Porous MnFe2O4 Microrods As Advanced Anodes for Li-ion Batteries with Long Cycle Lifespan

Nana Wang,Xiaojian Ma,Yunpo Wang,Jian Yang,Yitai Qian

DOI: https://doi.org/10.1039/c5ta00828j

IF: 11.9

2015-01-01

Journal of Materials Chemistry A

Abstract:Porous MnFe2O4 microrods exhibit 630 mA h g−1 after 1000 cycles at 1 A g−1 and high coulombic efficiency (>98%).

What problem does this paper attempt to address?

A novel nanoporous Fe-doped lithium manganese phosphate material with superior long-term cycling stability for lithium-ion batteries

pengjian zuo,liguang wang,wei zhang,geping yin,yulin ma,chunyu du,xinqun cheng,yunzhi gao

DOI: https://doi.org/10.1039/c5nr01881a

IF: 6.7

2015-01-01

Nanoscale

Abstract:Here, we prepared LiMn0.8Fe0.2PO4 microspheres with an open three-dimensional nanoporous structure by a facile ion-exchange solvothermal method. The micro/nano-structured material exhibits an ultralong cycle life, and retains a reversible capacity of 105 mA h g(-1) after 1000 cycles at 5 C, corresponding to the capacity retention of 94.0% and only 0.0068 mA h g(-1) loss per cycle.
LiNi0.5Mn1.5O4 Microrod with Ultrahigh Mn3+ Content: A High Performance Cathode Material for Lithium Ion Battery

Lang Li,Jinsong Sui,Jian Chen,Yangcheng Lu

DOI: https://doi.org/10.1016/j.electacta.2019.03.086

IF: 6.6

2019-01-01

Electrochimica Acta

Abstract:In this work, we successfully use ultralong gamma-MnOOH microrods to synthesize ultralong spinel LiNi0.5Mn1.5O4 microrods through high temperature solid state reaction, which allows to drastically increase the content of residual Mn3+ ions (up to 61.3%) along with oxygen deficiency (up to 0.44) in spinel structure and improves the rate, cycling and discharge capacity of LiNi0.5Mn1.5O4 materials significantly. The excessive theoretical capacity (185 mAhg(-1)) is even observed at low charge and discharge rate due to the additional enhanced contribution of the Mn3+/Mn4+ redox couples. The LNMO-800 shows a little capacity decay with the increasing of the rate from 0.5 C to 1 C and 2 C, the discharge capacities were 145 mAhg(-1), 144.6 mAhg(-1) and 142 mAhg(-1), respectively. Even at a high rate of 10 C, it still deliveres a capacity of 125.3 mAhg(-1). After 1000 cycles at 1 C, the discharge capacity can still reach 120 mAhg(-1), corresponding to a capacity retention of 82.3%. The high temperature (55 degrees C) tests also demonstrate its excellent structural stability. The LiNi0.5Mn1.5O4 microrod with ultrahigh Mn3+ content should be a promising choice for future high energy power applications. (C) 2019 Elsevier Ltd. All rights reserved.
Porous ZnMn2O4 hollow microrods: Facile construction and excellent electrochemical performances for lithium ion batteries

Pu Zhou,Linping Zhong,Zhiyao Liu,Mengjiao Liu,Ting Zhou,Yan Zhao,Xin Lai,Jian Bi,Daojiang Gao

DOI: https://doi.org/10.1016/j.apsusc.2021.152087

IF: 6.7

2022-03-01

Applied Surface Science

Abstract:Porous ZnMn2O4 hollow microrods have been constructed through a facile co-precipitation method followed by an annealing process. The plausible formation mechanism for the unique architecture of ZnMn2O4 microrods was proposed and discussed in detail. It is found that the calcination temperature plays a key role in determining the microstructures of ZnMn2O4. On the whole, 700 °C is the optimal temperature, which not only makes the as-constructed ZnMn2O4 microrods (denoted as ZMO-700) the porous and hollow architecture, but also owns a good crystallinity, high porosity and large specific surface area. When used as anode materials for lithium ion batteries, the ZMO-700 exhibits outstanding electrochemical performances. It both possesses a high reversible capacity of 902 mAh g−1 after 320 cycles at 0.5 C, and presents an excellent rate capability in the current rate region of 0.1–5 C, especially deliveries a high capacity of 223 mAh g−1 at 5 C. The significant enhancement in the electrochemical performances should be attributed to the synergistic effect of the porous hollow architecture and the micro-nano hierarchical structure for the as-constructed ZnMn2O4 anode.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Electrospun LiMn1.5Ni0.5O4 Hollow Nanofibers As Advanced Cathodes for High Rate and Long Cycle Life Li-ion Batteries

Jian-Gan Wang,Huanyan Liu,Hongzhen Liu,Xu Li,Ding Nan,Feiyu Kang

DOI: https://doi.org/10.1016/j.jallcom.2017.09.112

IF: 6.2

2017-01-01

Journal of Alloys and Compounds

Abstract:High-voltage LiMn1.5Ni0.5O4 spinel with one-dimensional (1D) hollow and porous architecture is fabricated via a facile single-spinneret electrospinning technique. The hierarchical porous LiMn1.5Ni0.5O4 hollow nanofibers possess similar to 200 nm in diameter and tens of micrometers in length, as well as a specific surface area as high as 43.2 m(2) g(-1). When served as Li-ion battery cathodes, the as-fabricated material delivers high specific capacities of 135 and 98 mAh g(-1) at 0.68 C and 20.4 C, respectively. Under a long-term cycling operation at 6.8 C, the cathode sustains good capacity retention of 90% after 1000 cycles. The outstanding electrochemical performance can be attributed to the porous 1D hollow nanostructure that can enlarge effective electrode/electrolyte contact areas, shorten electron/ion transport distance and accommodate volume change. (C) 2017 Elsevier B.V. All rights reserved.
Superior lithium storage in Fe2O3 nanoporous arrays endowed by surface phosphorylation and bulk phosphorous doping

Jun Chen,Kun Wang,Minghao Sun,Wenbin Ni,Minjun Wang,Mincheng Yu,Dongxu Yu,Min Ling,Chengdu Liang

DOI: https://doi.org/10.1016/j.apsusc.2022.154668

IF: 6.7

2022-01-01

Applied Surface Science

Abstract:Fe2O3 film anodes are promising for application in lithium-ion micro-batteries in terms of their high theoretical capacity, earth-abundancy, and being environmentally friendly. Nevertheless, the low intrinsic electronic conductivity, sluggish Li+ diffusion, and unstable electrode-electrolyte interface stemming from cycling within Fe2O3 film limit its cyclic stability and rate capability. Herein, extraordinary cyclability and rate performance boosting of nanoporous Fe2O3 film anode are achieved using facile phosphorous heteroatom doping. The unique P-Fe2O3 nanoporous film can reversibly exhibit a capacity of 725 mAh/g at 248 mA g(-1) for 300 cycles with a capacity retention of 94.5 %, which is approximately 15 times higher than that without P doping. Moreover, the P-Fe2O3 nanoporous film can retain a capacity of 401 mAh/g at a high rate of 2.48 A/g and the initial coulombic efficiency can reach 90.4 %. Experimental results and density functional theory analysis verify that the enhanced performance derives from the synergistic effect of surface phosphorylation layer and bulk P doping defect, which can promote electron and Li+ transportation meanwhile enhancing surface faradaic redox sites. The insight from this work can provide a new avenue for the rational design of other advanced film electrodes through defect and surface engineering simultaneously.
Porous Α-Fe 2 O 3 Nanorods Supported on Carbon Nanotubes-Graphene Foam As Superior Anode for Lithium Ion Batteries

Minghua Chen,Jilei Liu,Dongliang Chao,Jin Wang,Jinghua Yin,Jianyi Lin,Hong Jin Fan,Ze Xiang Shen

DOI: https://doi.org/10.1016/j.nanoen.2014.08.011

IF: 17.6

2014-01-01

Nano Energy

Abstract:A novel flexible and lightweight Fe2O3-based lithium-ion battery anode has been developed by growing porous α-Fe2O3 nanorods onto carbon nanotubes–graphene foam (CNT–GF). The CNT–GF 3D network provides a highly conductive, high surface areas and lightweight scaffold for the active Fe2O3 nanorods. Such unique electrodes for lithium-ion battery exhibit an 80% initial columbic efficiency, high-rate capabilities, and >1000mAh/g capacities at 200mA/g up to 300 cycles without obvious fading. These properties can be attributed to the fast electrochemical reaction kinetics and electron transport rendered by the conductive 3D network. Our structural design protocol can be extended to many other nanostructured metal oxides or sulfides, and thus provides a new strategy for construction of high-performance electrodes for energy storage.
Intrinsic performance regulation in hierarchically porous Co3O4 microrods towards high-rate lithium ion battery anode

Yating Ma,Pengfei Liu,Qingshui Xie,Chenying Zhang,Laisen Wang,Dong-Liang Peng

DOI: https://doi.org/10.1016/j.mtener.2020.100383

IF: 9.257

2020-06-01

Materials Today Energy

Abstract:The hierarchically porous Co3O4 microrods made up of orientated self-assembled nanorods are fabricated through a facile strategy, which possess bicontinuous mesopores and one dimensional macropores. Oxygen vacancies are successfully introduced into Co3O4 microrods by simply controlling the heating temperature. When applied into lithium ion batteries as anode materials, local in-plane electric fields induced by the introduced oxygen vacancies and hierarchically bicontinuous porous feature endow Co3O4 microrods with enhanced ionic and electronic conductivity, outstanding structural stability and good electrochemical (de)lithiation reversibility. As a result, a high reversible capacity of 1858 mA h g−1 after 300 cycles at 0.5 A g−1 and distinguished high-rate long-term cycling stability with a specific capacity of 502 mA h g−1 after total 1000 cycles at 5 A g−1 are delivered. The magnetic hysteresis loops, zero-field cooled and field-cooled temperature-dependent magnetization curves after different cycles are used to explore the electrochemical reaction reversibility and structural stability of electrode materials. The result highlights the importance of the intrinsic performance regulation of atomic defects, morphology, microstructures and pores structure of anode materials on the improvement of their ionic and electronic conductivity, structural stability and thus electrochemical properties.

materials science, multidisciplinary,chemistry, physical,energy & fuels
Improved Electrochemical Performance of Porous Fe3o4/Carbon Core/Shell Nanorods As an Anode for Lithium-Ion Batteries

Q. Q. Xiong,Y. Lu,X. L. Wang,C. D. Gu,Y. Q. Qiao,J. P. Tu

DOI: https://doi.org/10.1016/j.jallcom.2012.05.034

IF: 6.2

2012-01-01

Journal of Alloys and Compounds

Abstract:Porous Fe3O4/C core/shell nanorods have been prepared by a facile hydrothermal method using porous Fe2O3 nanorods as the precursor and glucose as the carbon source. The Fe3O4/C nanorods possess a uniform size with 50–80nm in diameter and 300–500nm in length, and are homogenously coated by amorphous carbon layer. The porous nanorods greatly increase the electrical contact, thus facilitating the Li-ion and electron transportation, and enhancing the reactivity of the electrode. Also, the carbon layer can effectively limit the volume expansion and detachment of Fe3O4, and thus increase its structure stability during cycling. In the context of lithium storage behavior, the Fe3O4/C nanorod electrode shows high capacity and good cycle stability, as well as enhanced rate performance. After 50 cycles, the reversible capacity of the porous Fe3O4/C nanorods is 762.1mAhg−1 at 0.1C and 597.2mAhg−1 at 0.5C, much higher than that of α-Fe2O3 nanorods (276.4mAhg−1) and Fe3O4 nanoparticles (307.9mAhg−1). At a high rate of 1C, the specific capacity of Fe3O4/C nanorods is still as high as 630.1mAhg−1.
Superior Capacity, Rate, Long Cycle Life and High Temperature Performance of Multilayered Porous Ultralong LiMn2O4 Nanorods for Lithium Ion Batteries

Lang Li,Jinsong Sui,Wei Qin

DOI: https://doi.org/10.1016/j.jelechem.2018.09.039

IF: 4.598

2019-01-01

Journal of Electroanalytical Chemistry

Abstract:Multilayered porous ultralong LiMn2O4 nanorods with a length of 30 mu m, a diameter of 900 nm have been synthesized by using the ultralong gamma-MnOOH as a self-sacrifice template, which is involved in the dissolution, regrowth and self-assembly process. Galvanostatic charge and discharge measurements show that the multilDayered porous ultralong LiMn2O4 nanorods exhibit superior rate, specific capacity, long cycle stability and excellent high temperature performance. It delivers an initial charge and discharge specific capacity of 137.5 mAh g(-1) and 134 mAh g(-1) at 0.2C rate. Importantly, the multilayered porous ultralong nanorod structures are well preserved after prolonged charge and discharge cycling (1000 cycles) at a relatively high rate of 2C, 3C and 5C, demonstrating the excellent structural stability of the as-synthesized LiMn2O4, as is confirmed from scanning electron microscope images after several hundred cycles. Moreover, even at an extremely high rate of 50C, it still delivers a capacity of 75.4 mAh g(-1). The long cycle life, excellent high temperature and superior rate, and specific capacity performance are attributed to its ultralong and one-dimensional porous nanostructure, respectively.
Three-dimensional cross-linked MnO/Sb hybrid nanowires co-embedded nitrogen-doped carbon tubes as high-performance anode materials for lithium-ion batteries

Boya Wang,Yuting Xia,Zhiwen Deng,Yun Zhang,Hao Wu

DOI: https://doi.org/10.1016/j.jallcom.2020.155239

IF: 6.2

2020-09-01

Journal of Alloys and Compounds

Abstract:Developing high performance anode materials with fast reaction kinetics and cycling stability is a key for the next-generation lithium-ion batteries. Herein, a three-dimensional cross-linked porous MnO/ carbon tubes composite (MnO/) was designed and fabricated for lithium ions storage. In this composite, the MnO/Sb hybrid nanowires consisted of MnO and Sb nanoparticles were embedded in nitrogen-doped carbon tubes to construct coaxial porous composite nanowires, which were further assembled into a three-dimensional cross-linked network. This unique composition composed of both conversion-type MnO and alloying-type Sb makes the MnO/Sb nanowires possess high specific capacity and fast kinetics. Meanwhile, the advanced structure that collaboratively combines porous structure, exterior carbon tubes, one-dimensional morphology, and three-dimensional cross-linked network can greatly facilitate the rapid transfer of ions and electrons and ensure the structural integrity of the composite. As a result, the MnO/ demonstrated fast reaction kinetics and stable structure, therefore, presenting superior rate capability (217 and 150 mA h g−1 at 5 and 10 A g−1) and long cycling life (592 mA h g−1 after 1100 cycles at 1 A g−1). This unique design endows the MnO/ composite with a practical application potential and can be used to improve other conversion/alloying anode materials.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Carbon-coated MnFe2O4 nanoparticle hollow microspheres as high-performance anode for lithium-ion batteries

Yancui Yan,Guannan Guo,Tongtao Li,Dandan Han,Jiahui Zheng,Jianhua Hu,Dong Yang,Angang Dong

DOI: https://doi.org/10.1016/j.electacta.2017.06.020

IF: 6.6

2017-01-01

Electrochimica Acta

Abstract:In this work, carbon-coated MnFe2O4 nanoparticle (NP) hollow microspheres are fabricated by a facile emulsion-based assembly method followed by in situ ligand carbonization. Specifically, MnFe2O4 NPs stabilized by oleic acid (OA) are the primary building blocks to assemble hollow microspheres, while the subsequent carbonization of OA ligands leads to the formation of uniform carbon coatings without degrading the ordering of NPs. As anode materials for lithium-ion batteries, such MnFe2O4 NP hollow composite microspheres exhibit significantly improved electrochemical performance in comparison with their solid counterparts and most MnFe2O4-based anodes reported to date, retaining a high reversible capacity of 730mAhg−1 after 300 cycles at a current density of 2Ag−1. Furthermore, even when tested at an ultrahigh rate of 10Ag−1, MnFe2O4 NP hollow microspheres can still deliver a high specific capacity of 433mAhg−1. The superior performance of MnFe2O4 NP hollow microspheres is attributable to their hollow superstructure, close-packed configuration of the constituent NPs, and uniform carbon coatings, which facilitate lithium-ion and electron transport while simultaneously alleviating the drastic volumetric change during cycling. Our work establishes that the optimized MnFe2O4 anode material offers great promise for high-performance lithium-ion batteries.
Porous Carbon Nanofibers Encapsulated with Peapod-Like Hematite Nanoparticles for High-Rate and Long-Life Battery Anodes.

Guanglin Xia,Qili Gao,Dalin Sun,Xuebin Yu

DOI: https://doi.org/10.1002/smll.201701561

IF: 13.3

2017-01-01

Small

Abstract:Fe2 O3 is regarded as a promising anode material for lithium-ion batteries (LIBs) and sodium-ion batteries (SIBs) due to its high specific capacity. The large volume change during discharge and charge processes, however, induces significant cracking of the Fe2 O3 anodes, leading to rapid fading of the capacity. Herein, a novel peapod-like nanostructured material, consisting of Fe2 O3 nanoparticles homogeneously encapsulated in the hollow interior of N-doped porous carbon nanofibers, as a high-performance anode material is reported. The distinctive structure not only provides enough voids to accommodate the volume expansion of the pea-like Fe2 O3 nanoparticles but also offers a continuous conducting framework for electron transport and accessible nanoporous channels for fast diffusion and transport of Li/Na-ions. As a consequence, this peapod-like structure exhibits a stable discharge capacity of 1434 mAh g-1 (at 100 mA g-1 ) and 806 mAh g-1 (at 200 mA g-1 ) over 100 cycles as anode materials for LIBs and SIBs, respectively. More importantly, a stable capacity of 958 mAh g-1 after 1000 cycles and 396 mAh g-1 after 1500 cycles can be achieved for LIBs and SIBs, respectively, at a large current density of 2000 mA g-1 . This study provides a promising strategy for developing long-cycle-life LIBs and SIBs.
Pedot-Pss Coated Zno/C Hierarchical Porous Nanorods As Ultralong-Life Anode Material for Lithium Ion Batteries

Gui-Liang Xu,Yan Li,Tianyuan Ma,Yang Ren,Hsien-Hau Wang,Lifen Wang,Jianguo Wen,Dean Miller,Khalil Amine,Zonghai Chen

DOI: https://doi.org/10.1016/j.nanoen.2015.10.020

IF: 17.6

2015-01-01

Nano Energy

Abstract:ZnO/C hierarchical porous nanorods were synthesized through one-pot wet-chemical reaction followed by thermal calcination. It was found that ZnO/C porous nanorods are composed of numerous nanograins, exhibiting a hierarchical micro/nanostructure. In-situ synchrotron high energy X-ray diffraction study revealed that ZnO/C hierarchical porous nanorods involve a two-step reversible lithiation mechanism during charge/discharge; and part of ZnO and Zn remains at the end of the first discharge and charge process, respectively, leading to a low coulombic efficiency in the initial few cycles. The electrochemical test demonstrated that the reversible capacity and the rate performance of ZnO/C hierarchical porous nanorods anode have been greatly improved by PEDOT-PSS coating, which could maintain a reversible capacity of 623.94mAhg−1 after 1500 cycles at 1C. Its excellent high rate capability and long cycle stability were attributed to the high electronic conductivity of PEDOT-PSS coating layer and the hierarchical structures of ZnO/C porous nanorods.
The use of silastic transhepatic stents in benign and malignant biliary strictures.

J. Cameron,B. Gayler,G. Zuidema

DOI: https://doi.org/10.1097/00000658-197810000-00012

IF: 13.787

1978-10-01

Annals of Surgery

Abstract:Between 1969 and 1978, 45 patients with biliary strictures have been managed surgically utilizing silastic transhepatic stents. In 25 patients the strictures were benign. After resection or dilatation of the benign stricture, an hepaticojejunostomy was performed to a Roux-en-Y loop. The anastomosis was stented with a large bore silastic tube with multiple side holes passed through the biliary tree, out the anterior surface of the liver, and then out through the abdominal wall. There was one hospital death. Most stents were left in place for one year. Of the 15 patients with long-term follow-up, all have had excellent results. In 20 patients the strictures were malignant and involved the common hepatic duct in 10 patients or its bifuraction in 10 patients. In 14 patients the tumor was thought to be primary in the biliary tree, and in six patients the tumor was felt to represent a metastasis or direct extension from another site. In three patients the tumors were resected, and in the remaining they were dilated or bypassed. After positioning a silastic transhepatic stent, a hepaticojejunostomy was carried out. There were two hospital deaths. Serum bilirubin on admission average 17.1 mg%, and after decompression 1.8 mg%. Five patients have survived over one year, and two over two years. Postoperative radiotherapy and a primary biliary tumor favored longer survival.
Porous CoO/Co3O4 nanoribbons as a superior performance anode material for lithium-ion batteries

Xiao Li,Qian Chu,Mingqi Song,Chunhua Chen,Yulin Li,Xiaodong Tian,Yuming Cui,Deyang Zhao

DOI: https://doi.org/10.1016/j.apsusc.2023.156658

IF: 6.7

2023-05-01

Applied Surface Science

Abstract:The efficient and stable lithium-ion batteries have inspired extensive interest; however, formidable anode electrode materials still remain a challenge. Herein, porous CoO/Co3O4 nanoribbons were fabricated by a facile hydrothermal and annealing route. The self-assemble ultrathin CoO/Co3O4 nanoribbons are formed by connected nano-worms with mesoporous/macroporous structure and oxygen vacancy. The porous ultrathin CoO/Co3O4 nanoribbons benefit from buffering the volume change and enlarging the contact area between electrode and electrolyte, leading to long cycling life and high specific capacity. Furthermore, oxygen vacancies and a three-dimensional network enhance the internal conductivity and accelerate the diffusion of electrons/ions, resulting in excellent rate performance. The highest discharge capacity (957 mAh/g after 200 cycles at 0.5 A/g) and excellent rate capability (847 mAh/g at 5 A/g) are observed. Thus, these unique characteristics pave the way for CoO/Co3O4 nanoribbons as suitable electrode materials for lithium storage devices.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Controlled synthesis of α-FeOOH nanorods and their transformation to mesoporous α-Fe2O3, Fe3O4@C nanorods as anodes for lithium ion batteries

Jin Wang,Linlin Li,Chui Ling Wong,Linfeng Sun,Zexiang Shen,Srinivasan Madhavi

DOI: https://doi.org/10.1039/c3ra41886c

IF: 4.036

2013-01-01

RSC Advances

Abstract:α-FeOOH nanorods with varying lengths of 200–500 nm and axis ratios of 2–8 have been successfully synthesized by a simple hydrothermal method with different amounts of hydrazine. Hierarchical nanostructured mesoporous α-Fe2O3 and Fe3O4@C, which combined both mesoporosity and carbon coating, were fabricated by transformation of these α-FeOOH nanorods. The mechanism of formation has been described in detail. The α-FeOOH, mesoporous α-Fe2O3 and Fe3O4@C samples with the longest nanorods exhibited excellent cycle and rate performance, as the long nanorods could ensure many fast and convenient electron transport pathways, thus enhancing the electronic conductivity. The as-synthesized mesoporous α-Fe2O3 and Fe3O4@C nanorods showed large specific surface area and porosity due to the inner mesoporous structure, effectively increasing the contact area between the electrode materials and electrolyte, shortening the diffusion length of Li+ and alleviating the stress from volume changes during the charge–discharge process. Mesoporous Fe3O4@C nanorods exhibit high reversible capacities of 1072 mAh g−1 after 50 cycles, demonstrating the superior electron transport and fast Li+ diffusion ability combination of outer carbon layer and mesoporous microstructure.

chemistry, multidisciplinary
Hierarchical Mn3O4 Microplates Composed of Stacking Porous Nanosheets for High-Performance Lithium Storage

Ma Fei-Xiang,Wu Hao Bin,Sun Xue-Yin,Wang Pan-Pan,Zhen Liang,Xu Cheng-Yan

DOI: https://doi.org/10.1002/celc.201700323

IF: 4

2017-01-01

ChemElectroChem

Abstract:Transition metal oxide based anodes with high capacities and long cycle lifetimes are considered promising candidates to substitute the conventional graphite electrodes with a relatively low capacity. In this work, hierarchical Mn3O4 microplates with a lateral size of approximately 4.9 mu m, composed of stacking porous nanosheets with thicknesses as small as 10nm, were synthesized by using a precursor conversion method. Such a nanosheet stacking arrangement possesses an unusual concave structure with a tight center and loose edge. Owing to the highly open hierarchical structure and good electronic conductivity from the insitu carbon, the as-obtained hierarchical Mn3O4 microplate electrode exhibits remarkable cyclability up to 300 cycles at 500mAg(-1), accompanied with good rate capability (418mAhg(-1) at 2Ag(-1)).
Self-templated Hollow LiMn2O4 Nanofibers As Extremely Long Lifespan Lithium Ion Battery Cathode

Xu Jing,China University of Geosciences,Yu Zhihao,Le TrungHieu,Zhang Chuyan,Yang Ying

DOI: https://doi.org/10.1007/s10854-020-03770-4

2020-01-01

Journal of Materials Science Materials in Electronics

Abstract:The poor cyclability and inferior capacity retention caused by severe Jahn–Teller effect and dissolution of Mn ions into electrolyte during cycling hinder the commercial application of spinel LiMn2O4 with low cost and non-toxic. Herein, hollow LiMn2O4 nanofibers composed of LiMn2O4 nanograins are proposed, forming 3D network framework with uniform distribution. The slender and firm nanofibers can effectively buffer the irreversible phase transitions triggered by Mn3+ disproportionation and Jahn–Teller distortion and lead to the extremely long cycle life of LiMn2O4 cathode. Meanwhile, the huge specific surface area provided by hollow structure ensures the full contact between the materials and electrolyte, being beneficial to the diffusion of Li ions and transfer of electron to maintain its capacity. It can be observed that the capacity retention is 97.5% after 1000 cycles at 1C. The structure design of the hollow nanofibers modified the LiMn2O4 cathode material at the micro-level, which greatly improves the long-term cycling stability of the material and provides reference for the modification in lithium ion batteries.
Facile synthesis of porous hollow Co3O4 microfibers derived-from metal-organic frameworks as an advanced anode for lithium ion batteries

Yingying Chen,Yue Wang,Hongxun Yang,Hui Gan,Xingwei Cai,Xingmei Guo,Bo Xu,Minfeng Lü,Aihuai Yuan

DOI: https://doi.org/10.1016/j.ceramint.2017.05.004

IF: 5.532

2017-09-01

Ceramics International

Abstract:Co3O4, as a promising anode material for the next generation lithium ion batteries to replace graphite, displays high theoretical capacity (890mAhg−1) and excellent electrochemical properties. However, the drawbacks of its poor cycle performance caused by large volume changes during charge-discharge process and low initial coulombic efficiency due to large irreversible reaction impede its practical application. Herein, we have developed a porous hollow Co3O4 microfiber with 500nm diameter and 60nm wall thickness synthesized via a facile chemical precipitation method with subsequent thermal decomposition. As an advanced anode for lithium ion batteries, the porous hollow Co3O4 microfibers deliver an obviously enhanced electrochemical property in terms of lithium storage capacity (1177.4mAhg−1 at 100mAg−1), initial coulombic efficiency (82.9%) and cycle performance (76.6% capacity retention at 200th cycle). This enhancement could be attributed to the well-designed microstructure of porous hollow Co3O4 microfibers, which could increase the contact surface area between electrolyte and active materials and accommodate the volume variations via additional void space during cycling.

materials science, ceramics
Controllable Synthesis of Hollow MnFe2O4 by Self-Etching and Its Application in High-Performance Anode for Lithium-Ion Batteries

Chun Zhang,Chengzhao Jin,Guixiang Teng,Yinan Gu,Weigang Ma

DOI: https://doi.org/10.1016/j.cej.2019.02.004

IF: 15.1

2019-01-01

Chemical Engineering Journal

Abstract:The performance of anode materials is critical in further development of Li-ion batteries. However, the reversible capacity and cycling stability of anode materials are still far from satisfying. In this study, a new hollow MnFe2O4-carbon nanospheres (H-MnFe2O4-C) synthesized via an in-situ self-etching method was proposed. The MnFe2O4 served as the structural platform to embed the D-galactose coating layer followed by the in situ carbonization, the composite was then etched to form functional mesoporous H-MnFe2O4-C. The possible formation mechanism were discussed in detail. Based on the advantages of the hollow superstructure, close-packed configuration and uniform carbon coatings, which facilitate lithium-ion and electron transport while simultaneously alleviating the drastic volumetric change during cycling, the H-MnFe2O4-C exhibit high reversible capacity and outstanding cycling stability (with 973 mAh.g(-1) after 500 cycles at the current density of 0.2 A.g(-1), and 603 mAh.g(-1) at a high current density of 1 A.g(-1)), as well as high coulombic efficiency (> 98%). The findings in this study are useful for the engineering design of porous carbon-coated composite, which can be used for Li-ion batteries applications and other fields.

Porous MnFe2O4 Microrods As Advanced Anodes for Li-ion Batteries with Long Cycle Lifespan

A novel nanoporous Fe-doped lithium manganese phosphate material with superior long-term cycling stability for lithium-ion batteries

LiNi0.5Mn1.5O4 Microrod with Ultrahigh Mn3+ Content: A High Performance Cathode Material for Lithium Ion Battery

Porous ZnMn2O4 hollow microrods: Facile construction and excellent electrochemical performances for lithium ion batteries

Electrospun LiMn1.5Ni0.5O4 Hollow Nanofibers As Advanced Cathodes for High Rate and Long Cycle Life Li-ion Batteries

Superior lithium storage in Fe<sub>2</sub>O<sub>3</sub> nanoporous arrays endowed by surface phosphorylation and bulk phosphorous doping

Porous Α-Fe 2 O 3 Nanorods Supported on Carbon Nanotubes-Graphene Foam As Superior Anode for Lithium Ion Batteries

Intrinsic performance regulation in hierarchically porous Co3O4 microrods towards high-rate lithium ion battery anode

Improved Electrochemical Performance of Porous Fe3o4/Carbon Core/Shell Nanorods As an Anode for Lithium-Ion Batteries

Superior Capacity, Rate, Long Cycle Life and High Temperature Performance of Multilayered Porous Ultralong LiMn2O4 Nanorods for Lithium Ion Batteries

Three-dimensional cross-linked MnO/Sb hybrid nanowires co-embedded nitrogen-doped carbon tubes as high-performance anode materials for lithium-ion batteries

Carbon-coated MnFe2O4 nanoparticle hollow microspheres as high-performance anode for lithium-ion batteries

Porous Carbon Nanofibers Encapsulated with Peapod-Like Hematite Nanoparticles for High-Rate and Long-Life Battery Anodes.

Pedot-Pss Coated Zno/C Hierarchical Porous Nanorods As Ultralong-Life Anode Material for Lithium Ion Batteries

The use of silastic transhepatic stents in benign and malignant biliary strictures.

Porous CoO/Co3O4 nanoribbons as a superior performance anode material for lithium-ion batteries

Controlled synthesis of α-FeOOH nanorods and their transformation to mesoporous α-Fe2O3, Fe3O4@C nanorods as anodes for lithium ion batteries

Hierarchical Mn3O4 Microplates Composed of Stacking Porous Nanosheets for High-Performance Lithium Storage

Self-templated Hollow LiMn2O4 Nanofibers As Extremely Long Lifespan Lithium Ion Battery Cathode

Facile synthesis of porous hollow Co3O4 microfibers derived-from metal-organic frameworks as an advanced anode for lithium ion batteries

Controllable Synthesis of Hollow MnFe2O4 by Self-Etching and Its Application in High-Performance Anode for Lithium-Ion Batteries