Abstract:This study involved the fabrication of aluminum matrix composites reinforced with ZrB2/AA6016 particles using the KBF4-Al-K2ZrF6 reaction system, the composites were then subjected to T6 heat treatment. An investigation was conducted to examine the impact of varying friction speeds on the corrosion and wear characteristics of ZrB2/AA6016. An investigation was conducted to study the frictional wear behavior of ZrB2/AA6016 in the presence of 3.5wt. % NaCl, both before and after T6 heat treatment. The study also aimed to understand the underlying mechanism of this behavior. The results indicate that the T6 heat treatment mitigates the impact of thermal stresses and strains caused by thermal mismatch, hence enhancing the material's wear resistance. The coefficient of friction (COF) for heat-treated ZrB2/AA6016 is lower than that for unheated-treated ZrB2/AA6016. As friction increases, the pace at which the material wears down tends to decrease. At a friction wear velocity of 50 mm/s, the wear rate of the material is minimized both before and after heat treatment, measuring 0.23×10-2mm3/Nm and 0.22×10-2mm3/Nm, respectively. Through the utilization of XRD, SEM, EBSD, TEM, and XPS analytical techniques, it has been determined that the ZrB2 particles exhibit strong bonding with the Al matrix. Additionally, the particle diameters range from 50~150nm. Following the T6 heat treatment, the grain size measured 40.53μm, while the proportion of large-angle grain boundaries was found to be 66.4%. The accumulation of Cl- resulted in the formation of localized corrosion pits on the surface undergoing wear, hence hastening the deterioration of the material. The primary causes of wear failure are corrosive wear, abrasive wear, and oxidative wear.

Effect of Surface Roughness on Breakdown Behavior of Al-Zn-Mg-Cu Alloy

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Effect of Surface Roughness on Pitting Corrosion of AZ31 Mg Alloy

Microstructure and Corrosion Behavior of Ultrasonic Surface Treated 7B85 Al Alloy

Effect of Quenching Rate on Microstructure, Mechanical and Corrosion Properties of Al-Zn-Mg-Cu-Cr-Zr Alloy

Electrochemical corrosion behavior of 7075 aluminum alloy with different ultrasonic surface rolling microstructures

Influence of surface roughness of substrate on corrosion behavior of MAO coated ZM5 Mg alloy

Microstructure Evolution and Localized Corrosion Susceptibility of an Al-Zn-Mg-Cu-Zr 7xxx Alloy with Minor Cr Addition

Studies on Pitting Corrosion of Al-Cu-Li Alloys Part II: Breakdown Potential and Pit Initiation

Microstructure Evolution and the Resulted Influence on Localized Corrosion in Al-Zn-Mg-Cu Alloy during Non-Isothermal Ageing

Effect of Surface Roughness Induced by Milling Operation on the Corrosion Behavior of Magnesium Alloys

Microstructure and Properties of 7050-T74 Aluminum Alloys with Different Zn/Mg Ratios

Surface Roughening Behavior and Mechanism in Aluminum Alloy Under Tensile Deformation

In Situ Atomic Force Microscopy Observations of the Corrosion Behavior of Aluminum‐Copper Alloys

Experimental Investigation on Chemical Mechanical Polishing of ZA27 Alloy Considering Galvanic Corrosion at Zn/Al Interface

Microstructure Evolution of the Near-Surface Deformed Layer and Corrosion Behavior of Hot Rolled AA7050 Aluminum Alloy

Effect of Overaging on Fatigue Crack Propagation and Stress Corrosion Cracking Behaviors of an Al-Zn-Mg-Cu Alloy Thick Plate

Corrosion and wear performance and mechanism study of ZrB2/AA6016

Effect of grain size uniformity and crystallographic orientation on the corrosion behavior of Mg-2Zn-1Al bar

Enhanced Fatigue Crack Propagation Resistance in an Al-Zn-Mg-Cu Alloy by Retrogression and Reaging Treatment