaic cells. The distribution of the donor nanoparticles in the acceptor matrix as a function of relative concentrations results in a trade-off between exciton dissociation and hole mobility (and hence, cell series resistance). A bulk heterojunction solar cell consisting of an active region with a component ratio of SQ to PC70BM of 1:6 has a power conversion efficiency of 2.7 +/- 0.1% with a 8.85 +/- 0.22 mA/cm(2) short-circuit current density and an open-circuit voltage of 0.89 +/- 0.01 V obtained under simulated 1 sun (100 mW/cm(2)) air mass 1.5 global (AM1.5 G) solar illumination. This is a decrease from 3.3 +/- 0.3% at 0.2 sun intensity, and is less than that of a control planar heterojunction SQ/C-60 cell with 4.1 +/- 0.2% at 1 sun, suggesting that the nanoparticle morphology introduces internal resistance into the solution-based thin film. The nanomorphology and hole mobility in the films is strongly dependent on the SQ-to-PC70BM ratio, increasing by greater than 2 orders of magnitude as the ratio increases from 28% to 100% SQ.
Integrated Perovskite/Bulk-Heterojunction toward Efficient Solar Cells

Yongsheng Liu,Ziruo Hong,Qi Chen,Weihsuan Chang,Huanping Zhou,Tze-Bin Song,Eric Young,Yang Yang,Jingbi You,Gang Li,Yang Yang,Yang (Michael) Yang

DOI: https://doi.org/10.1021/nl504168q

IF: 10.8

2014-12-18

Nano Letters

Abstract:We successfully demonstrated an integrated perovskite/bulk-heterojunction (BHJ) photovoltaic device for efficient light harvesting and energy conversion. Our device efficiently integrated two photovoltaic layers, namely a perovskite film and organic BHJ film, into the device. The device structure is ITO/TiO2/perovskite/BHJ/MoO3/Ag. A wide bandgap small molecule DOR3T-TBDT was used as donor in the BHJ film, and a power conversion efficiency (PCE) of 14.3% was achieved in the integrated device with a high short circuit current density (JSC) of 21.2 mA cm(-2). The higher JSC as compared to that of the traditional perovskite/HTL (hole transporting layer) device (19.3 mA cm(-2)) indicates that the BHJ film absorbs light and contributes to the current density of the device. Our result further suggests that the HTL in traditional perovskite solar cell, even with good light absorption capability, cannot contribute to the overall device photocurrent, unless this HTL becomes a BHJ layer (by adding electron transporting material like PC71BM).

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Porphyrin-Based Thick-Film Bulk-Heterojunction Solar Cells for Indoor Light Harvesting

Hang Yin,Song Chen,Sin Hang Cheung,Ho Wa Li,Yuemin Xie,Sai-Wing Tsang,Xunjin Zhu,S. K. So

DOI: https://doi.org/10.1039/c8tc02838a

IF: 6.4

2018-01-01

Journal of Materials Chemistry C

Abstract:A porphyrin-based donor material P1 is used to fabricate bulk-heterojunction solar cells harvesting room light. P1 consists of a porphyrin ring linked by two ethylrhodanine end caps via phenylene ethynylene bridges. Organic photovoltaic (OPV) cells using P1 as the donor exhibit significantly improved performances under indoor illumination compared to 1 sun conditions. For P1:PC71BM cells, an optimized-PCE of 19.2% was achieved under a 300 lux illumination of a 3000 K LED tube. Besides high PCEs, the porphyrin-based devices also exhibit enhanced OPV performances in thick film regions (approximate to 200 nm) compared to a control BHJ cell using PCDTBT:PC71BM. The thick-film P1-based device shows an overall PCE of 18.2%. The origins of the thickness independent OPV performances were examined, and they can be attributed to the low electronic disorders of these materials when compared to their polymer counterparts.
Porphyrins Containing a Tetraphenylethylene-Substituted Phenothiazine Donor for Fabricating Efficient Dye Sensitized Solar Cells with High Photovoltages

Jiazhi Zou,Yunyu Tang,Glib Baryshnikov,Zhen Yang,Rui Mao,Weifang Feng,Jian Guan,Chengjie Li,Yongshu Xie

DOI: https://doi.org/10.1039/d1ta09415g

IF: 11.9

2022-01-01

Journal of Materials Chemistry A

Abstract:Introduction of a dialkoxy-substituted tetraphenylethylene entity into porphyrin sensitizers improves the photovoltages and efficiencies of dye sensitized solar cells, affording a high power conversion efficiency of 12.3%.
Highly Efficient Small Molecule Solar Cells Fabricated with Non-Halogenated Solvents

Liangang Xiao,Chang Liu,Ke Gao,Yajing Yan,Junbiao Peng,Yong Cao,Xiaobin Peng

DOI: https://doi.org/10.1039/c5ra19054a

IF: 4.036

2015-01-01

RSC Advances

Abstract:Fabricated with non-halogenated solvents toluene and o-xylene, the bulk-heterojunction organic solar cells based on a porphyrin small molecule show high power conversion efficiencies up to 5.46% and 5.85%, respectively.
Highly Efficient Porphyrin‐Based OPV/Perovskite Hybrid Solar Cells with Extended Photoresponse and High Fill Factor

Ke Gao,Zonglong Zhu,Bo Xu,Sae Byeok Jo,Yuanyuan Kan,Xiaobin Peng,Alex K.‐Y. Jen

DOI: https://doi.org/10.1002/adma.201703980

IF: 29.4

2017-11-13

Advanced Materials

Abstract:Employing a layer of bulk-heterojunction (BHJ) organic semiconductors on top of perovskite to further extend its photoresponse is considered as a simple and promising way to enhance the efficiency of perovskite-based solar cells, instead of using tandem devices or near infrared (NIR)-absorbing Sn-containing perovskites. However, the progress made from this approach is quite limited because very few such hybrid solar cells can simultaneously show high short-circuit current (JSC ) and fill factor (FF). To find an appropriate NIR-absorbing BHJ is essential for highly efficient, organic, photovoltaics (OPV)/perovskite hybrid solar cells. The materials involved in the BHJ layer not only need to have broad photoresponse to increase JSC , but also possess suitable energy levels and high mobility to afford high VOC and FF. In this work, a new porphyrin is synthesized and blended with [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) to function as an efficient BHJ for OPV/perovskite hybrid solar cells. The extended photoresponse, well-matched energy levels, and high hole mobility from optimized BHJ morphology afford a very high power conversion efficiency (PCE) (19.02%) with high Voc , JSC , and FF achieved simultaneously. This is the highest value reported so far for such hybrid devices, which demonstrates the feasibility of further improving the efficiency of perovskite devices.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Chemically Driven Supramolecular Self-Assembly of Porphyrin Donors for High-Performance Organic Solar Cells

Xuan Zhou,Wei Tang,Pengqing Bi,Lei Yan,Xingzhu Wang,Wai-Kwok Wong,Xiaotao Hao,Beng S. Ong,Xunjin Zhu

DOI: https://doi.org/10.1039/c8ta04499f

IF: 11.9

2018-01-01

Journal of Materials Chemistry A

Abstract:Supramolecular self-assembly of a porphyrin donor with J-aggregates affords higher performance with a PC71BM acceptor in bulk heterojunction organic solar cells.

Solution-processed Bulk Heterojunction Solar Cells Based on a Porphyrin Small Molecule with 7% Power Conversion Efficiency

Solution processed small molecule bulk heterojunction organic photovoltaics based on a conjugated donor-acceptor porphyrin

Solution-processed Bulk Heterojunction Solar Cells Based on Porphyrin Small Molecules with Very Low Energy Losses Comparable to Perovskite Solar Cells and High Quantum Efficiencies

Enhanced Performance of Solution-Processed Solar Cells Based on Porphyrin Small Molecules with a Diketopyrrolopyrrole Acceptor Unit and a Pyridine Additive

Conjugated D-A Porphyrin Dimers for Solution-Processed Bulk-Heterojunction Organic Solar Cells.

Structural Engineering of Porphyrin-Based Small Molecules As Donors for Efficient Organic Solar Cells.

All-porphyrin Organic Solar Cells

Solution-processed Small-Molecule Solar Cells: Breaking the 10% Power Conversion Efficiency

Modifying the Chemical Structure of a Porphyrin Small Molecule with Benzothiophene Groups for the Reproducible Fabrication of High Performance Solar Cells.

Solution‐Processed Small Molecules Using Different Electron Linkers for High‐Performance Solar Cells

Panchromatic terthiophenyl-benzodithiophene conjugated porphyrin donor for efficient organic solar cells

A Porphyrin-Fullerene Dyad with A Supramolecular "Double-Cable" Structure As A Novel Electron Acceptor for Bulk Heterojunction Polymer Solar Cells

Non-Fullerene-Acceptor-Based Bulk-Heterojunction Organic Solar Cells with Efficiency over 7%

Solar Cells Sensitized by Porphyrin Dyes Containing a Substituted Carbazole Donor with Synergistically Extended Absorption and Suppressed the Dye Aggregation

Solution-Processed Squaraine Bulk Heterojunction Photovoltaic Cells

Integrated Perovskite/Bulk-Heterojunction toward Efficient Solar Cells

Porphyrin-Based Thick-Film Bulk-Heterojunction Solar Cells for Indoor Light Harvesting

Porphyrins Containing a Tetraphenylethylene-Substituted Phenothiazine Donor for Fabricating Efficient Dye Sensitized Solar Cells with High Photovoltages

Highly Efficient Small Molecule Solar Cells Fabricated with Non-Halogenated Solvents

Highly Efficient Porphyrin‐Based OPV/Perovskite Hybrid Solar Cells with Extended Photoresponse and High Fill Factor

Chemically Driven Supramolecular Self-Assembly of Porphyrin Donors for High-Performance Organic Solar Cells