Abstract:Using the shear-compression specimen (SCS), thermo-viscoplastic behavior of DP800 steel has been investigated systematically over a wide range of strain rates, including quasi-static (0.001-1 s(-1)), intermediate (10-100 s(-1)), high (2000-8000 s(-1)) and ultra-high (16,000-50,000 s(-1)) regions. Temperatures between 293 and 1073 K were considered. Experimental results show: (1) DP800 steel exhibits non-linear strain rate sensitivity. For tests at strain rates lower than 4000 s(-1), the flow stress increases slightly. However, for tests at strain rates above 8000 s(-1), a significant flow stress upturn exists; (2) dynamic strain aging (DSA) occurs within the temperature range of 473-873 K and strain rates below 100 s(-1); (3) both strain rate sensitivity and temperature sensitivity of DP800 steel are influenced by DSA, and bell-shaped sensitivity curves form; (4) with increasing strain rates, peaks of the bell-shaped temperature sensitivity curves move to higher temperature regions, and this law is equally valid for the effect of temperature on the strain rate sensitivity curves; (5) strain hardening behavior of DP800 steel is dominated by a competition between strain rate hardening, DSA hardening and thermal softening. With increasing strain rate, single peak or double peaks are observed in average strain hardening rate-strain rate curves. According to experiments, a semi-physical constitutive relation has been established, taking into account both the viscous drag effect and the DSA phenomenon. The established constitutive model can predict flow stress curves of DP800 steel accurately with an average error of 7.12%. Both the enhanced strain rate sensitivity due to viscous drag and the bell-shaped flow stress curves caused by DSA are captured correctly.

Effects of Strain Rates on Mechanical Properties and Fracture Mechanism of DP780 Dual Phase Steel

Mechanical behaviour of dual-phase high-strength steel under high strain rate tensile loading

Rate-Dependent Behavior And Constitutive Model Of Dp600 Steel At Strain Rate From 10(-4) To 10(3) S(-1)

Mechanical Behavior Of Dp980 High Strength Steel Under Dynamic Tensile Tests

Plastic Deformation Behavior and Construction of Constitutive Model in a Wide Range of Strain Rates of 800 MPa Grade Dual Phase Steel

Deformation Behaviors and Constitutive Model of DP1000 under Different Strain Rates

Rate-dependent behavior and constitutive model of DP600 steel at strain rate from 10−4 to 103s−1

Tensile Mechanical Behaviour of Ultra-High Strength Cold Rolled Dual Phase Steel DP1000 at High Strain Rates

Deformation Behavior and Microstructural Evolution in Ultra-High-strength Dual-Phase (UHS-DP1000) Steel with Different Strain Rates

Constitutive Model On The Description Of Plastic Behavior Of Dp600 Steel At Strain Rate From 10(-4) To 10(3) S(-1)

Constitutive model on the description of plastic behavior of DP600 steel at strain rate from 10−4 to 103s−1

Research on the Dynamic Deformation Behavior of the DP780 Advanced High Strength Steel

Constitutive model on the description of plastic behavior of DP600 steel at strain rate from 10−4 to 103 s−1

STUDY ON THE RATE-DEPENDENT EXPERIMENT AND CONSTITUTIVE MODEL OF HIGH STRENGTH STEEL DP600 BASED ON KHAN-HUANG MODEL

Thermo-viscoplastic Behavior of DP800 Steel at Quasi-Static, Intermediate, High and Ultra-High Strain Rates

Plastic Behavior and Constitutive Relations of DH-36 Steel over a Wide Spectrum of Strain Rates and Temperatures under Tension

Dynamic Hardening Behavior and Ductile Fracture of High-Strength Steel at Intermediate Strain Rates

A rate-dependent damage mechanics model for predicting plasticity and ductile fracture behavior of sheet metals at high strain rates

Strain-Hardening Behavior of Dual-Phase Steel under Multistress States

Effects Of Heterogeneous Microstructures On The Strain Hardening Behaviors Of Ferrite-Martensite Dual Phase Steel

Study Of The Mechanical Behavior Of Dual-Phase Steel Based On Crystal Plasticity Modeling Considering Strain Partitioning