Abstract:As a newly emerged active flow control technique, micro blowing/suction has shown a great potential in reducing the skin friction of turbulent flows. Throughout comprehensive analyses of active flow control of micro blowing/suction devices for a NACA0015 airfoil by means of CFD technique, the effects on various characteristics such as lift and drag coefficients and separation areas are investigated in this study. The control devices were placed at 12%c, 30%c and 70%c from the leading edge (c is the chord length of the airfoil), respectively. The corresponding trends of flow separation control at these locations were analyzed with a varied range of angle of attacks (AOA). The two- and three-dimensional incompressible unsteady detached-eddy simulation (DES) was used, along with the k-e turbulence model, in solving the flow problem. The numerical computational results have demonstrated that: (1) Installing micro blowing/suction devices near the separation point is more efficient, as blowing can mix the jet flow and the incoming flow to energize the turbulent kinetic energy and suction can mitigate the flow of low turbulent kinetic energy, which leads to a result of reducing the separation. (2) Suction sometime has more effective influence than blowing, when the flow control devices are placed at 12%c and 30%c. When the control device is placed at 70%c, the effects of lift enhancement and drag reduction are almost the same regardless of blowing and/or suction method. When the AOA is less than 18°, both methods can achieve the goal of lift enhancement and drag reduction. When the AOA is larger than 18°, neither blowing nor suction is efficient. (3) The 3-D numerical simulation shows that the vortex structure evolves from a 2-D pattern near the separation point to a 3-D pattern in the downstream. However the characteristics of flow separation control over a 3-D airfoil simulation agrees well with 2-D numerical results. (4) Blowing at 30%c can move the separation point downstream from 70%c to 80%c at AOA=11°.

Numerical Simulation of Separated and Reattached Flows Around a Backward-Facing Step

Large Eddy Simulation of Separation Control over a Backward-Facing Step Flow by Suction

Les and Cdns Investigation of T106c Low Pressure Turbine

Large Eddy Simulation and CDNS Investigation of T106C Low-Pressure Turbine

Large Eddy Simulation Coupled with Immersed Boundary Method for Turbulent Flows over a Backward Facing Step

Numerical simulation of gas–particle dispersion in a backward-facing step flow with LES–FDF model

Effects of Micro Blowing/suction Flow Control Devices on a NACA0015 Airfoil

Lattice Boltzmann Modeling of Backward-Facing Step Flow Controlled by a Synthetic Jet

RETRACTED: Large Eddy Simulation of Turbulent Flow Downstream of a Backward-Facing Step

APPLICATION OF A TURBULENCE MODEL BASED ON VON KARMEN LENGTH SCALE IN STEADY AND UNSTEADY FLOW SIMULATION

High-fidelity Numerical Simulation of Unsteady Cavitating Flow Around a Hydrofoil

Turbulent Flows over a Backward Facing Step Simulated Using a Modified Partially Averaged Navier–Stokes Model

Large-Eddy and Detached-Eddy Simulations of the Separated Flow Around a Circular Cylinder

Numerical Study of Active Flow Control over a Hypersonic Backward-Facing Step Using Supersonic Jet in Near Space

Large Eddy Simulation of Flow Past a Square Cylinder Based on Dynamic Sub-Grid Scale Models

Two-fluid Large-Eddy Simulation of Backward-Facing Step Gas-Particle Flows and Validation of Second-Order-moment Two-Phase Turbulence Model

Numerical Simulation of Large Eddy Structures Evolution Behind Backward-Facing Step

Evaluation Of Particle Stochastic Separated Flow Models Via Large Eddy Simulation

Large-Eddy Simulation And Passive Control Of Flows For A Low Pressure Turbine Cascade

Unsteady Numerical Analysis of the Liquid-Solid Two-Phase Flow Around a Step Using Eulerian-Lagrangian and the Filter-Based RANS Method

Numerical Research of the Submerged High-Pressure Cavitation Water Jet Based on the RANS-LES Hybrid Model