Abstract:A n-butanol/diesel spray test system was constructed to conduct common rail bench test and constant volume bomb experiments in present work to investigate the impact of different n-butanol blending ratios on spray characteristics and the spray evolution process. To be specific, the research was carried out under the n-butanol blending ratios ofwith 0, 10%, 20%and 40% respectively to study various n-butanol blending ratio effects and to analyze the variation of the physical and chemical characteristics of the fuel. Then, the fuel spray patterns data at 0.4 ms was carefully collected and analyzed to compar the effect of different n-butanol blending ratios on spray penetration and spray angle. In addition, an-butanol/diesel spray model in engine cylinder was also established, to analyze how spray penetration and SMD of blended fuel varied during spray process, , as well as the impacts of n-butanol blending ratios on evaporation characteristics of blended fuel. Furthermore the various changes in velocity field and number density field in spray processes with different blending ratios have been taken into consideration and discussed for more detailed problems. It can be observed from the research data that: in normal temperature and pressure region,as the n-butanol blending ratio increased,the spray penetration decreased and there was a moderate rise in spray angle during spray process; as blending ratios of n-butanol increased by 40%, the spray penetration slightly reduced by 4.95%while reversely the spray angle climbed by 16.7%. Also when the injection pressure ascended, there was obvious rise both in the spray penetration and spray angle, particularly, if injection pressure rose by 40 MPa , the spray angle increased by 28.43°. During the spray evolution process, the n-butanol blending ratios influenced the spray penetration slightly, while in the very initial step of fuel blending process, the higher the n-butanol blending ratio was, the smaller SMD of blended fuel became. Along with the development of the spray process, however, the ultimate spray penetrations of different blended fuel were basically the same. In the injecting duration period, with the increasing of n-butanol blending ratio, there was a substantial drop in the mass of the fuel injected into the cylinder, and the peak velocity value of the jet dropped distinctly. Moreover, as a result of the fall in the viscosity and surface tension, the volatilization of blended fuel was apparently enhanced and subsequently fuel evaporation mass was increased slightly. The n-butanol blending ratios had quite limited impact on number density of drops but obviously facilitated the spray period, that is, the larger the blend ratio was, the better the spray characteristics would be. Besides this, in the central region of the downstream jet the figure of number density reached the highest.

(1-22) Characterization of Droplets and Vapor Concentration Distributions in Split-Injection Diesel Sprays by Processing UV and Visible Images((FS-2)Fuel Sprays 2-Diesel sprays)

Characterization of diesel spray with novel high-speed laser absorption scattering technique under diesel engine-like condition

Experimental Analysis in Dynamics Characteristics of Impinging Spray by a PFI Injector : from Spray Atomization to Fuel Adhesion Formation

Evaporation Characterization Of Fuel Spray Impinging On A Flat Wall By Laser-Based Measurement

Experimental Study on Microscopic and Macroscopic Characteristics of Diesel Spray with Split Injection

A Multi-Wavelength Extinction Imaging Diagnostic for Quantifying Diesel Spray Mixing at Engine-Relevant Conditions

Characterization of Direct-Injection Gasoline Sprays under Different Ambient and Fuel Injection Conditions

Microscopic Imaging on Diesel Spray and Atomization Process

Macroscopic and Microscopic Characterization of Diesel Spray under Room Temperature and Low Temperature with Split Injection

Near-nozzle Microscopic Characterization of Diesel Spray under Cold Start Conditions with Split Injection Strategy

Spray Dynamics of High Pressure Fuel Injectors for DI Gasoline Engines

Spray behavior of butanol-diesel and numerical simulation of mixture formation with engine

Schlieren and mie-scattering visualization of an evaporating spray under marine diesel engine conditions

Ultra-High Speed Imaging Study of the Diesel Spray Close to the Injector Tip at the Initial Opening Stage with Single Injection

Numerical Investigation of Diesel Spray Combustion Characteristics in the Ammonia/air Atmosphere

Initial Dynamic Development of Fuel Spray Analyzed by Ultra High Speed Imaging

Microscopic Study on the Mechanisms for Formation of the Initial Spray Morphology

Gasoline spray characteristics using a high pressure common rail diesel injection system by the method of laser induced exciplex fluorescence

Shape/penetration analysis and comparisons of isolated spray plumes in a multi-hole Diesel spray

Visualization on spray and flame characteristics of wall-impinging spray under marine diesel engine conditions

Evaluation of stabilizing and destabilizing effects on macroscopic and microscopic spray characteristics using dimensionless analysis