Abstract:In the production process, people usually pay more attention to the parts' technical performance and production cost while ignoring the influence of the production process on workers' health and the environment. Therefore, in this paper, the multi-objective optimization for grinding process with AISI 1045 steel was conducted to obtain the optimal scheme of the workpiece feed velocities, the depths of cutting and cooling/lubrication conditions. The residual stress, surface roughness, production cost, production rate, operator health and CO2 emission were evaluated as optimization objectives. A series of models were proposed and revised to apply to the flood and small quantity cooling/lubrication grinding conditions. Grinding is a high specific energy processing method, and the grinding surface of the metal workpiece usually generates large tensile residual stress due to excessive grinding heat, which does harm to the surface quality and fatigue life of products. Therefore the residual stress and surface roughness were evaluated as the technical benefit by experiments. The production rate and production cost as the economic benefit, the harm of grinding fluid to machine tools operators as the healthy benefit, and the CO2 emission as the environmental benefit were considered based on models. An orthogonal experiment was designed by Taguchi method. The contribution rates of each objective and their corresponding sub-objectives were calculated by grey relational analysis to avoid the correlation effects among different objectives. Finally, the grinding schemes were optimized by the range analysis and validated by experiments and calculations. The results show that the combined technical, economic, healthy and environmental benefits were improved significantly with the optimal scheme of workpiece feed velocity 2.4 <math>mmin−1</math>, depth of cut 0.03 <math>mm</math>, and small quantity cooling/lubrication. It has an important reference value for green manufacturing. Besides, the feasibility of small quantity cooling/lubrication with water for the grinding process was proved.

Selection Of Optimal Process Parameters For Gear Hobbing Under Cold Air Minimum Quantity Lubrication Cutting Environment

Examination of Minimum Quantity Lubrication Performance in the Hard Turning of AISI/SAE 1060 High-Carbon Steel

High-speed machining parametric optimization of 15CDV6 HSLA steel under minimum quantity and flood lubrication

Experimental Optimization of Process Parameters for Turning TC11 Titanium Alloy Using Taguchi Methodology Design

Selection of Minimum Quantity Lubrication (MQL) Parameters in Milling of Ti-6Al-4V

Environmental, Economical and Technological Analysis of MQL-Assisted Machining of Al-Mg-Zr Alloy Using PCD Tool

Optimal Design of Parameters for the Nanofluid/Ultrasonic Atomization Minimal Quantity Lubrication in a Micromilling Process

Study on vibration and surface roughness in MQCL turning of stainless steel

Optimum parameters in milling GH4698 based on grey relational analysis

Assessment and optimization of grinding process on AISI 1045 steel in terms of green manufacturing using orthogonal experimental design and grey relational analysis

A Review of High-Speed Turning of AISI 4340 Steel with Minimum Quantity Lubrication (MQL)

Multi-verse optimizer based parameters decision with considering tool life in dry hobbing process

Optimization of Surface Quality and Power Consumption in Machining Hardened AISI 4340 Steel

Optimization of Cutting Parameters for Face Milling Titanium Alloy Using MQL

Sustainable Machining: MQL Technique Combined with the Vortex Tube Cooling When Turning Martensitic Stainless Steel X20Cr13

A Coupling Method of Response Surfaces (CRSM) for Cutting Parameters Optimization in Machining Titanium Alloy under Minimum Quantity Lubrication (MQL) Condition

Multi performance optimization in machining of EN31-535A99SS with interchangeable straight cemented tungsten carbide-cobalt mixed (WC–Co) insert grade (CSTC—K20) using Taguchi coupled grey relational analysis

The effects of minimum quantity lubrication parameters on the lubrication efficiency in the turning of plastic mold steel

Multi-objective optimization of hard milling process of AISI H13 in terms of productivity, quality, and cutting energy under nanofluid minimum quantity lubrication condition

Cryogenic minimum quantity lubrication machining: from mechanism to application

Minimum quantity lubrication machining of aeronautical materials using carbon group nanolubricant: From mechanisms to application